LEMON Manuals: Even more car manuals for everyone
Home >> Toyota >> 2008 >> FJ Cruiser RWD >> Repair and Diagnosis >> External Pages >> Different car >> Section 230 (Automatic Transmission - U241E) >> Automatic Transaxle System >> DTC P0705 Transmission Range Sensor Circuit Malfunction (PRNDL Input) >> Inspection Procedure

Inspection Procedure

WARNING: This page is about a different car, the 2008 Toyota RAV4. However, it is still accessible from the selected car via links, so may be relevant.

HINT:

Using Techstream's Data List allows switch, sensor, actuator and other item values to be read without removing any parts. Reading the Data List early in troubleshooting is one way to save time.

NOTE: In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
  1. Warm up the engine.
  2. Turn the ignition switch OFF.
  3. Connect Techstream to the DLC3.
  4. Turn the ignition switch ON and turn the tester ON.
  5. Enter the following menus: Powertrain / Engine and ECT / Data List.
  6. Follow the instructions on the tester and read the Data List.
    DATA LIST

    Tester Display Measurement Item/Range Normal Condition Diagnostic Note
    Neutral Position SW Signal PNP switch status/ ON or OFF Shift lever is:
    On P or N: ON
    Not on P or N: OFF    		 When shift lever position displayed on Techstream differs from actual position, adjustment of PNP switch or shift cable may be incorrect
    Shift SW Status (R Range) PNP switch status/ ON or OFF Shift lever is:
    On R: ON
    Not on R: OFF    		 When shift lever position displayed on Techstream differs from actual position, adjustment of PNP switch or shift cable may be incorrect
    Shift SW Status (P Range) PNP switch status/ ON or OFF Shift lever is:
    On P: ON
    Not on P: OFF    		 When shift lever position displayed on Techstream differs from actual position, adjustment of PNP switch or shift cable may be incorrect
    Shift SW Status (N Range) PNP switch status/ ON or OFF Shift lever is:
    On N: ON
    Not on N: OFF    		 When shift lever position displayed on Techstream differs from actual position, adjustment of PNP switch or shift cable may be incorrect
    Shift SW Status (D Range) PNP switch status/ ON or OFF Shift lever is:
    On D: ON
    Not on D: OFF    		 When shift lever position displayed on Techstream differs from actual position, adjustment of PNP switch or shift cable may be incorrect
    Shift SW Status (3 Range) PNP switch status/ ON or OFF Shift lever is:
    On 3: ON
    Not on 3: OFF    		 When shift lever position displayed on Techstream differs from actual position, adjustment of PNP switch or shift cable may be incorrect
    Shift SW Status (2 Range) PNP switch status/ ON or OFF Shift lever is:
    On 2: ON
    Not on 2: OFF    		 When shift lever position displayed on Techstream differs from actual position, adjustment of PNP switch or shift cable may be incorrect
    Shift SW Status (L Range) PNP switch status/ ON or OFF Shift lever is:
    On L: ON
    Not on L: OFF    		 When shift lever position displayed on Techstream differs from actual position, adjustment of PNP switch or shift cable may be incorrect
  1. CHECK WIRE HARNESS (PARK/NEUTRAL POSITION SWITCH - BATTERY) 
    1. Disconnect the B26 park/neutral position switch connector.
      2. Fig 1: Identifying Terminals Of B26 Park/Neutral Position Switch Connector
      G05584090Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Turn the ignition switch ON.
    3. Measure the voltage.

      Standard voltage 

      TERMINALS VOLTAGE REFERENCE

      Tester Connection Specified Condition
      2 (RB) - Body ground 10 to 14 V

    NG: CHECK POWER SOURCE OF ECM 

    OK: go to next step 

  2. INSPECT PARK/NEUTRAL POSITION SWITCH 
    1. Disconnect the B26 park/neutral position switch connector.
      2. Fig 2: Identifying Terminals Of Park/Neutral Position Switch Connector
      G05584091Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Measure the resistance of the park/neutral position switch when the shift lever is moved to each position.

