Data List/Active Test

HINT:

Using Techstream to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

1. Connect Techstream to the DLC3.
2. Turn the ignition switch on (IG).
3. Turn the tester on.
4. Enter the following menus:

   Select: Body Electrical / Back Door or Main Body / Data List /

5. According to the display on the tester, read the "Data List".

   Back Door (Power back door ECU) 

   DIAGNOSTIC NOTE TABLE
   
   

   Tester Display	Measurement Item/Range	Normal Condition	Diagnostic Note
   PBD Close SW	Power back door closer switch signal / ON or OFF	ON Power back door closer switch is ON OFF Power back door closer switch is OFF	-
   PBD Main SW	Power back door main switch signal / ON or OFF	OK Power back door main switch is ON OFF Power back door main switch is OFF	-
   PBD Touch Sensor (Left)	Power back door touch sensor LH signal / ON or OFF	OK Power back door touch sensor LH pressed OFF Power back door touch sensor LH not pressed	-
   PBD Touch Sensor (Right)	Power back door touch sensor RH signal / ON or OFF	OK. Power back door touch sensor RH pressed OFF. Power back door touch sensor RH not pressed	-
   Door Lock Status	Back door lock condition signal / LOCK or UNLOCK	LOCK. Back door is locked UNLOCK Back door is unlocked	-
   Closer Position SW	Closer position switch signal / ON or OFF	ON Back door lock center gear is in center position OFF Back door lock center gear is out of center position	-
   Courtesy SW	Back door courtesy switch signal / ON or OFF	ON Back door is open OFF Back door is closed	-
   Half Latch SW	Half-latch switch signal / ON or OFF	ON Back door lock motor is open-latch or over-latch OFF Back door lock motor is full-latch or half-latch	-
   Door Position (close - 1/4) -1/4	Back door position (Full close -1/ 4 open) / CAUTION or OK	CAUTION: Back door position is not fully closed -1/4 opened OK Back door position is fully closed -1/4 opened	-
   Door Position (1/4 - 2/4) - 2/4	Back door position (1/4 open - 2/4 open) / CAUTION or OK	CAUTION: Back door position is not 1/4 opened - 2/4 opened OK. Back door position is 1/4 opened - 2/4 opened	-
   Door Position (2/4 - 3/4) - 3/4	Back door position (2/4 open - 3/4 open) / CAUTION or OK	CAUTION: Back door position is not 2/4 opened - 3/4 opened OK Back door position is 2/4 opened - 3/4 opened	-
   Door Position (3/4 - Open) - Open	Back door position (3/4 open - Full open) / CAUTION or OK	CAUTION: Back door position is not 3/4 opened - fully opened OK: Back door position is 3/4 opened - fully opened OK Back door position is 3/4 opened - fully opened	-

   Main Body (Main body ECU) 

   DIAGNOSTIC NOTE TABLE
   
   

   Tester Display	Measurement Item/Range	Normal Condition	Diagnostic Note
   B Dor Handle	Back door open switch signal / ON or OFF	ON Back door open switch is ON OFF Back door open switch is OFF	-
   Back Door Open SW	Back door opener / closer switch / ON or OFF	ON. Back door opener/closer switch is pushed OFF Back door opener/closer switch is not pushed	-

HINT:

Using Techstream to perform Active Test allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. The Data List can be displayed while performing Active Tests.

1. Connect Techstream to the DLC3.
2. Turn the ignition switch on (IG).
3. Turn the tester on.
4. Enter the following menus:

   Select: Body Electrical / Back Door / Active Test /

5. According to the display on the tester, perform the "Active Test".

   Back Door (Power back door ECU) 

   DIAGNOSTIC NOTE TABLE
   
   

   Tester Display	Test Part	Control Range	Diagnostic Note
   PBD Buzzer	Power back door buzzer sound	ON/OFF	-
   PBD Motor	Power back door motor	ON/OFF	-
   PBD Clutch	Power back door motor clutch	ON / OFF	-
   Latch Release	Latch release operation	ON / OFF	-