Data List / Active Test

Data List

Using Techstream to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

Warm up the engine.
Ignition switch off.
Connect Techstream to the DLC3.
Ignition switch on (IG).
Turn the tester on.
Enter the following menus:
1. For Combination Meter: Body Electrical / Combination Meter / Data List.
2. For ABS/TRAC/VSC: Chassis / ABS/VSC/TRAC / Data List.
3. For Engine and ECT: Powertrain / Engine and ECT / Data List.

Check values by referring to the table below.

Combination Meter:

DATA LIST - COMBINATION METER

Tester Display

Measurement Item/Range

Normal Condition

Diagnostic Note

Tail Cancel SW

Tail cancel switch is OFF/ON

OFF: Turn the light control rheostat knob is not fully downwards

ON: Turn the light control rheostat knob fully upwards

ODO/TRIP Change SW

ODO/TRIP switch is OFF/ON

OFF: Switch is released

ON: Switch is pushed

P-Seatbelt Buckle SW

Front passenger side buckle switch is OFF/ON

OFF: Seat belt is fastened

ON: Seat belt is unfastened

Vehicle Speed Meter

Vehicle speed/Min.: 0 km/h (0 mph), Max.: 255 km/h (158 mph)

Almost same as actual vehicle speed (When driving)

Engine Rpm

Engine speed/Min.: 0 rpm, Max.: 12750 rpm

Almost same at the meter rpm (When engine is running)

Coolant Temperature

Engine coolant temperature: 0°C (32°F) to 127.5°C (261.5°F)

After warming up: 80 to 95°C (176 to 203°F)

Washer Switch

Washer level switch is OFF/ON

OFF: Washer level is not low

ON: Washer level is low

Multi Display Select Switch

MODE switch in the steering pad is OFF/ON

OFF: Mode switch is OFF

ON: Mode switch is ON

+B Voltage Value

Battery voltage/Min.: 0 V, Max.: 25.5 V

10 to 14 V

Integrated value for Oil Maintenance (⁽¹⁾)

Oil maintenance warning value: Min.: 0, Max. 25500 (mile)

The running distance after performing oil maintenance resetting procedure is displayed

If the value is 5000 (mile) or more, perform oil maintenance resetting procedure after changing the oil

Fuel Input

Fuel input signal Min.: 0, Max. 255

Fuel gauge indicates (F): 35

Fuel gauge indicates (3/4): 85

Fuel gauge indicates (1/2): 145

Fuel gauge indicates (3/4): 186

Fuel gauge indicates (E): 205

Ambient Temperature

Outside temperature: Min.: -40°C (-40°F) to 50°C (122°F)

Almost same as actual outside temperature

The temperature displayed on the multi-information display is -40 to 50°C (-40 to 122°F)

Rheostat value

Light Control Rheostat/Min.: 0%, Max.: 100%

Light control rheostat switch is Dark (0%) → Bright (100%)

Quantity of Outside Light

Quantity of outside light/Min.: 0%, Max.: 100%

Outside light is Dark (0%) → Bright (100%)

Communication ECM/Meter DTC 1 to 3

Communication error: not occurred/occurred

Unrec: No Error has occurred

Rec: Error has occurred

ECM ODO (History 1 to 3)

Distance when DTC is output Min.: 0, Max.: 999999

Communication ABS/Meter DTC 1 to 3

Communication error: not occurred/occurred

Unrec: No Error has occurred

Rec: Error has occurred

ABS/VSC ODO (History 1 to 3)

Distance when DTC is output Min.: 0, Max.: 999999

Key Remind Sound

The cycle of the key reminder warning buzzer is displayed

The cycle of the key reminder warning buzzer is Large, Medium, Small

Seat-belt Warning Buzzer

The condition of the driver side seat belt warning buzzer

ON: The driver side seat belt warning buzzer sounds at the vehicle speed is 20 km/h (12 mph) or more when the driver side seat belt is unfastened

OFF: The driver side seat belt warning buzzer does not sound at the vehicle speed is 20 km/h (12 mph) or more when the driver side seat belt is unfastened

Key Remind Volume

The volume of the key reminder warning buzzer is displayed

The volume of the key reminder warning buzzer is Fast, Normal, Slow

Number of Trouble Code

The number of the DTC which is currently output

⁽¹⁾	For U.S.A.

ABS/TRAC/VSC:

DATA LIST - ABS/TRAC/VSC

Tester Display	Measurement Item/Range	Normal Condition	Diagnostic Note
FR/FL/RR/RL Wheel Speed	Vehicle speed/Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph)	Almost same as actual vehicle speed (When driving)	-
Vehicle Speed	Vehicle speed/Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph)	Almost same as actual vehicle speed (When driving)	-

Engine and ECT:

DATA LIST - ENGINE AND ECT

Tester Display	Measurement Item/Range	Normal Condition	Diagnostic Note
Engine Speed	Vehicle speed/Min.: 0 rpm, Max.: 16383.75 rpm	Almost same as actual engine speed (When engine running)	-
Coolant Temp	Engine coolant temperature: Min.: -40°C (-40°F), Max: 140°C (284°F)	80 to 100°C (176 to 212°F): After warming up	If -40°C (-40°F): sensor circuit open If 140°C (284°F) or more: sensor circuit shorted

Active Test

Using Techstream to perform Active Tests allows the relay, actuator, and other items to operate without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Test early in troubleshooting is one way to save diagnostic time. Data List information can be display while performing Active Test.

Connect Techstream to the DLC3.
Ignition switch on (IG).
Turn the tester on.
Enter the following menus: Body Electrical / Combination Meter / Active Test.

Check the operation by referring to the table below.

Combination Meter:

ACTIVE TEST - COMBINATION METER

Tester Display

Test Part

Control Range

Diagnostic Note

Speed Meter Operation

Speedometer

0, 40, 80, 120 mph (⁽¹⁾)

0, 40, 80, 120, 160, 200, 240 km/h (⁽²⁾)

Tacho Meter Operation

Tachometer

0, 1000, 2000, 3000, 4000, 5000, 6000, 7000 (rpm)

Fuel Meter Operation

Fuel receiver gauge

EMPTY, 1/2, FULL