      Standard resistance 

      TERMINALS RESISTANCE REFERENCE

      Tester Connection Shift Lever Position Specified Condition
      6 (PL) - 2 (RB) P Below 1 Ω
      6 (PL) - 2 (RB) Not on P 10 kΩ or higher
      1 (RL) - 2 (RB) R Below 1 Ω
      1 (RL) - 2 (RB) Not on R 10 kΩ or higher
      9 (NL) - 2 (RB) N Below 1 Ω
      9 (NL) - 2 (RB) Not on N 10 kΩ or higher
      7 (DL) - 2 (RB) D Below 1 Ω
      7 (DL) - 2 (RB) Not on D 10 kΩ or higher
      3 (2L) - 2 (RB) 2 Below 1 Ω
      3 (2L) - 2 (RB) Not on 2 10 kΩ or higher
      8 (LL) - 2 (RB) L Below 1 Ω
      8 (LL) - 2 (RB) Not on L 10 kΩ or higher

    NG: REPLACE PARK/NEUTRAL POSITION SWITCH 

    OK: go to next step 

  3. CHECK WIRE HARNESS (ECM - BATTERY AND BODY GROUND) 
    1. Disconnect the B30 ECM connector.
      2. Fig 3: Identifying Terminals Of B30 ECM Connector
      G05584092Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Turn the ignition switch ON.
    3. Measure the voltage of the wire harness side connector.

      Standard voltage 

      TERMINALS VOLTAGE REFERENCE

      Tester Connection Shift Lever Position Specified Condition
      B30-73 (P) - Body ground P 10 to 14 V
      B30-73 (P) - Body ground Not on P Below 1 V
      B30-53 (R) - Body ground R 10 to 14 V*
      B30-53 (R) - Body ground Not on R Below 1 V
      B30-54 (N) - Body ground N 10 to 14 V
      B30-54 (N) - Body ground Not on N Below 1 V
      B30-56 (D) - Body ground D or 3 10 to 14 V
      B30-56 (D) - Body ground Not on D or 3 Below 1 V
      B30-55 (2) - Body ground 2 10 to 14 V
      B30-55 (2) - Body ground Not on 2 Below 1 V
      B30-74 (L) - Body ground L 10 to 14 V
      B30-74 (L) - Body ground Not on L Below 1 V
      HINT:
      *: The voltage will drop slightly due to the illumination of the back-up light.

    NG: REPAIR OR REPLACE HARNESS AND CONNECTOR 

    OK: go to next step 

  4. CHECK WIRE HARNESS (PARK/NEUTRAL POSITION SWITCH - SHIFT LOCK CONTROL UNIT ASSEMBLY) 
    1. Disconnect the E40 switch connector.
      2. Fig 4: Identifying Terminals Of E40 Switch Connector
      G05584093Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Turn the ignition switch ON.
    3. Measure the voltage when the shift lever is moved to each position.

      Standard voltage 

      TERMINALS VOLTAGE REFERENCE

      Tester Connection Shift Lever Position Specified Condition
      1 (NSSD) - Body ground D and 3 10 to 14 V
      1 (NSSD) - Body ground Not on D and 3 Below 1 V

    NG: REPAIR OR REPLACE HARNESS AND CONNECTOR 

    OK: go to next step 

  5. INSPECT SHIFT LOCK CONTROL UNIT ASSEMBLY 
    1. Disconnect the E40 switch connector.
      2. Fig 5: Identifying Terminals Of E40 Switch Connector
      G05584094Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Measure the resistance of the switch when the shift lever is moved to each position.

      Standard resistance 

      TERMINALS RESISTANCE REFERENCE

      Tester Connection Shift Lever Position Specified Condition
      1 (NSSD) - 2 (AT3) D 10 kΩ or higher
      1 (NSSD) - 2 (AT3) 3 Below 1 Ω

    NG: REPLACE SHIFT LOCK CONTROL UNIT ASSEMBLY 

    OK: go to next step 

  6. CHECK WIRE HARNESS (SHIFT LOCK CONTROL UNIT ASSEMBLY - BATTERY AND BODY GROUND) 
    1. Disconnect the A9 ECM connector.
      2. Fig 6: Identifying Terminals Of A9 ECM Connector
      G05584095Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Turn the ignition switch ON.
    3. Measure the voltage of the wire harness side connector.

      Standard voltage 

      TERMINALS VOLTAGE REFERENCE

      Tester Connection Shift Lever Position Specified Condition
      A9-26 (3) - Body ground 3 10 to 14 V
      A9-26 (3) - Body ground Not on 3 Below 1 V

      HINT:

      *: The voltage will drop slightly due to the illumination of the back-up light.

    NG: REPAIR OR REPLACE HARNESS AND CONNECTOR 

    OK: REPLACE ECM 

scientia non olet · About LEMON Manuals