LEMON Manuals: Even more car manuals for everyone
Home >> Toyota >> 2008 >> FJ Cruiser RWD >> Repair and Diagnosis >> External Pages >> Different car >> Section 136 (Mirror) >> Outer Rear View Mirror >> Inspection

Outer Rear View Mirror: Inspection

WARNING: This page is about a different car, the 2007 Toyota RAV4. However, it is still accessible from the selected car via links, so may be relevant.
  1. INSPECT OUTER REAR VIEW MIRROR ASSEMBLY LH 
    1. Disconnect the mirror connector.
    2. Apply battery voltage and check the operation of the mirror.
      Fig 1: Identifying Mirror Connector Terminals
      G04491503Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      OK: Go TO NEXT STEP. 

      REFERENCE CHART

      Measurement Condition Specified Condition
      Battery positive (+) --> Terminal 3 (MV)
      Battery negative (-) --> Terminal 7 (M+)      		 Turns upward (A)
      Battery positive (+) --> Terminal 7 (M+)
      Battery negative (-) --> Terminal 3 (MV)      		 Turns downward (B)
      Battery positive (+) --> Terminal 6 (MH)
      Battery negative (-) --> Terminal 7 (M+)      		 Turns left (C)
      Battery positive (+) --> Terminal 7 (M+)
      Battery negative (-) --> Terminal 6 (MH)      		 Turns right (D)

      If the result is not as specified, replace the mirror assembly.

    3. w/Mirror Heater:

      Check the resistance.

      1. Measure the resistance between the terminals.
        Fig 2: Identifying Power Mirror Connector Terminals
        G04491504Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

        Standard resistance 

        REFERENCE CHART

        Tester connection Condition Specified Condition
        4 (H-) - 5 (H+) 65°C (149°F) 4 to 12 Ω

        If the result is not as specified, replace the outer rear view mirror.

      2. Connect the cable from the negative battery (-) terminal to terminal 5 and the positive battery (+) terminal to terminal 4, then check that the mirror becomes warm.

        OK: Mirror becomes warm. 

        HINT:

        It takes a short time for the mirror to become warm.

        If the result is not as specified, replace the outer rear view mirror.

  2. INSPECT OUTER REAR VIEW MIRROR ASSEMBLY RH 
    1. Disconnect the mirror connector.
    2. Apply battery voltage and check the operation of the mirror.
      Fig 3: Identifying Power Mirror Connector Terminals
      G04491505Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

      OK: Go TO NEXT STEP. 

      REFERENCE CHART

      Measurement Condition Specified Condition
      Battery positive (+) --> Terminal 3 (MV)
      Battery negative (-) --> Terminal 7 (M+)      		 Turns upward (A)
      Battery positive (+) --> Terminal 7 (M+)
      Battery negative (-) --> Terminal 3 (MV)      		 Turns downward (B)
      Battery positive (+) --> Terminal 6 (MH)
      Battery negative (-) --> Terminal 7 (M+)      		 Turns left (D)
      Battery positive (+) --> Terminal 7 (M+)
      Battery negative (-) --> Terminal 6 (MH)      		 Turns right (C)

      If the result is not as specified, replace the mirror assembly.

    3. w/Mirror Heater:

      Check the resistance.

      1. Measure the resistance between the terminals.
        Fig 4: Identifying Power Mirror Connector Terminals
        G04491506Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

        Standard resistance 

        REFERENCE CHART

        Tester connection Condition Specified Condition
        4 (H-) - 5 (H+) 65°C (149°F) 4 to 12 Ω

        If the result is not as specified, replace the outer rear view mirror.

      2. Connect the cable from the negative battery (-) terminal to terminal 5 and the positive battery (+) terminal to terminal 4, then check that the mirror becomes warm.

        OK: Mirror becomes warm. 

        HINT:

        It takes a short time for the mirror to become warm.

        If the result is not as specified, replace the outer rear view mirror.

scientia non olet · About LEMON Manuals