NAME PLATE (for Hatchback): Installation

WARNING: This page is about a different car, the 2008 Toyota Yaris. However, it is still accessible from the selected car via links, so may be relevant.

INSTALL NO. 2 LUGGAGE COMPARTMENT DOOR NAME PLATE

Clean the attachment surface.
1. Using an infrared light, heat the double-sided adhesive tape remaining on the back door panel.
  HINT:
  
  Heat at 40 to 60°C (104 to 140°F) for 1 to 2 minutes.
2. Using a shop rag or piece of cloth, rub the double-sided adhesive tape off the back door panel while it is hot from the infrared light.
  NOTE: Installing the No. 2 luggage compartment door name plate while any double-sided tape remains on the back door panel may cause adhesion failure. Therefore, completely remove the double-sided tape.
3. Using a non-residue solvent, clean the attachment surface.

Install a new No. 2 luggage compartment door name plate as shown in the illustration.

Fig 1: Identifying Peeling Paper

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

Installation position

MARK MEASUREMENT CHART

Mark	Measurement (along surface)
a	158.8 mm (6.252 In.)
b	40.3 mm (1.587 In.)
c	255.9 mm (10.075 In.)
d	157.6 mm (6.205 In.)

NOTE: Install the No. 2 luggage compartment door name plate in an environment where the ambient temperature is over 20°C (68°F). If it is below 20°C (68°F), using an infrared light, heat the back door panel and the No. 2 luggage compartment door name plate up to 20 to 30°C (68 to 86°F) and install the No. 2 luggage compartment door name plate.

INSTALL NO. 1 LUGGAGE COMPARTMENT DOOR NAME PLATE

Clean the attachment surface.
1. Using an infrared light, heat the double-sided adhesive tape remaining on the back door panel.
  HINT:
  
  Heat at 40 to 60°C (104 to 140°F) for 1 to 2 minutes.
2. Using a shop rag or piece of cloth, rub the double-sided adhesive tape off the back door panel while it is hot from the infrared light.
  NOTE: Installing the No. 1 luggage compartment door name plate while any double-sided tape remains on the back door panel may cause adhesion failure. Therefore, completely remove the double-sided tape.
3. Using a non-residue solvent, clean the attachment surface.

Install a new No. 1 luggage compartment door name plate as shown in the illustration.

Fig 2: Identifying Peeling Paper

Installation position

MARK MEASUREMENT CHART

Mark	Measurement (along surface)
a	158.5 mm (6.24 In.)
b	41.7 mm (1.642 In.)
c	266.1 mm (10.476 In.)
d	156.4 mm (6.157 In.)

NOTE: Install the No. 1 luggage compartment door name plate in an environment where the ambient temperature is over 20°C (68°F). If it is below 20°C (68°F), using an infrared light, heat the back door panel and the No. 1 luggage compartment door name plate up to 20 to 30°C (68 to 86°F) and install the No. 1 luggage compartment door name plate.

INSTALL SYMBOL EMBLEM
1. Clean the attachment surface.
  1. Using an infrared light, heat the double-sided adhesive tape remaining on the back door panel.
    HINT:
    
    Heat at 40 to 60°C (104 to 140°F) for 1 to 2 minutes.
  2. Using a shop rag or piece of cloth, rub the remaining double-sided adhesive tape off the back door panel while it is hot from the infrared light.
    NOTE: Installing the symbol emblem with any double-sided tape remaining on the back door panel may cause adhesion failure. Therefore, completely remove the double-sided tape.
  3. Using a non-residue solvent, clean the attachment surface.
2. Insert the 2 bosses into the back door panel and install the symbol emblem.
  NOTE: Install the symbol emblem in an environment where the ambient temperature is over 20 °C (68 F). If it is below 20 C (68 F), using an infrared light, heat the back door panel and the symbol emblem up to 20 to 30°C (68 to 86°F) and install the symbol emblem.
  
  Fig 3: Identifying Peeling Paper
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
INSTALL RADIATOR GRILLE EMBLEM
1. Engage the 4 claws and install the radiator grille emblem.
  
  Fig 4: Identifying Claws Location
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
INSTALL NO. 2 RADIATOR GRILLE EMBLEM (for Sport Package)
1. Engage the 2 claws and install the No. 2 radiator grille emblem.
  
  Fig 5: Locating Claws And No. 2 Radiator Grille Emblem
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
INSTALL RADIATOR GRILLE NAME PLATE RETAINER (for Sport Package)
1. Install the radiator grille name plate retainer with the 2 screws.
  
  Fig 6: Locating Screws And Radiator Grille Name Plate Retainer
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
INSTALL FRONT BUMPER COVER
1. w/ Fog Light:
  1. Connect the 2 fog light connectors.
  2. Engage the 6 claws and install the front bumper.
    
    Fig 7: Locating Fog Light Connectors
    Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
2. w/o Fog Light:
  1. Engage the 6 claws and install the front bumper.
    
    Fig 8: Identifying Front Bumper Cover
    Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
3. Install the 7 clips.
4. Install the 2 screw grommets.
5. Tighten the 8 screws.
  
  Fig 9: Identifying Screw Grommets And Clips
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
6. Remove the protective tape.
CONNECT CABLE TO NEGATIVE BATTERY TERMINAL (w/ Fog Light)
Torque: 5.4 N*m (55 kgf*cm, 48 in.*lbf)

Fig 10: Applying Protective Tape
Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002