LEMON Manuals: Even more car manuals for everyone
Home >> Toyota >> 2008 >> FJ Cruiser RWD >> Repair and Diagnosis >> External Pages >> Different car >> Section 90 (Brakes - Abs) >> Vehicle Stability Control System >> Data List / Active Test

Data List / Active Test

WARNING: This page is about a different car, the 2007 Toyota RAV4. However, it is still accessible from the selected car via links, so may be relevant.
  1. READ DATA LIST 

    HINT:

    Using the intelligent tester's DATA LIST allows switch, sensor, actuator and other item values to be read without out removing any parts. Reading the DATA LIST early in troubleshooting is one way to save time.

    1. Connect the intelligent tester (with CAN VIM) to the DLC3.
    2. Turn the ignition switch ON.
    3. Turn the intelligent tester on.
    4. Read the DATA LIST according to the display on the tester.

      Skid control ECU 

      ITEM REFERENCE

      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      ABS WARN LAMP ABS warning light / ON or OFF ON: ABS warning light ON
      OFF: ABS warning light OFF      		 -
      VSC WARN LAMP VSC warning light / ON or OFF ON: VSC warning light ON
      OFF: VSC warning light OFF      		 -
      BRAKE WARN LAMP Brake warning light / ON or OFF ON: Brake warning light ON
      OFF: Brake warning light OFF      		 -
      SLIP INDI LAMP Slip indicator light / ON or OFF ON: Slip indicator light ON
      OFF: Slip indicator light OFF      		 -
      D-HILL LIGHT*9 Downhill assist control indicator light / ON or OFF ON: Downhill assist control switch ON
      OFF: Downhill assist control switch OFF      		 -
      AUTO LSD LAMP*10 AUTO LSD indicator light / ON or OFF ON: Traction control switch ON
      OFF: Traction control switch OFF      		 -
      BUZZER Skid control buzzer / ON or OFF ON: Buzzer ON
      OFF: Buzzer OFF      		 -
      STOP LAMP SW Stop light switch / ON or OFF ON: Brake pedal depressed
      OFF: Brake pedal released      		 -
      PARKING BRAKE SW Parking brake switch / ON or OFF ON: Parking brake applied
      OFF: Parking brake released      		 -
      BRK PEDAL SW Brake pedal load sensing switch / ON or OFF ON: Brake pedal depressed beyond the specified point
      OFF: Brake pedal not depressed beyond the specified point      		 -
      IDLE SW Main idle switch / ON or OFF ON: Accelerator pedal released
      OFF: Accelerator pedal depressed      		 -
      DAC SW*9 Downhill assist control switch / ON or OFF ON: Downhill assist control switch ON
      ON: Downhill assist control switch ON      		 -
      AUTO LSD SW*10 AUTO LSD switch / ON or OFF ON: AUTO LSD switch ON
      ON: AUTO LSD switch ON      		 -
      GEAR POSITION Gear position information / P/N, R, 1st-6th, FAIL, NOT R - -
      LEVER POSITION Shift lever position information / P/N, R, D/M, 1st-6th/B, FAIL - -
      SHIFT INFO Shift information / ON or OFF ON: During gear change -
      MAS CYL PRESS 1 Master cylinder pressure sensor 1 reading / min.: 0 V, max.: 5 V When brake pedal released: 0.3 to 0.9 V Reading increases when brake pedal depressed
      ZERO M/C SEN Memorized zero point value of master cylinder pressure sensor / min.: -12.5 MPa, max.: 12.4 MPa Min.: -12.5 MPa
      Max.: 12.4 MPa      		 -
      DECELERAT SEN Deceleration sensor 1 reading / min.: -18.52 m/s2 , max.: 18.39 m/s2 Min.: -18.52 m/s2
      Max.: 18.39 m/s2      		 -
      ZERO DECELERAT Memorized zero point value of deceleration sensor 1 / min.: - 25.11 m/s2 , max.: 24.91 m/s2 Min.: -25.11 m/s2
