Data List / Active Test

HINT:

Using the Techstream to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

1. Connect the Techstream to the DLC3.
2. Turn the engine switch on (IG).
3. Turn the Techstream on.
4. Enter the following menus: Body Electrical / Smart Key / Data List.
5. According to the display on the Techstream, read the Data List.

   Smart Key 

   DATA LIST
   
   

   Tester Display	Measurement Item/Range	Normal Condition	Diagnostic Note
   Ignition Switch	Engine switch on (IG) signal / ON or OFF	ON: Engine switch on (IG) OFF: Engine switch off or on (ACC)	-
   #Codes	Number of trouble codes	-	-
   Immobilizer	Engine immobilizer system status / Set or Unset	Set: Engine switch turned off Unset: Brake pedal depressed and key held close to engine switch	Before reading the Data List, remove the battery from the key.
   Master Key	Master key code signal / Match or No Match	Match: Master key code sent No Match: Unmatched master key code sent	-
   Different Encrypt Code	Transponder chip signal / OK or NG	OK: Correct data sent NG: Incorrect data sent	-
   Different Serial Number	Transponder chip signal / OK or NG	OK: Correct data sent NG: Incorrect data sent	-
   Frame Error	Transponder chip signal / OK or NG	OK: Correct data sent NG: Incorrect data sent	-
   Response	Transponder chip signal / OK or NG	OK: Correct data sent NG: Incorrect data sent	-
   BCC Malfunction	Transponder chip signal / OK or NG	OK: Correct data sent NG: Incorrect data sent	-
   Abnormal Status	Transponder chip data / OK or NG	OK: Data OK NG: Data error	-
   ID-BOX Sleep Condition	ID code box condition / Yes or No	Yes: ID code box in sleep condition No: ID code box not in sleep condition	-
   ID-BOX Start Condition	ID code box condition / Yes or No	Yes: ID code box sends wake up signal No: ID code box does not send wake up signal	-
   EFI Code Receive	EFI code receive (when DTC stored) / OK or NG	OK: EFI code received NG: EFI code not received	-
   S Code Check	S code verification result / OK or NG	OK: Verification confirmed NG: Verification not confirmed	-
   L Code Check	L code verification result / OK or NG	OK: Verification confirmed NG: Verification not confirmed	-
   Unlock Request Receive	Steering unlock command reception status / OK or NG	OK: Steering unlock request received NG: Steering unlock request not received	-
   Lock Request Receive	Steering lock command reception status / OK or NG	OK: Steering lock request received NG: Steering lock request is not received	-
   EFI communication	EFI communication / OK or NG	OK: EFI communication normal NG: EFI communication abnormal	-
   Engine Start Request	ID code box start request condition / OK or NG	OK: Start request condition signal received (past) NG: Start request condition signal not received (past)	-
   S Code Check (Past)	S code verification result (past) / OK or NG	OK: Verification confirmed (past) NG: Verification not confirmed (past)	-
   L Code Check (Past)	L code verification result (past) / OK or NG	OK: Verification confirmed (past) NG: Verification not confirmed (past)	-

HINT:

Using the Techstream to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.

1. Connect the Techstream to the DLC3.
2. Turn the engine switch on (IG).
3. Turn the Techstream on.
4. Enter the following menus: Body Electrical / Smart Key / Active Test.
5. According to the display on the Techstream, perform the Active Test.

   Smart Key 

   ACTIVE TEST CHART
   
   

   Tester Display	Test Part	Control Range	Diagnostic Note
   Security Indicator	Security indicator light	ON or OFF	-