REAR NO. 1 SEAT ASSEMBLY (w/o Rear No. 2 Seat for LH Side): Disassembly

1. Remove the 2 screws.
2. Disengage the claw and remove the rear seat cushion molding LH as shown in the illustration.
   Fig 1: Locating Claw And Rear Seat Cushion Molding LH

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

1. Remove the 3 screws.
2. Disengage the 3 claws and remove the rear seat cushion molding rear LH.
   Fig 2: Identifying Claws And Screws Of Rear Seat Cushion Molding Rear LH

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

1. Using a "Torx" socket wrench (T45), remove the 2 "Torx" bolts.
2. Release the 2 rubber bands on the backside of the rear seatback board carpet assembly.
3. Remove the hog rings.
4. Remove the 2 bolts and separate type rear seat cushion assembly.

1. Disengage the hooks and remove the hog rings and rear seat cushion frame sub-assembly.

1. Remove the hog rings and separate type rear seat cushion cover.

1. Remove the 2 screws and 2 tonneau cover hook holders.

1. Using a molding remover, disengage the 4 claws and remove the rear seatback cover.
   Fig 3: Identifying Claws Of Rear Seatback Cover

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

1. Disengage the 4 clips and remove the rear seatback board carpet assembly.
   Fig 4: Identifying Clips Of Rear Seatback Board Carpet Assembly

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

1. Using a screwdriver, disengage the 2 claws and remove the rear seatback lock striker cover.

   HINT:

   Tape the screwdriver tip before use.

1. Remove the 2 screws.
Fig 5: Identifying Screws
Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
2. Disconnect the rear seat reclining control No.2 cable and remove the rear seat lock control lever sub-assembly.

1. Disengage the 2 claws and remove the rear seat headrest support (LH side).
   Fig 6: Locating Hog Rings

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

HINT:

Use the same procedures described for the LH side.

1. Disengage the hooks and remove the hog rings and separate type rear seatback cover with pad.

1. Remove the hog rings and separate type rear seatback cover.

1. Remove the bolt and fold seat stopper band assembly No.2.

1. Remove the screw.
2. Remove the rear seat reclining cover inner LH as shown in the illustration.
   Fig 7: Locating Rear Seat Reclining Cover Inner LH

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

1. Remove the screw and rear seat cover No.2.

1. Disengage the 2 cables and remove the rear seat reclining control No.2 cable.

1. Using a "Torx" socket wrench (T45), remove the 4 "Torx" bolts and rear seatback frame sub-assembly.

1. Remove the clamp.
2. Disengage the 2 seat track stop plate cables.
3. Remove the 2 nuts and seat track stop plate.

1. Remove the E-ring and spring.
2. Remove the 4 nuts and reclining control link sub-assembly.

1. Using a "Torx" socket wrench (T45), remove the 5 "Torx" bolts and rear seatback frame sub-assembly lower.

1. Remove the 4 nuts and 2 fold seat cushion frames No.1.

1. Move the rear seat track assembly outer and rear seat track assembly inner fully forward by operating the rear seat track adjusting handle.
Fig 8: Locating Rear Seat Track Adjusting Handle
Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
2. Using a hexagon wrench 1.5 mm (0.059 in.), push down the 2 handle stoppers as shown in the illustration and remove the rear seat track adjusting handle.