      Max.: 24.91 m/s2      		 -
      DECELERAT SEN 2 Deceleration sensor 2 reading / min.: -18.52 m/s2 , max.: 18.39 m/s2 Min.: -18.52 m/s2
      Max.: 18.39 m/s2      		 -
      ZERO DECELERAT 2 Memorized zero point value of deceleration sensor 2 / min.: - 25.11 m/s2 , max.: 24.91 m/s2 Min.: -25.11 m/s2
      Max.: 24.91 m/s2      		 -
      YAW RATE SENS 1 Yaw rate sensor 1 reading / min.: - 128 deg/s, max.: 127 deg/s Min.: -128 deg/s
      Max.: 127 deg/s      		 -
      YAW RATE SENS 2 Yaw rate sensor 2 reading / min.: - 128 deg/s, max.: 127 deg/s Min.: -128 deg/s
      Max.: 127 deg/s      		 -
      ZERO YAW RATE Memorized zero point value of yaw rate sensor 1 / min.: -128 deg/s, max.: 127 deg/s Min.: -128 deg/s
      Max.: 127 deg/s      		 -
      STEERING SEN Steering sensor reading / min.: - 3276.8 deg, max.: 3276.7 deg Left turn: Increase
      Right turn: Decrease      		 -
      ZERO STEERING Memorized zero point value of steering sensor / min.: -3276.8 deg, max.: 3276.7 deg Min.: -3276.8 deg
      Max.: 3276.7 deg      		 -
      LATERAL G Lateral G / min.: -25.11 m/s2 , max.: 24.91 m/s2 Min.: -25.11 m/s2
      Max.: 24.91 m/s2      		 -
      FORWARD&REA G Forward and rearward G / min.: - 25.11 m/s2 , max.: 24.91 m/s2 Min.: -25.11 m/s2
      Max.: 24.91 m/s2      		 -
      YAW RATE VALUE Yaw rate value / min.: -128 deg/s, max.: 127 deg/s Min.: -128 deg/s
      Max.: 127 deg/s      		 -
      STEERING ANGLE Steering angle value / min.: - 3276.8 deg, max.: 3276.7 deg Min.: -3276.8 deg
      Max.: 3276.7 deg      		 -
      FR WHEEL SPD Wheel speed sensor (FR) reading / min.: 0 km/h (0 mph), max.: 326.4 km/h (202.8 mph) Actual wheel speed Similar to speed indicated on speedometer
      FL WHEEL SPD Wheel speed sensor (FL) reading / min.: 0 km/h (0 mph), max.: 326.4 km/h (202.8 mph) Actual wheel speed Similar to speed indicated on speedometer
      RR WHEEL SPD Wheel speed sensor (RR) reading / min.: 0 km/h (0 mph), max.: 326.4 km/h (202.8 mph) Actual wheel speed Similar to speed indicated on speedometer
      RL WHEEL SPD Wheel speed sensor (RL) reading / min.: 0 km/h (0 mph), max.: 326.4 km/h (202.8 mph) Actual wheel speed Similar to speed indicated on speedometer
      VEHICLE SPD Maximum speed sensor reading / min.: 0 km/h (0 mph), max.: 326.4 km/h (202.8 mph) Actual wheel speed Similar to speed indicated on speedometer
      FR WHEEL ACCEL FR wheel acceleration / min.: - 200.84 m/s2 , max.: 199.27 m/s2 Min.: -200.84 m/s2
      Max.: 199.27 m/s2      		 -
      FL WHEEL ACCEL FL wheel acceleration / min.: - 200.84 m/s2 , max.: 199.271 m/s2 Min.: -200.84 m/s2
      Max.: 199.27 m/s2      		 -
      RR WHEEL ACCEL RR wheel acceleration / min.: - 200.84 m/s2 , max.: 199.27 m/s2 Min.: -200.84 m/s2
      Max.: 199.27 m/s2      		 -
      RL WHEEL ACCEL RL wheel acceleration / min.: - 200.84 m/s2 , max.: 199.27 m/s2 Min.: -200.84 m/s2
      Max.: 199.27 m/s2      		 -
      FR ABS STATUS FR wheel ABS control status / ON or OFF ON: During control -
      FL ABS STATUS FL wheel ABS control status / ON or OFF ON: During control -
      RR ABS STATUS RR wheel ABS control status / ON or OFF ON: During control -
      RL ABS STATUS RL wheel ABS control status / ON or OFF ON: During control -
      RR EBD STATUS RR wheel EBD control status / ON or OFF ON: During control -
      RL EBD STATUS RL wheel EBD control status / ON or OFF ON: During control -
      BA STATUS BA control status / ON or OFF ON: During control -
