LEMON Manuals: Even more car manuals for everyone
Home >> Toyota >> 2008 >> FJ Cruiser RWD >> Repair and Diagnosis >> External Pages >> Different car >> Section 140 (Supplemental Restraint System) >> Airbag System >> DTC B1602/83 Lost Communication with Front Satellite Sensor Bus RH; DTC B1603/83 Front Satellite Sensor Bus RH Initialization Incomplete; DTC B1612/83 Lost Communication with Front Airbag Sensor RH; DTC B1613/83 Front Airbag Sensor RH Initialization Incomplete >> Inspection Procedure

Inspection Procedure

WARNING: This page is about a different car, the 2007 Toyota RAV4. However, it is still accessible from the selected car via links, so may be relevant.
  1. CHECK CONNECTION OF CONNECTOR 
    1. Turn the ignition switch OFF.
    2. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
    3. Check that the connectors are properly connected to the center airbag sensor and the front airbag sensor RH.

    OK: The connectors are connected. 

    NG: CONNECT CONNECTOR 

    OK: GO to Next Step 

  2. CHECK FRONT AIRBAG SENSOR RH CIRCUIT (OPEN) 
    1. Disconnect the connectors from the center airbag sensor and the front airbag sensor RH.
    2. Using a service wire, connect A29-2 (+SR) and A29-1 (-SR) of connector E.
      NOTE: Do not forcibly insert a service wire into the terminals of the connector when connecting.
    3. Measure the resistance of the wire harness side connector.

      Standard resistance 

      TESTER CONNECTION AND SPECIFIED CONDITION

      Tester Connection Specified Condition
      E45-29 (+SR) - E45-27 (-SR) Below 1 Ω

    NG: GO to step  7

    Fig 1: Checking Front Airbag Sensor RH Circuit (Open)
    G05184357Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

    OK: GO to Next Step 

  3. CHECK FRONT AIRBAG SENSOR RH CIRCUIT (SHORT) 
    1. Disconnect the service wire from connector E.
    2. Measure the resistance of the wire harness side connector.

      Standard resistance 

      TESTER CONNECTION AND SPECIFIED CONDITION

      Tester Connection Specified Condition
      E45-29 (+SR) - E45-27 (-SR) 1 MΩ or higher

    NG: GO to step  8

    Fig 2: Checking Front Airbag Sensor RH Circuit (Short)
    G05184358Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  4. CHECK FRONT AIRBAG SENSOR RH CIRCUIT (TO B+) 
    1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
    2. Turn the ignition switch ON.
    3. Measure the voltage of the wire harness side connector.

      Standard voltage 

      TESTER CONNECTION AND SPECIFIED CONDITION

      Tester Connection Specified Condition
      E45-29 (+SR) - Body ground Below 1 V
      E45-27 (-SR) - Body ground Below 1 V

    NG: GO to step  9

    Fig 3: Checking Front Airbag Sensor RH Circuit (To B+)
    G05184358Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

    OK: GO to Next Step 

  5. CHECK FRONT AIRBAG SENSOR RH CIRCUIT (TO GROUND) 
    1. Turn the ignition switch OFF.
    2. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
    3. Measure the resistance of the wire harness side connector.

      Standard resistance 

      TESTER CONNECTION AND SPECIFIED CONDITION

      Tester Connection Specified Condition
      E45-29 (+SR) - Body ground 1 MΩ or higher
      E45-27 (-SR) - Body ground 1 MΩ or higher

    NG: GO to step  10

    Fig 4: Checking Front Airbag Sensor RH Circuit (To Ground)
    G05184358Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

    OK: GO to Next Step 

  6. CHECK FRONT AIRBAG SENSOR RH 
    1. Connect the connectors to the center airbag sensor.
    2. Interchange the front airbag sensor RH and LH, and connect the connectors to them.
    3. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
    4. Turn the ignition switch ON, and wait for at least 60 seconds.
    5. Clear the DTCs (see DTC CHECK / CLEAR ).
    6. Turn the ignition switch OFF.
    7. Turn the ignition switch ON, and wait for at least 60 seconds.
    8. Check the DTCs (see DTC CHECK / CLEAR ).

