Inspection Procedure

HINT:

• When U0073/94, U0123/62, U0124/95 or U0126/63 is output together with C1231/31, inspect and repair the trouble areas indicated by U0073/94, U0123/62, U0124/95 or U0126/63 first.
• When there are problems with the speed sensor or the yaw rate sensor, DTCs for the steering sensor may be output even when the steering sensor is normal. When DTCs for the speed sensor or yaw rate sensor are output together with other DTCs for the steering sensor, inspect and repair the speed sensor and yaw rate sensor first, and then inspect and repair the steering sensor.

1. CHECK HARNESS AND CONNECTOR (MOMENTARY INTERRUPTION) 
   1. Using the DATA LIST of the intelligent tester, check for any momentary interruptions in the wire harness and connectors between the skid control ECU and the steering sensor (see CHECK FOR INTERMITTENT PROBLEMS ).

      Skid control ECU 

      ITEM REFERENCE
      
      

      Item (Display)	Measurement Item / Range (Display)	Normal Condition	Diagnostic Note
      STEERING OPN	Steering angle sensor open detection / ERROR or NORMAL	ERROR: Momentary interruption NORMAL: Normal	-

      OK: There are no momentary interruptions. 

      HINT:

      Perform the above inspection before removing the sensor and connector.

   NG: Go to step   4 

   OK: GO TO NEXT STEP. 

2. CHECK DTC 
   1. Clear the DTC (see DTC CHECK / CLEAR ).
   2. Turn the ignition switch OFF.
   3. Turn the ignition switch ON again and check that no CAN communication system DTC is output.
   4. Drive the vehicle and turn the steering wheel to the right and left at a speed of 35 km/h (24 mph) and check that no speed and yaw rate sensor DTCs are output.

      Result 

      RESULT PROCEED
      
      

      Result	Proceed to
      DTC is not output	A
      CAN communication system DTC is output	B
      Speed sensor or yaw rate sensor DTC is output	C

   B: CHECK CAN COMMUNICATION SYSTEM 

   C: REPAIR CIRCUIT INDICATED BY OUTPUT DTC 

   A: GO TO NEXT STEP. 

3. CHECK WIRE HARNESS (STEERING SENSOR - BATTERY AND BODY GROUND) 
   1. Remove the steering wheel assembly and the column cover.
   2. Disconnect the E11 sensor connector. (See Fig 1).
   3. Measure the voltage of the wire harness side connector.

      Standard voltage 

      TESTER CONNECTION SPECIFIED CONDITION
      
      

      Tester Connection	Condition	Specified Condition
      E11-1(IG) - Body ground	Ignition switch ON	10 to 14 V
      E11-3 (BAT) - Body ground	Always	10 to 14 V

   4. Measure the resistance of the wire harness side connector.

      Standard resistance 

      TESTER CONNECTION SPECIFIED CONDITION
      
      

      Tester Connection	Specified Condition
      E11-2 (ESS) - Body ground	Below 1Ω

      Fig 1: Identifying Steering Sensor Harness Connector Terminals

      Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

   NG: REPAIR OR REPLACE HARNESS AND CONNECTOR 

   OK: REPLACE STEERING SENSOR 

4. REPAIR OR REPLACE HARNESS AND CONNECTOR (STEERING SENSOR TO SKID CONTROL ECU) 
5. RECONFIRM DTC 
   1. Clear the DTC (see DTC CHECK / CLEAR ).
   2. Start the engine.
   3. Drive the vehicle and turn the steering wheel to the right and left at a speed of 45 km/h (28 mph) or more for several seconds.
   4. Check if the same DTC is recorded (see DTC CHECK / CLEAR ).

      Result 

      RESULT PROCEED
      
      

      Result	Proceed to
      DTC is not output	A
      DTC is output	B

   B: Go to step   2 

   A: END