      TRAC STATUS TRC control status / ON or OFF ON: During control -
      TRAC ENG STATUS TRC engine control status / ON or OFF ON: During control -
      TRAC BRK STATUS TRC brake control status / ON or OFF ON: During control -
      FR VSC STATUS FR wheel VSC control status / ON or OFF ON: During control -
      FL VSC STATUS FL wheel VSC control status / ON or OFF ON: During control -
      RR VSC STATUS RR wheel VSC control status / ON or OFF ON: During control -
      RL VSC STATUS RL wheel VSC control status / ON or OFF ON: During control -
      ENG REVOLUTIONS Engine revolutions / min.: 0 r/min, max.: 65535 r/min - -
      ENGINE TORQUE Real engine torque / min.: -1024 Nm, max.: 1023 Nm - -
      ACCELERATOR % Percentage of accelerator pedal opening angle / min.: 0%, max.: 128% - -
      SOL RELAY Solenoid relay / ON or OFF ON: Solenoid relay ON
      OFF: Solenoid relay OFF      		 -
      ELECTRONICALLY CONTROLLED BRAKE SYSTEM MTR RELAY Electronically Controlled Brake System Motor relay (VSC1 relay) / ON or OFF ON: Motor relay ON
      OFF: Motor relay OFF      		 -
      FAIL MTR RELAY Fail-safe motor relay / ON or OFF ON: Motor relay ON
      OFF: Motor relay OFF      		 -
      SM2 TRC / VSC solenoid (SM2) / ON or OFF ON: Operates -
      SM1 TRC / VSC solenoid (SM1) / ON or OFF ON: Operates -
      SFRH*1 ABS solenoid (SFRH) / ON or OFF ON: Operates
      OFF: Does not operate      		 -
      SFRR*2 ABS solenoid (SFRR) / ON or OFF ON: Operates
      OFF: Does not operate      		 -
      SFLH*3 ABS solenoid (SFLH) / ON or OFF ON: Operates
      OFF: Does not operate      		 -
      SFLR*4 ABS solenoid (SFLR) / ON or OFF ON: Operates
      OFF: Does not operate      		 -
      SRRH*5 ABS solenoid (SRRH) / ON or OFF ON: Operates
      OFF: Does not operate      		 -
      SRRR*6 ABS solenoid (SRRR) / ON or OFF ON: Operates
      OFF: Does not operate      		 -
      SRLH*7 ABS solenoid (SRLH) / ON or OFF ON: Operates
      OFF: Does not operate      		 -
      SRLR*8 ABS solenoid (SRLR) / ON or OFF ON: Operates
      OFF: Does not operate      		 -
      FR SPD OPN FR speed sensor open detection / ERROR or NORMAL ERROR: Momentary interruption
      NORMAL: Normal      		 -
      FL SPD OPN FL speed sensor open detection / ERROR or NORMAL ERROR: Momentary interruption
      NORMAL: Normal      		 -
      RR SPD OPN RR speed sensor open detection / ERROR or NORMAL ERROR: Momentary interruption
      NORMAL: Normal      		 -
      RL SPD OPN RL speed sensor open detection / ERROR or NORMAL ERROR: Momentary interruption
      NORMAL: Normal      		 -
      EFI COM OPN EFI communication open detection / ERROR or NORMAL ERROR: Momentary interruption
      NORMAL: Normal      		 -
      YAW RATE OPN Yaw rate sensor open detection / ERROR or NORMAL ERROR: Momentary interruption
      NORMAL: Normal      		 -
      DECELERAT OPN Deceleration sensor open detection / ERROR or NORMAL ERROR: Momentary interruption
      NORMAL: Normal      		 -
      STEERING OPN Steering angle sensor open detection / ERROR or NORMAL ERROR: Momentary interruption
      NORMAL: Normal      		 -
      M/C OPN Master cylinder pressure sensor open detection / ERROR or NORMAL ERROR: Momentary interruption
      NORMAL: Normal      		 -
      #DTC Number of recorded DTCs/min.: 0, max.: 25 Min.: 0
      Max.: 255      		 -
      INSPECTION MODE Inspection mode / OTHER or INSPECT - -
      #IG ON2 Number of ignition switch ON operations after entering the inspection mode / min.: 0, max.: 255 - -

