LEMON Manuals: Even more car manuals for everyone
Home >> Toyota >> 2007 >> Highlander Hybrid Limited, AWD >> Repair and Diagnosis >> Accessories & Equipment >> Seats >> Seat (Hybrid) >> FRONT SEAT ASSEMBLY (for Power Seat) >> Reassembly

FRONT SEAT ASSEMBLY (for Power Seat): Reassembly

  1. INSTALL FRONT SEAT ADJUSTER SUB-ASSEMBLY 
  2. INSTALL FRONT SEAT SIDE AIRBAG ASSEMBLY (w/ Front Seat Side Airbag) 
    1. Install the front seat side airbag assembly with the 2 nuts.

      Torque: 5.5 N*m (56 kgf*cm, 49 in.*lbf) 

    2. Install the clamp.
  3. INSTALL FRONT SEAT WIRE 
  4. INSTALL OCCUPANT CLASSIFICATION ECU (for Front Passenger Seat)  (See INSTALLATION )
  5. INSTALL SEAT POSITION SENSOR (for Driver Seat)  (See INSTALLATION )
  6. INSTALL SEAT SLIDE POSITION SENSOR PROTECTOR (for Driver Seat) 
  7. INSTALL LUMBAR SUPPORT ADJUSTER ASSEMBLY (for Driver Seat) 
  8. INSTALL FRONT SEAT CUSHION SHIELD LOWER RH 
  9. INSTALL FRONT SEAT CUSHION SHIELD LOWER LH 
  10. INSTALL RECLINING ADJUSTER INSIDE COVER RH 
  11. INSTALL RECLINING ADJUSTER INSIDE COVER LH 
  12. INSTALL RH SEAT RECLINING ADJUSTER INSIDE COVER 
  13. INSTALL LH SEAT RECLINING ADJUSTER INSIDE COVER 
  14. INSTALL SEPARATE TYPE FRONT SEATBACK PAD (w/o Front Seat Side Airbag) 
  15. INSTALL SEPARATE TYPE FRONT SEATBACK COVER 
    1. Using hog ring pliers, install the separate type front seatback cover to the separate type front seatback pad with new hog rings.
      Fig 1: Installing Separate Type Front Seatback Cover To Separate Type Front Seatback Pad With New Hog Rings
      G05244023Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      NOTE:
      • Be careful not to damage the cover.
      • When installing the hog rings, take care to minimize wrinkles as much as possible.
  16. INSTALL SEPARATE TYPE FRONT SEATBACK COVER WITH PAD 
    1. Install the separate type front seatback cover with pad to the separate type front seat cushion spring assembly.
    2. With front seat side airbag:
      1. Install the separate type front seatback cover bracket with nut.
        Fig 2: Identifying Separate Type Front Seatback Cover Bracket With Nut
        G05244024Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

        Torque: 5.6 N*m (57 kgf*cm, 50 in.*lbf) 

        NOTE:
        • For vehicles with side airbags, the side airbags may not deploy properly unless the separate type front seatback cover is securely installed.
        • Check that the strap is not twisted after installing the bracket.
        • Install the bracket securely.
    3. Install the hook.
  17. INSTALL FRONT SEAT HEADREST SUPPORT 
  18. INSTALL FRONT SEAT HEADREST SUPPORT 
  19. INSTALL FRONT SEATBACK BOARD COVER SUB-ASSEMBLY 
  20. INSTALL FRONT SEATBACK BOARD SUB-ASSEMBLY 
  21. INSTALL SEAT ARMREST ASSEMBLY 
    1. Install the seat armrest assembly with the bolt.

      Torque: 37 N*m (377 kgf*cm, 27 ft.*lbf) 

  22. INSTALL SEAT ARMREST COVER 
  23. INSTALL FRONT SEAT HEADREST ASSEMBLY 
  24. INSTALL SEPARATE TYPE FRONT SEAT CUSHION PAD 
  25. INSTALL SEPARATE TYPE FRONT SEAT CUSHION COVER 
    1. Using hog ring pliers, install the separate type front seat cushion cover to the separate type front seat cushion pad with new hog rings.
      Fig 3: Installing Separate Type Front Seatback Cover To Separate Type Front Seatback Pad With New Hog Rings
      G05244023Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      NOTE:
      • Be careful not to damage the cover.
      • When installing the hog rings, take care to minimize wrinkles as much as possible.
  26. INSTALL SEPARATE TYPE FRONT SEAT CUSHION COVER WITH PAD 
  27. INSTALL FRONT SEAT INNER BELT ASSEMBLY 
  28. INSTALL FRONT POWER SEAT SWITCH 
  29. INSTALL FRONT SEAT CUSHION SHIELD INNER NO.1 
  30. INSTALL FRONT SEAT CUSHION SHIELD INNER 
  31. INSTALL FRONT SEAT CUSHION SHIELD 
  32. INSTALL POWER SEAT SWITCH ASSEMBLY (for Driver Seat) 
  33. INSTALL FRONT SEAT CUSHION SHIELD ASSEMBLY 
  34. INSTALL SLIDE AND VERTICAL POWER SEAT SWITCH KNOB 
  35. INSTALL RECLINING POWER SEAT SWITCH KNOB 
scientia non olet · About LEMON Manuals