LEMON Manuals: Even more car manuals for everyone
Home >> Toyota >> 2008 >> Camry Base, Automatic >> Repair and Diagnosis >> External Pages >> Different variant/trim >> Section 67 (Engine Control System (2GR-FE Except Hybrid) - System And Circuit Testing, On-Vehicle Inspection, Removal, Inspection And Installation) >> Camshaft Timing Oil Control Valve Assembly >> Installation

Camshaft Timing Oil Control Valve Assembly: Installation

WARNING: This page is about a different variant/trim than selected.
  1. INSTALL CAMSHAFT TIMING OIL CONTROL VALVE (for Bank 2 Intake Side) 
    1. Apply a light coat of engine oil to a new O-ring and install it to the camshaft timing oil control valve.
      Fig 1: Locating Camshaft Timing Oil Control Valve O-Ring
      G04973350Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Install the camshaft timing oil control valve with the bolt.

      Torque: 10 N*m (102 kgf*cm, 7 ft.*lbf) 

      NOTE: Make sure that the O-ring is not cracked or jammed when installing the oil control valve.
    3. Connect the camshaft timing oil control valve connector.
      Fig 2: Locating Camshaft Timing Oil Control Valve Bolt
      G04973850Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  2. INSTALL CAMSHAFT TIMING OIL CONTROL VALVE (for Bank 2 Exhaust Side) 
    1. Apply a light coat of engine oil to a new O-ring and install it to the camshaft timing oil control valve.
      Fig 3: Locating Camshaft Timing Oil Control Valve O-Ring (For Bank 2 Exhaust Side)
      G04973350Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Install the camshaft timing oil control valve with the bolt.

      Torque: 10 N*m (102 kgf*cm, 7 ft.*lbf) 

      NOTE: Make sure that the O-ring is not cracked or jammed when installing the oil control valve.
    3. Connect the camshaft timing oil control valve connector.
      Fig 4: Locating Camshaft Timing Oil Control Valve With Bolt
      G04973849Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  3. INSTALL CAMSHAFT TIMING OIL CONTROL VALVE (for Bank 1 Intake Side) 
    1. Apply a light coat of engine oil to a new O-ring and install it to the camshaft timing oil control valve.
      Fig 5: Identifying Camshaft Timing Oil Control Valve O-Ring (For Bank 1 Intake Side)
      G04973350Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Install the camshaft timing oil control valve with the bolt.

      Torque: 10 N*m (102 kgf*cm, 7 ft.*lbf) 

      NOTE: Make sure that the O-ring is not cracked or jammed when installing the oil control valve.
    3. Connect the camshaft timing oil control valve connector.
      Fig 6: Locating Camshaft Timing Oil Control Valve Bolt
      G04973848Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  4. INSTALL CAMSHAFT TIMING OIL CONTROL VALVE (for Bank 1 Exhaust Side) 
    1. Apply a light coat of engine oil to a new O-ring and install it to the camshaft timing oil control valve.
      Fig 7: Locating Camshaft Timing Oil Control Valve O-Ring (For Bank 1 Exhaust Side)
      G04973350Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Install the camshaft timing oil control valve with the bolt.

      Torque: 10 N*m (102 kgf*cm, 7 ft.*lbf) 

      NOTE: Make sure that the O-ring is not cracked or jammed when installing the oil control valve.
    3. Connect the camshaft timing oil control valve connector.
      Fig 8: Locating Camshaft Timing Oil Control Valve Bolt
      G04973847Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  5. INSTALL INTAKE AIR SURGE TANK  (See INSTALLATION )
  6. INSTALL NO. 1 AIR CLEANER INLET  (See INSTALLATION )
  7. INSTALL AIR CLEANER CASE SUB-ASSEMBLY  (See INSTALLATION )
  8. INSTALL AIR CLEANER CAP SUB-ASSEMBLY (See  INSTALLATION   ) 
  9. INSTALL AIR CLEANER INLET ASSEMBLY  (See INSTALLATION )
  10. INSTALL V-BANK COVER SUB-ASSEMBLY  (See INSTALLATION )
  11. INSTALL COOL AIR INTAKE DUCT SEAL  (See INSTALLATION )
  12. INSTALL COWL TOP PANEL OUTER SUB-ASSEMBLY 
    1. Install the cowl top panel outer sub-assembly with the 4 bolts and 4 nuts.

      Torque: 

      Bolt 

      5.0 N*m (51 kgf*cm, 44 in.*lbf) 

      Nut 

      85 N*m (867 kgf*cm, 63 ft.*lbf) 

      Fig 9: Locating Cowl Top Panel Outer Sub-Assembly Bolts And Nuts
      G04973390Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  13. INSTALL WINDSHIELD WIPER MOTOR AND LINK  (See INSTALLATION )
  14. INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY  (See INSTALLATION )
  15. INSTALL FRONT FENDER TO COWL SIDE SEAL RH  (See INSTALLATION )
  16. INSTALL FRONT FENDER TO COWL SIDE SEAL LH  (See INSTALLATION )
  17. INSTALL WINDSHIELD WIPER ARM AND BLADE ASSEMBLY LH  (See INSTALLATION )
  18. INSTALL WINDSHIELD WIPER ARM AND BLADE ASSEMBLY RH  (See INSTALLATION )
  19. ADD ENGINE COOLANT  (See ON-VEHICLE INSPECTION )
  20. CHECK FOR ENGINE COOLANT LEAKS  (See ON-VEHICLE INSPECTION )
  21. INSTALL ENGINE UNDER COVER RH 
  22. INSTALL ENGINE UNDER COVER LH 
scientia non olet · About LEMON Manuals