LEMON Manuals: Even more car manuals for everyone
Home >> Toyota >> 2008 >> Camry Base, Automatic >> Repair and Diagnosis >> Suspension >> Wheels & Tire System >> Tire & Wheel (Except Hybrid) >> Tire Pressure Warning System >> DTC C2111/11 Transmitter ID1 Operation Stop; DTC C2112/12 Transmitter ID2 Operation Stop; DTC C2113/13 Transmitter ID3 Operation Stop; DTC C2114/14 Transmitter ID4 Operation Stop; DTC C2115/15 Transmitter ID5 Operation Stop >> Inspection Procedure

Inspection Procedure

  1. PERFORM FORCED TRANSMISSION OF TRANSMITTER ID OF ALL WHEELS 
    1. Set the tire pressure to the specified value (See INSPECTION  ).
    2. Connect Techstream to the DLC3.
    3. Turn the ignition switch on (IG) and turn the tester on.
    4. Enter the following menus:
      1. Select: Chassis / Tire Pressure Monitor / Data List
    5. Check the values by referring to the table below.

      Tire Pressure Monitor 

      TIRE PRESSURE MONITOR DATA LIST

      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      ID1 Tire Inflation Pressure ID1 tire inflation pressure / min.: Absolute pressure / 0 kPa (0 kgf/cm2 , 0 psi), Relative pressure / -100 kPa (-1 kgf/ cm2 , -14 psi) max.: Absolute pressure / 637.5 kPa (6.5 kgf/ cm2 , 92 psi), Relative pressure / 537.5 kPa (5.4 kgf/cm2 , 78 psi) Actual tire inflation pressure If 0 kPa (0 kgf/cm2 , 0 psi) is displayed for absolute pressure or -100 kPa (-1 kgf/cm2 , -14 psi) is displayed for relative pressure, data has not been received.*
      ID2 Tire Inflation Pressure ID2 tire inflation pressure / min.: Absolute pressure / 0 kPa (0 kgf/cm2 , 0 psi), Relative pressure / -100 kPa (-1 kgf/ cm2 , -14 psi) max.: Absolute pressure / 637.5 kPa (6.5 kgf/ cm2 , 92 psi), Relative pressure / 537.5 kPa (5.4 kgf/cm2 , 78 psi) Actual tire inflation pressure If 0 kPa (0 kgf/cm2 , 0 psi) is displayed for absolute pressure or -100 kPa (-1 kgf/cm2 , -14 psi) is displayed for relative pressure, data has not been received.*
      ID3 Tire Inflation Pressure ID3 tire inflation pressure / min.: Absolute pressure / 0 kPa (0 kgf/cm2 , 0 psi), Relative pressure / -100 kPa (-1 kgf/ cm2 , -14 psi) max.: Absolute pressure / 637.5 kPa (6.5 kgf/ cm2 , 92 psi), Relative pressure / 537.5 kPa (5.4 kgf/cm2 , 78 psi) Actual tire inflation pressure If 0 kPa (0 kgf/cm2 , 0 psi) is displayed for absolute pressure or -100 kPa (-1 kgf/cm2 , -14 psi) is displayed for relative pressure, data has not been received.*
      ID4 Tire Inflation Pressure ID4 tire inflation pressure / min.: Absolute pressure / 0 kPa (0 kgf/cm2 , 0 psi), Relative pressure / -100 kPa (-1 kgf/ cm2 , -14 psi) max.: Absolute pressure / 637.5 kPa (6.5 kgf/ cm2 , 92 psi), Relative pressure / 537.5 kPa (5.4 kgf/cm2 , 78 psi) Actual tire inflation pressure If 0 kPa (0 kgf/cm2 , 0 psi) is displayed for absolute pressure or -100 kPa (-1 kgf/cm2 , -14 psi) is displayed for relative pressure, data has not been received.*
      ID5 Tire Inflation Pressure ID5 tire inflation pressure / min.: Absolute pressure / 0 kPa (0 kgf/cm2 , 0 psi), Relative pressure / -100 kPa (-1 kgf/ cm2 , -14 psi) max.: Absolute pressure / 637.5 kPa (6.5 kgf/ cm2 , 92 psi), Relative pressure / 537.5 kPa (5.4 kgf/cm2 , 78 psi) Actual tire inflation pressure If 0 kPa (0 kgf/cm2 , 0 psi) is displayed for absolute pressure or -100 kPa (-1 kgf/cm2 , -14 psi) is displayed for relative pressure, data has not been received.*
      HINT:
      *: It may take about 2 or 3 minutes until the values are displayed. If the values are not displayed after a few minutes, perform troubleshooting according to the inspection procedure for DTCs C2121/21 to C2125/25 (See DTC C2121/21 NO SIGNAL FROM TRANSMITTER ID1 IN MAIN MODE; DTC C2122/22 NO SIGNAL FROM TRANSMITTER ID2 IN MAIN MODE; DTC C2123/23 NO SIGNAL FROM TRANSMITTER ID3 IN MAIN MODE; DTC C2124/24 NO SIGNAL FROM TRANSMITTER ID4 IN MAIN MODE; DTC C2125/25 NO SIGNAL FROM TRANSMITTER ID5 IN MAIN MODE; DTC C2181/81 TRANSMITTER ID1 NOT RECEIVED (TEST MODE DTC); DTC C2182/82 TRANSMITTER ID2 NOT RECEIVED (TEST MODE DTC); DTC C2183/83 TRANSMITTER ID3 NOT RECEIVED (TEST MODE DTC); DTC C2184/84 TRANSMITTER ID4 NOT RECEIVED (TEST MODE DTC); DTC C2185/85 TRANSMITTER ID5 NOT RECEIVED (TEST MODE DTC)  ).
    6. Rapidly reduce the tire pressure for each wheel at least 40 kPa (0.4 kgf/cm2 , 5.8 psi) within 30 seconds.
    7. Check that each tire pressure displayed on Techstream screen has changed.