      Result 

      RESULT CHART

      Result Proceed to
      DTC B1602/83, B1603/83, B1612/83, B1613/83, B1607/84, B1608/84, B1617/ 84 and B1618/84 are not output. A
      DTC B1602/83, B1603/83, B1612/83 and B1613/83 are output B
      B1607/84, B1608/84, B1617/84 and B1618/84 are output C
    Fig 5: Checking Front Airbag Sensor RH
    G05184361Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

    HINT:

    DTCs other than DTC B1602/83, B1603/83, B1612/83, B1613/83, B1607/84, B1608/84, B1617/84 and B1618/ 84 may be output at this time, but they are not related to this check.

    B: REPLACE CENTER AIRBAG SENSOR ASSEMBLY 

    C: REPLACE FRONT AIRBAG SENSOR RH 

    A: USE SIMULATION METHOD TO CHECK 

  7. CHECK ENGINE ROOM MAIN WIRE (OPEN) 
    1. Disconnect the service wire from connector E.
    2. Disconnect the engine room main wire connector from the instrument panel wire.
    3. Using a service wire, connect AE9-2 (-SR) and AE9-1 (+SR) of connector D.
      NOTE: Do not forcibly insert a service wire into the terminals of the connector when connecting.
    4. Measure the resistance of the wire harness side connector.

      Standard resistance 

      TESTER CONNECTION AND SPECIFIED CONDITION

      Tester Connection Specified Condition
      A29-2 (+SR) - A29-1 (-SR) Below 1 Ω

    NG: REPAIR OR REPLACE ENGINE ROOM MAIN WIRE 

    Fig 6: Checking Engine Room Main Wire (Open)
    G05184362Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

    OK: REPAIR OR REPLACE INSTRUMENT PANEL WIRE 

  8. CHECK ENGINE ROOM MAIN WIRE (SHORT) 
    1. Disconnect the engine room main wire connector from the instrument panel wire.
    2. Measure the resistance of the wire harness side connector.

      Standard resistance 

      TESTER CONNECTION AND SPECIFIED CONDITION

      Tester Connection Specified Condition
      AE9-1(+SR)-AE9-2(-SR) 1 MΩ or higher

    NG: REPAIR OR REPLACE ENGINE ROOM MAIN WIRE 

    Fig 7: Checking Engine Room Main Wire (Short)
    G05184363Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

    OK: REPAIR OR REPLACE INSTRUMENT PANEL WIRE 

  9. CHECK ENGINE ROOM MAIN WIRE (TO B+) 
    1. Turn the ignition switch OFF.
    2. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
    3. Disconnect the engine room main wire connector from the instrument panel wire.
    4. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
    5. Turn the ignition switch ON.
    6. Measure the voltage of the wire harness side connector.

      Standard voltage 

      TESTER CONNECTION AND SPECIFIED CONDITION

      Tester Connection Specified Condition
      AE9-1 (+SR) - Body ground Below 1 V
      AE9-2 (-SR) - Body ground Below 1 V

    NG: REPAIR OR REPLACE ENGINE ROOM MAIN WIRE 

    Fig 8: Checking Engine Room Main Wire (To B+)
    G05184363Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

    OK: REPAIR OR REPLACE INSTRUMENT PANEL WIRE 

  10. CHECK ENGINE ROOM MAIN WIRE (TO GROUND) 
    1. Disconnect the engine room main wire connector from the instrument panel wire.
    2. Measure the resistance of the wire harness side connector.

      Standard resistance 

      TESTER CONNECTION AND SPECIFIED CONDITION

      Tester Connection Specified Condition
      AE9-1 (+SR) - Body ground 1 MΩ or higher
      AE9-2 (-SR) - Body ground 1 MΩ or higher

    NG: REPAIR OR REPLACE ENGINE ROOM MAIN WIRE 

    Fig 9: Checking Engine Room Main Wire (To Ground)
    G05184363Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

    OK: REPAIR OR REPLACE INSTRUMENT PANEL WIRE 

scientia non olet · About LEMON Manuals