LEMON Manuals: Even more car manuals for everyone
Home >> Toyota >> 2006 >> Corolla LE, Automatic >> Repair and Diagnosis >> Brakes >> Traction Control >> Brakes - Abs With EBD (Diagnostics) >> TC Terminal Circuit >> Inspection Procedure

Inspection Procedure

  1. INSPECT DLC3 TERMINAL VOLTAGE (TC TERMINAL) 
    1. Turn the ignition switch to the ON position.
    2. Measure the voltage according to the value(s) in DLC3 TERMINALS VOLTAGE  .

      Standard: 

      DLC3 TERMINALS VOLTAGE

      Tester Connection Condition Specified Condition
      D1-13 (TC) - D1-4 (CG) IG switch ON 11 to 14 V
      Fig 1: Inspecting DLC3 Terminal Voltage (TC Terminal)
      G02599656Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    1. NG: Go to step   3 
    2. OK: GO TO NEXT STEP. 
  2. CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - DLC3) 
    1. Disconnect the skid control ECU connector.
    2. Measure the resistance according to the value(s) in SKID CONTROL ECU AND DLC3 TERMINALS RESISTANCE  .

      Standard: 

      SKID CONTROL ECU AND DLC3 TERMINALS RESISTANCE

      Tester Connection Specified Condition
      S1-21 (TC) - D1-13 (TC) Below 1 Ω
    3. Measure the resistance according to the value(s) in SKID CONTROL ECU TERMINALS AND BODY GROUND RESISTANCE  .

      Standard: 

      SKID CONTROL ECU TERMINALS AND BODY GROUND RESISTANCE

      Tester Connection Specified Condition
      S1-2 (TC) - Body ground 10 kΩ or higher
      Fig 2: Checking Harness And Connector (Skid Control ECU - DLC3)
      G02599657Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    1. NG: REPAIR OR REPLACE HARNESS OR CONNECTOR (TC CIRCUIT) 
    2. OK: REPLACE BRAKE ACTUATOR ASSY (SEE  REPLACEMENT  ) 
  3. CHECK HARNESS AND CONNECTOR (DLC3 - BODY GROUND) 
    1. Measure the resistance according to the value(s) in DLC3 TERMINALS AND BODY GROUND RESISTANCE  .

      Standard: 

      DLC3 TERMINALS AND BODY GROUND RESISTANCE

      Tester Connection Specified Condition
      D1-4 (CG) - Body ground Below 1 Ω
      Fig 3: Checking Harness And Connector (DLC3 - Body Ground)
      G02599658Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    1. NG: REPAIR OR REPLACE HARNESS OR CONNECTOR(GND CIRCUIT) 
    2. OK: GO TO NEXT STEP. 
  4. CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - DLC3) 
    1. Disconnect the skid control ECU connector.
    2. Measure the resistance according to the value(s) in SKID CONTROL ECU AND DLC3 TERMINALS RESISTANCE  .

      Standard: 

      SKID CONTROL ECU AND DLC3 TERMINALS RESISTANCE

      Tester Connection Specified Condition
      S1 - 21 (TC) - D1 - 13 (TC) Below 1 Ω
    3. Measure the resistance according to the value(s) in SKID CONTROL ECU TERMINALS AND BODY GROUND RESISTANCE  .

      Standard: 

      SKID CONTROL ECU TERMINALS AND BODY GROUND RESISTANCE

      Tester Connection Specified Condition
      S1-21 (TC) - Body ground 10 kΩ or higher
      Fig 4: Checking Harness And Connector (Skid Control ECU - DLC3)
      G02599659Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    1. NG: REPAIR OR REPLACE HARNESS OR CONNECTOR (TC CIRCUIT) 
    2. OK: REPLACE BRAKE ACTUATOR ASSY (SEE  REPLACEMENT  ) 
scientia non olet · About LEMON Manuals