Inspection Procedure

WARNING: This page is about a different car, the 2008 Toyota RAV4. However, it is still accessible from the selected car via links, so may be relevant.

CHECK CONNECTION OF CONNECTOR
1. Turn the ignition switch OFF.
2. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
3. Check that the connectors are properly connected to the center airbag sensor, rear airbag sensor RH and the side airbag sensor RH.
  OK:
  
  The connectors are properly connected.
NG: CONNECT CONNECTOR

OK: Go to next step

CHECK FLOOR WIRE NO. 2 (OPEN)

Disconnect the connectors from the center airbag sensor and the side airbag sensor RH.
Using a service wire, connect L10-4 (BBR+) and L10-3 (BBR-) of connector C.
NOTE: Do not forcibly insert the service wire into the terminals of the connector when connecting.

Measure the resistance of the wire harness side connectors.

Standard resistance

TESTER CONNECTION SPECIFIED CONDITION

Tester Connection	Specified Condition
L7-17 (BBP+) - L7-18 (BBP-)	Below 1 Ω

Fig 1: Identifying Floor Wire No. 2 (Open)

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

NG: REPAIR OR REPLACE FLOOR WIRE NO. 2

OK: Go to next step

CHECK FLOOR WIRE NO. 2 (SHORT)

Disconnect the service wire from connector C.

Measure the resistance of the wire harness side connector.

Standard resistance

TESTER CONNECTION SPECIFIED CONDITION

Tester Connection	Specified Condition
L7-17 (BBP+) - L7-18(BBP-)	1 MΩ or higher

Fig 2: Identifying Floor Wire No. 2 (Short)

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

NG: REPAIR OR REPLACE FLOOR WIRE NO. 2

OK: Go to next step

CHECK FLOOR WIRE NO. 2 (TO B+)

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch ON.

Measure the voltage of the wire harness side connector.

Standard voltage

TESTER CONNECTION SPECIFIED CONDITION

Tester Connection	Specified Condition
L7-17 (BBP+) - Body ground	Below 1 V
L7-18 (BBP-) - Body ground	Below 1 V

Fig 3: Identifying Floor Wire No. 2 (To B+)

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

NG: REPAIR OR REPLACE FLOOR WIRE NO. 2

OK: Go to next step

CHECK FLOOR WIRE NO. 2 (TO GROUND)

Turn the ignition switch OFF.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

Measure the resistance of the wire harness side connector.

Standard resistance

TESTER CONNECTION SPECIFIED CONDITION

Tester Connection	Specified Condition
L7-17 (BBP+) - Body ground	1 MΩ or higher
L7-18 (BBP-) - Body ground	1 MΩ or higher

Fig 4: Identifying Floor Wire No. 2 (To Ground)

NG: REPAIR OR REPLACE FLOOR WIRE NO. 2

OK: Go to next step

CHECK SIDE AIRBAG SENSOR RH

Connect the connectors to the center airbag sensor.
Interchange the side airbag sensor RH with the side airbag sensor LH and connect the connectors to them.

Fig 5: Identifying Side Airbag Sensor RH
Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch ON, and wait for at least 60 seconds.
Clear the DTCs (see DTC CHECK / CLEAR ).
Turn the ignition switch OFF.
Turn the ignition switch ON, and wait for at least 60 seconds.

Check for DTCs (see DTC CHECK / CLEAR ).

Result

RESULT

Result	Proceed to
DTC B1622/81 and B1627/82 are not output	A
DTC B1622/81 is output	B
DTC B1627/82 is output	C

HINT:

DTCs other than DTC B1622/81 and B1627/82 may be output at this time, but they are not related to this check.

B: REPLACE SIDE AIRBAG SENSOR RH

C: REPLACE CENTER AIRBAG SENSOR ASSEMBLY

A: USE SIMULATION METHOD TO CHECK