Parking Brake Assembly: Disassembly

HINT:

• Use the same procedures for the RH side and the LH side.
• The procedures listed below are for the LH side.

1. REMOVE REAR WHEEL 
2. SEPARATE REAR DISC BRAKE CALIPER ASSEMBLY 
   1. Remove the 2 bolts and separate the rear disc brake caliper assembly.

      HINT:

      Do not disconnect the flexible hose from the disc brake caliper assembly.

      Fig 1: Locating Rear Disc Brake Caliper Assembly Bolts

      Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
3. REMOVE REAR DISC 
   1. Release the parking brake and place the matchmarks on the rear disc and the axle hub.
   2. Remove the rear disc.

      HINT:

      If the disc cannot be removed easily, turn the shoe adjuster until the wheel turns freely.

      Fig 2: Identifying Matchmarks On Rear Disc And Axle Hub

      Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
4. REMOVE PARKING BRAKE SHOE RETURN TENSION NO. 1 SPRING 
   1. Using needle-nose pliers, remove the 2 parking brake shoe return tension No. 1 springs.
      Fig 3: Locating Parking Brake Shoe Strut Compression Spring

      Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
5. REMOVE PARKING BRAKE SHOE STRUT 
   1. Remove the parking brake shoe strut and the parking brake shoe strut compression spring.
6. REMOVE NO. 1 PARKING BRAKE SHOE ASSEMBLY 
   1. Release the claw of the parking brake shoe hold down spring No. 1 cup.
   2. Remove the No. 1 parking brake shoe assembly as shown in the illustration.
      Fig 4: Removing No. 1 Parking Brake Shoe Assembly

      Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
   3. Remove the parking brake shoe hold down spring No. 1 cup, the parking brake shoe hold down spring, the parking brake shoe hold down spring No. 2 cup, and the parking brake shoe hold down spring No. 1 pin.
7. REMOVE PARKING BRAKE SHOE ADJUSTING SCREW SET 
   1. Remove the parking brake shoe adjusting screw set.
   2. Remove the parking brake shoe return tension No. 2 spring.
      Fig 5: Identifying Parking Brake Shoe Return Tension No. 2 Spring

      Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
8. REMOVE NO. 2 PARKING BRAKE SHOE ASSEMBLY 
   1. Release the claw of the parking brake shoe hold down spring No. 1 cup.
   2. Remove the No. 2 parking brake shoe assembly as shown in the illustration.
      Fig 6: Removing No. 2 Parking Brake Shoe Assembly

      Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
   3. Remove the parking brake shoe hold down spring No. 1 cup, the parking brake shoe hold down spring, the parking brake shoe hold down spring No. 2 cup, and the parking brake shoe hold down spring No. 2 pin.
   4. Using needle-nose pliers, disconnect the No. 3 parking brake cable assembly from the parking brake shoe lever.
   NOTE: Be careful not to damage the No. 3 parking brake cable assembly.
   Fig 7: Disconnecting No. 3 Parking Brake Cable Assembly

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
9. REMOVE PARKING BRAKE SHOE LEVER 
   1. Using a screwdriver, remove the C-washer, shim and the parking brake shoe lever.
      Fig 8: Locating C-Washer

      Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
10. REMOVE PARKING BRAKE SHOE GUIDE PLATE 
    1. Remove the parking brake shoe guide plate set bolt and the parking brake shoe guide plate.
       Fig 9: Removing Parking Brake Shoe Guide Plate

       Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002