LEMON Manuals: Even more car manuals for everyone
Home >> Toyota >> 2008 >> FJ Cruiser RWD >> Repair and Diagnosis >> External Pages >> Different car >> Section 186 (Door Lock) >> FRONT DOOR LOCK (for Hatchback) >> Inspection

FRONT DOOR LOCK (for Hatchback): Inspection

WARNING: This page is about a different car, the 2008 Toyota Yaris. However, it is still accessible from the selected car via links, so may be relevant.
  1. INSPECT FRONT DOOR LOCK ASSEMBLY LH (w/ Theft Deterrent System) 
    1. Check the resistance of the unlock detection switch.
      1. Using an ohmmeter, measure the resistance and check the results in accordance with the value(s) in the table below.

        Standard Resistance 

        TESTER CONNECTION SPECIFIED CONDITION

        Tester Connection Door Lock Condition Specified Condition
        7-8 Locked 10 kΩ or higher
        7-8 Unlocked Below 1 Ω

        If the result is not as specified, replace the front door lock.

        Fig 1: Inspecting Front Door Lock Assembly LH (W/ Theft Deterrent System)
        G04833279Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Check the resistance of the door lock and unlock switch.
      1. Using an ohmmeter, measure the resistance and check the results in accordance with the value(s) in the table below.

        Standard Resistance 

        TESTER CONNECTION SPECIFIED CONDITION

        Tester Connection Door Lock Condition Specified Condition
        7-9 Locked Below 1 Ω
        7-9 Unlocked 10 kΩ or higher
        7-10 Locked 10 kΩ or higher
        7-10 Unlocked Below 1 Ω

        If the result is not as specified, replace the front door lock.

        Fig 2: Checking Resistance Of Door Lock And Unlock Switch
        G04833280Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  2. INSPECT FRONT DOOR LOCK ASSEMBLY LH (w/o Theft Deterrent System) 
    1. Check the operation.
      1. Apply battery voltage to the front door lock and check the operation of the front door lock motor.

        Standard 

        CONNECTOR TERMINAL REFERENCE CHART

        Measurement Condition Specified Condition
        Battery positive (+) --> Terminal 4
        Battery negative (-) --> Terminal 2        		 Locks
        Battery positive (+) --> Terminal 2
        Battery negative (-) --> Terminal 4        		 Unlocks

        If the result is not as specified, replace the front door lock.

        Fig 3: Inspecting Front Door Lock Assembly LH (W/O Theft Deterrent System)
        G04833281Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Check the resistance of the unlock detection switch.
      1. Using an ohmmeter, measure the resistance and check the results in accordance with the value(s) in the table below.

        Standard Resistance 

        TESTER CONNECTION SPECIFIED CONDITION

        Tester Connection Door Lock Condition Specified Condition
        7-8 Locked 10 kΩ or higher
        7-8 Unlocked Below 1 Ω

        If the result is not as specified, replace the front door lock.

    3. Check the resistance of the door lock and unlock switch.
      1. Using an ohmmeter, measure the resistance and check the results in accordance with the value(s) in the table below.

        Standard Resistance 

        TESTER CONNECTION SPECIFIED CONDITION

        Tester Connection Door Lock Condition Specified Condition
        7-9 Locked Below 1 Ω
        7-9 Unlocked 10 kΩ or higher
        7-10 Locked 10 kΩ or higher
        7-10 Unlocked Below 1 Ω

        If the result is not as specified, replace the front door lock.

        Fig 4: Checking Resistance Of Door Lock And Unlock Switch
        G04833280Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  3. INSPECT FRONT DOOR LOCK ASSEMBLY RH (w/ Theft Deterrent System) 
    1. Check the resistance of the unlock detection switch.
      1. Using an ohmmeter, measure the resistance and check the results in accordance with the value(s) in the table below.

        Standard Resistance 

        TESTER CONNECTION SPECIFIED CONDITION

        Tester Connection Door Lock Condition Specified Condition
        7-8 Locked 10 kΩ or higher
        7-8 Unlocked Below 1 Ω

        If the result is not as specified, replace the front door lock.

        Fig 5: Inspecting Front Door Lock Assembly RH (W/ Theft Deterrent System)
        G04833283Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Check the resistance of the door lock and unlock switch.
      1. Using an ohmmeter, measure the resistance and check the results in accordance with the value(s) in the table below.

        Standard Resistance 

        TESTER CONNECTION SPECIFIED CONDITION

        Tester Connection Door Lock Condition Specified Condition
        6-8 Locked Below 1 Ω
        6-8 Unlocked 10 kΩ or higher
        5-8 Locked 10 kΩ or higher
        5-8 Unlocked Below 1 Ω

        If the result is not as specified, replace the front door lock.

        Fig 6: Checking Resistance Of Door Lock And Unlock Switch
        G04833284Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  4. INSPECT FRONT DOOR LOCK ASSEMBLY RH (w/o Theft Deterrent System) 
    1. Check the operation.
      1. Apply battery voltage to the front door lock and check the operation of the front door lock motor.

        Standard 

        CONNECTOR TERMINAL REFERENCE CHART

        Measurement Condition Specified Condition
        Battery positive (+) --> Terminal 3
        Battery negative (-) --> Terminal 1        		 Locks
        Battery positive (+) -->Terminal 1
        Battery negative (-) --> Terminal 3        		 Unlocks

        If the result is not as specified, replace the front door lock.

        Fig 7: Inspecting Front Door Lock Assembly RH (W/O Theft Deterrent System)
        G04833285Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Check the resistance of the unlock detection switch.
      1. Using an ohmmeter, measure the resistance and check the results in accordance with the value(s) in the table below.

        Standard Resistance 

        TESTER CONNECTION SPECIFIED CONDITION

        Tester Connection Door Lock Condition Specified Condition
        6-7 Locked 10 kΩ or higher
        6-7 Unlocked Below 1 Ω

        If the result is not as specified, replace the front door lock.

    3. Check the resistance of door lock and unlock switch.
      1. Using an ohmmeter, measure the resistance and check the results in accordance with the value(s) in the table below.

        Standard Resistance 

        TESTER CONNECTION SPECIFIED CONDITION

        Tester Connection Door Lock Position Specified Condition
        5-7 Locked Below 1 Ω
        5-7 Unlocked 10 kΩ or higher
        4-7 Locked 10 kΩ or higher
        4-7 Unlocked Below 1 Ω

        If the result is not as specified, replace the front door lock.

scientia non olet · About LEMON Manuals