Power Seat Switch: Inspection
- INSPECT FRONT POWER SEAT SWITCH
- Inspect the driver side power seat switch.
- Measure the resistance according to the value(s) in the table below.
Resistance: Slide switch
SLIDE SWITCH RESISTANCE SPECIFICATIONTester Connection Switch Condition Specified Condition 1(B) - 9(SLDF) FRONT Below 1 Ω 4(E) - 6(SLDR) FRONT Below 1 Ω 4(E) - 6(SLDR) OFF Below 1 Ω 4(E) - 9(SLDF) OFF Below 1 Ω 1(B) - 6(SLDR) REAR Below 1 Ω 4(E) - 9(SLDF) REAR Below 1 Ω Front vertical switch
FRONT VERTICAL SWITCH RESISTANCE SPECIFICATIONTester Connection Switch Condition Specified Condition 1(B) - 10(FUP) UP Below 1 Ω 4(E) - 5(FDWN) UP Below 1 Ω 4(E) - 5(FDWN) OFF Below 1 Ω 4(E) - 10(FUP) OFF Below 1 Ω 1(B) - 5(FDWN) DOWN Below 1 Ω 4(E) - 10(FUP) DOWN Below 1 Ω Lifter switch
LIFTER SWITCH RESISTANCE SPECIFICATIONTester Connection Switch Condition Specified Condition 1(B) - 7(LUP) UP Below 1 Ω 4(E) - 8(LDWN) UP Below 1 Ω 4(E) - 7(LUP) OFF Below 1 Ω 4(E) - 8(LDWN) OFF Below 1 Ω 1(B) - 8(LDWN) DOWN Below 1 Ω 4(E) - 7(LUP) DOWN Below 1 Ω Reclining switch
RECLINING SWITCH RESISTANCE SPECIFICATIONTester Connection Switch Condition Specified Condition 1(B) - 3(RCLF) FRONT Below 1 Ω 2(RCLR) - 4(E) FRONT Below 1 Ω 2(RCLR) - 4(E) OFF Below 1 Ω 3(RCLF) - 4(E) OFF Below 1 Ω 1(B) - 2(RCLR) REAR Below 1 Ω 3(RCLF) - 4(E) REAR Below 1 Ω If the result is not as specified, replace the switch.
- Measure the resistance according to the value(s) in the table below.
- Inspect the front passenger side power seat switch.
- Measure the resistance according to the value(s) in the table below.
Resistance: Slide switch
SLIDE SWITCH RESISTANCE SPECIFICATIONTester Connection Switch Condition Specified Condition 1(B) - 9(SLDF) FRONT Below 1 Ω 4(E) - 6(SLDR) FRONT Below 1 Ω 4(E) - 6(SLDR) OFF Below 1 Ω 4(E) - 9(SLDF) OFF Below 1 Ω 1(B) - 6(SLDR) REAR Below 1 Ω 4(E) - 9(SLDF) REAR Below 1 Ω Reclining switch
RECLINING SWITCH RESISTANCE SPECIFICATIONTester Connection Switch Condition Specified Condition 1(B) - 3(RCLF) FRONT Below 1 Ω 2(RCLR) - 4(E) FRONT Below 1 Ω 2(RCLR) - 4(E) OFF Below 1 Ω 3(RCLF) - 4(E) OFF Below 1 Ω 1(B) - 2(RCLR) REAR Below 1 Ω 3(RCLF) - 4(E) REAR Below 1 Ω If the result is not as specified, replace the switch.
- Measure the resistance according to the value(s) in the table below.
- Inspect the driver side power seat switch.