      HINT:

      • *1: SFRH (S: Solenoid, F: Front, R: Right, H: Holding)
      • *2: SFRR (S: Solenoid, F: Front, R: Right, R: Reduction)
      • *3: SFLH (S: Solenoid, F: Front, L: Left, H: Holding)
      • *4: SFLR (S: Solenoid, F: Front, L: Left, R: Reduction)
      • *5: SRRH (S: Solenoid, R: Rear, R: Right, H: Holding)
      • *6: SRRR (S: Solenoid, R: Rear, R: Right, R: Reduction)
      • *7: SRLH (S: Solenoid, R: Rear, L: Left, H: Holding)
      • *8: SRLR (S: Solenoid, R: Rear, L: Left, R: Reduction)
      • *9: w/Downhill assist control
      • *10: for 2WD (w/AUTO LSD)
  2. PERFORM ACTIVE TEST 

    HINT:

    Performing the intelligent tester's ACTIVE TEST allows relay, VSV, actuator and other items to be operated without removing any parts. Performing the ACTIVE TEST early in troubleshooting is one way to save time. The DATA LIST can be displayed during the ACTIVE TEST.

    1. Connect the intelligent tester (with CAN VIM) to the DLC3.
    2. Turn the ignition switch ON.
    3. Turn the intelligent tester on.
    4. Perform the ACTIVE TEST according to the display on the tester.

      HINT:

      • The ignition switch must be turned ON to proceed to the ACTIVE TEST using the intelligent tester.
      • The ACTIVE TESTs of the ABS solenoid, ABS motor relay, ABS warning light and BRAKE warning light are available when the vehicle is stopped.
      • The motors stop automatically after 5 seconds of activation to prevent them from being damaged. When the motors are driven repeatedly, certain intervals are required.
      • Each solenoid stops automatically after 2 seconds of activation to prevent them from being damaged, and can be operated again after a certain interval.
      • Do not depress the brake pedal while only the pressure reduction solenoid valves are on.
      • Do not drive 2 or more solenoids simultaneously except to operate the pressure holding solenoid valves and pressure reduction solenoid valves of each wheel.

        Skid control ECU 

        TESTER DISPLAY

        Tester Display Test Part Control Range
        ABS WARN LAMP Turns ABS warning light ON / OFF Observe combination meter
        VSC WARN LAMP Turns VSC warning light ON / OFF Observe combination meter
        BRAKE WARN LAMP Turns Brake warning light ON / OFF Observe combination meter
        SLIP INDI LAMP Turns Slip indicator light ON / OFF Observe combination meter
        D-HILL LIGHT*1 Turns downhill assist control indicator light ON / OFF Observe combination meter
        AUTO LSD LAMP*2 Turns AUTO LSD indicator light ON / OFF Observe combination meter
        BUZZER Turns skid control buzzer ON / OFF Buzzer can be heard
        STP LAMP RELAY Turns stop light relay (BRK relay) ON / OFF Operation sound of motor can be heard
        SOL RELAY Turns ABS solenoid relay ON / OFF -
        MOTOR RELAY Turns ABS motor relay ON / OFF Operation sound of motor can be heard
        SRLR Turns ABS solenoid (SRLR) ON / OFF Operation sound of solenoid (clicking sound) can be heard
        SRLH Turns ABS solenoid (SRLH) ON / OFF Operation sound of solenoid (clicking sound) can be heard
        SRRR Turns ABS solenoid (SRRR) ON / OFF Operation sound of solenoid (clicking sound) can be heard
        SRRH Turns ABS solenoid (SRRH) ON / OFF Operation sound of solenoid (clicking sound) can be heard
        SFLR Turns ABS solenoid (SFLR) ON / OFF Operation sound of solenoid (clicking sound) can be heard
        SFLH Turns ABS solenoid (SFLH) ON / OFF Operation sound of solenoid (clicking sound) can be heard
        SFRR Turns ABS solenoid (SFRR) ON / OFF Operation sound of solenoid (clicking sound) can be heard
        SFRH Turns ABS solenoid (SFRH) ON / OFF Operation sound of solenoid (clicking sound) can be heard
        SMR Turns VSC / TRC solenoid (SMR) ON / OFF Operation sound of solenoid (clicking sound) can be heard
        SMF Turns VSC / TRC solenoid (SMF (BA-SOL)) ON / OFF Operation sound of solenoid (clicking sound) can be heard

        HINT:

        *1: w/Downhill assist control

        *2: for 2WD (w/AUTO LSD)

scientia non olet · About LEMON Manuals