      OK: 

      Each tire pressure displayed on Techstream screen will change to the value of the tire pressure. 

      NOTE:
      • It takes about 2 or 3 minutes to display the updated tire pressure data.
      • If the "ID Tire Inflation Pressure" data has not changed, reset the tire pressure to the appropriate specified value and rotate the tire 90 to 270°. Then rapidly release the tire pressure and recheck it.
    8. After confirming that all of the tire pressure data displayed on Techstream screen has changed, set the tire pressure to the appropriate specified values.

      HINT:

      If the tire pressure data displayed on Techstream screen has not changed after rechecking, inspect for another problem (malfunction in transmission or reception function) (See DTC C2121/21 NO SIGNAL FROM TRANSMITTER ID1 IN MAIN MODE; DTC C2122/22 NO SIGNAL FROM TRANSMITTER ID2 IN MAIN MODE; DTC C2123/23 NO SIGNAL FROM TRANSMITTER ID3 IN MAIN MODE; DTC C2124/24 NO SIGNAL FROM TRANSMITTER ID4 IN MAIN MODE; DTC C2125/25 NO SIGNAL FROM TRANSMITTER ID5 IN MAIN MODE; DTC C2181/81 TRANSMITTER ID1 NOT RECEIVED (TEST MODE DTC); DTC C2182/82 TRANSMITTER ID2 NOT RECEIVED (TEST MODE DTC); DTC C2183/83 TRANSMITTER ID3 NOT RECEIVED (TEST MODE DTC); DTC C2184/84 TRANSMITTER ID4 NOT RECEIVED (TEST MODE DTC); DTC C2185/85 TRANSMITTER ID5 NOT RECEIVED (TEST MODE DTC)  ).

    NG: Go TO  INSPECTION PROCEDURE   for TRANSMITTER AND RECEIVER INSPECTION PROCEDURE 

    OK: TIRE AND WHEEL - TIRE PRESSURE WARNING SYSTEM 

scientia non olet · About LEMON Manuals