LEMON Manuals: Even more car manuals for everyone
Home >> Toyota >> 2008 >> Camry Base, Automatic >> Repair and Diagnosis >> Accessories & Equipment >> Interior/Exterior Trim >> Exterior (Except Hybrid) >> Rear Bumper >> Disassembly

Rear Bumper: Disassembly

  1. REMOVE REAR LOWER SPOILER (w/ Rear Lower Spoiler) 
    1. Remove the 2 screws, 4 nuts and 16 clips.
      Fig 1: Identifying Rear Lower Spoiler Screws, Nuts And Clips (W/ Rear Lower Spoiler)
      G04981916Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Disengage the 16 claws and remove the rear lower spoiler.
  2. REMOVE REAR BUMPER EXTENSION LH (w/ Rear Lower Spoiler) 
    1. Remove the 2 nuts and rear bumper extension LH.
      Fig 2: Identifying Rear Bumper Extension Nuts (W/ Rear Lower Spoiler)
      G04981917Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  3. REMOVE REAR BUMPER EXTENSION RH (w/ Rear Lower Spoiler) 
  4. REMOVE REAR BUMPER PLATE LH 
  5. REMOVE REAR BUMPER PLATE RH 
  6. REMOVE REAR BUMPER PAD 
    1. Remove the rear bumper pad.

      HINT:

      Use the same procedures for the RH side and LH side.

      Fig 3: Identifying Rear Bumper Pad
      G04981918Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  7. REMOVE REAR BUMPER SIDE SUPPORT LH 
    1. Remove the 2 screws.
    2. Disengage the 3 claws and remove the rear bumper side support LH.
      Fig 4: Identifying Rear Bumper Side Support LH Claws And Screws
      G04981919Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  8. REMOVE REAR BUMPER SIDE SUPPORT RH 
  9. REMOVE REAR BUMPER SIDE RETAINER LH 
    1. Remove the 2 screws.
    2. Disengage the 3 claws and remove the rear bumper side retainer LH.
      Fig 5: Identifying Rear Bumper Side Retainer Claws And Screws LH
      G04981920Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  10. REMOVE REAR BUMPER SIDE RETAINER RH 
  11. REMOVE WHEEL HOUSE REINFORCEMENT LH 
    1. Remove the nut and wheel house reinforcement LH.
      Fig 6: Identifying Wheel House Reinforcement Nut LH
      G04981921Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  12. REMOVE WHEEL HOUSE REINFORCEMENT RH 
  13. REMOVE REAR BUMPER ENERGY ABSORBER 
    1. Remove the 4 bolts.
    2. Disengage the 4 claws and remove the rear bumper energy absorber.
      Fig 7: Identifying Rear Bumper Energy Absorber Claws And Bolts
      G04981922Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  14. REMOVE REAR BUMPER BAR 
    1. Remove the rear bumper bar from the rear bumper energy absorber.
      Fig 8: Identifying Rear Bumper Bar
      G04981923Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
  15. REMOVE REAR BUMPER REINFORCEMENT SUB-ASSEMBLY 
    1. Remove the 6 nuts and rear bumper reinforcement sub-assembly.
      Fig 9: Identifying Identifying Rear Bumper Bar Nuts
      G04981924Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
scientia non olet · About LEMON Manuals