Torque Specifications: 2ZZ-GE:
WARNING: This page is about a different car, the 2005 Toyota Corolla. However, it is still accessible from the selected car via links, so may be relevant.
TORQUE SPECIFICATIONS - 2ZZ-GE
| Part Tightened | N.m | kgf.cm | ft.lbf |
|---|---|---|---|
| Cylinder head cover No. 2 at Cylinder head cover sub-assy | 7.0 | 71 | 62 in.lbf |
| Suction hose bracket at Body | 9.8 | 100 | 87 in.lbf |
| Cylinder head cover sub-assy at Cylinder head sub-assy | 10 | 102 | 7 |
| Union to connector tube hose clamp at Cylinder head cover sub-assy | 7.0 | 71 | 62 in.lbf |
| Fuel tube clamp at Cylinder head cover sub-assy | 7.5 | 76 | 66 in.lbf |
| Wire harness protector at Cylinder head cover sub-assy | 9.0 | 92 | 80 in.lbf |
| Ventilation No. 1 tube at Cylinder head cover sub-assy | 10 | 102 | 7 |
| Ventilation No. 1 tube at Intake manifold | 24 | 245 | 18 |
| Ignition coil assy at Cylinder head cover sub-assy | 9.0 | 92 | 80 in.lbf |
| Engine hanger at Cylinder head sub-assy | 38 | 387 | 28 |
| Engine coolant temperature sensor at Cylinder head sub-assy | 20 | 204 | 15 |
| Camshaft position sensor at Cylinder head sub-assy | 9.0 | 92 | 80 in.lbf |
| Knock sensor at Cylinder block sub-assy | 20 | 204 | 15 |
| Oil pressure switch assy at Cylinder head sub-assy | 15 | 153 | 11 |
| Engine oil pressure switch assy at Crankshaft bearing cap sub-assy | 15 | 153 | 11 |
| Crankshaft position sensor at Timing chain or belt cover sub-assy | 9.0 | 92 | 80 in.lbf |
| Water by-pass pipe No. 1 at Cylinder block sub-assy Nut | 10 | 102 | 7 |
| Water by-pass pipe No. 1 at Cylinder block sub-assy Bolt | 8.5 | 87 | 75 in.lbf |
| Water by-pass pipe No. 1 at Cylinder head sub-assy | 21 | 214 | 15 |
| Ventilation case No. 1 at Cylinder block sub-assy | 9.0 | 92 | 80 in.lbf |
| Water inlet at Cylinder block sub-assy | 10 | 102 | 7 |
| Intake manifold at Cylinder head sub-assy | 34 | 347 | 25 |
| Intake manifold at Cylinder block sub-assy | 46 | 469 | 34 |
| Surge tank stay No. 1 at Intake manifold | 24 | 245 | 18 |
| Surge tank stay No. 1 at Cylinder head sub-assy | 24 | 245 | 18 |
| Exhaust manifold at Cylinder head sub-assy A | 50 | 510 | 37 |
| Exhaust manifold at Cylinder head sub-assy B | 21 | 214 | 16 |
| Exhaust manifold heat insulator No. 1 at Exhaust manifold | 20 | 204 | 15 |
| Manifold stay at Exhaust manifold | 50 | 510 | 37 |
| Manifold stay at Cylinder block sub-assy | 50 | 510 | 37 |
| V-ribbed belt tensioner assy at Timing chain or belt cover sub-assy Bolt | 100 | 1,020 | 74 |
| V-ribbed belt tensioner assy at Timing chain or belt cover sub-assy Nut | 29 | 296 | 21 |
| Flywheel sub-assy at Crankshaft 1st | 49 | 500 | 36 |
| Flywheel sub-assy at Crankshaft 2nd | Turn 90° | Turn 90° | Turn 90° |
| Transverse engine, engine mounting bracket rear at Transverse engine, engine mounting insulator rear | 65 | 663 | 48 |
| Transverse engine, engine mounting bracket front at Transverse engine, engine mounting insulator front | 52 | 530 | 38 |
| Transverse engine, engine mounting bracket LH at Transverse engine, engine mounting insulator LH | 80 | 816 | 59 |
| Transverse engine, engine mounting bracket RH at Transverse engine, engine mounting insulator RH | 52 | 530 | 38 |
| Front suspension crossmember sub-assy at Body Front | 113 | 1,152 | 83 |
| Front suspension crossmember sub-assy at Body Rear | 157 | 1,601 | 116 |
| Engine mounting member sub-assy center at Body | 39 | 398 | 29 |
| Vane pump oil reservoir bracket at Body | 7.8 | 80 | 69 in.lbf |
| Return tube sub-assy at Body Bolt A | 5.0 | 51 | 44 in.lbf |
| Return tube sub-assy at Body Bolt B | 7.8 | 80 | 69 in.lbf |
| Cruise control actuator at Cruise control bracket | 6.0 | 61 | 53 in.lbf |
| Air cleaner case at Body | 7.0 | 71 | 62 in.lbf |
| Air cleaner case at Transverse engine, engine mounting bracket LH | 7.0 | 71 | 62 in.lbf |
| Battery carrier at Body | 13 | 133 | 10 |
| Front wheel RH & LH at Front axle hub sub-assy RH & LH | 103 | 1,050 | 76 |
| Oil pan baffle plate at Crankshaft bearing cap sub-assy | 9.0 | 92 | 80 in.lbf |
| Oil strainer sub-assy at Crankshaft bearing cap sub-assy | 9.0 | 92 | 80 in.lbf |
| Oil pan sub-assy at Crankshaft bearing cap sub-assy | 9.0 | 92 | 80 in.lbf |
| Oil pan drain plug at Oil pan sub-assy | 37 | 377 | 27 |
| Oil filter union at Crankshaft bearing cap sub-assy | 30 | 306 | 22 |
| Cylinder head sub-assy at Cylinder block sub-assy 1st | 35 | 357 | 26 |
| Cylinder head sub-assy at Cylinder block sub-assy 2nd | Turn 180° | Turn 180° | Turn 180° |
| Valve rocker shaft sub-assy at Cylinder head sub-assy | 10 | 102 | 7 |
| Oil control valve filter at Cylinder head sub-assy | 29 | 296 | 21 |
| Camshaft timing oil control valve assy at Cylinder head sub-assy | 9.0 | 92 | 80 in.lbf |
| Cam timing control valve housing at Cylinder head sub-assy | 9.0 | 92 | 80 in.lbf |
| Camshaft timing gear assy at Camshaft | 54 | 551 | 40 |
| Camshaft timing gear or sprocket at No. 2 Camshaft | 54 | 551 | 40 |
| Camshaft bearing cap at Cylinder head sub-assy | 19 | 194 | 14 |
| Oil pump assy at Cylinder block sub-assy | 9.0 | 92 | 80 in.lbf |
| Chain vibration damper No. 1 at Cylinder head sub-assy | 21 | 214 | 15 |
| Chain vibration damper No. 1 at Cylinder block sub-assy | 21 | 214 | 15 |
| Chain tensioner slipper at Cylinder block sub-assy | 21 | 214 | 15 |
| Timing chain or belt cover sub-assy at Cylinder head sub-assy | 11 | 112 | 8 |
| Timing chain or belt cover sub-assy at Cylinder block sub-assy | 21 | 214 | 15 |
| Chain tensioner assy No. 1 at Timing chain or belt cover sub-assy | 9.0 | 92 | 80 in.lbf |
| Crankshaft pulley at Crankshaft | 120 | 1,224 | 89 |
| Transverse engine, engine mounting bracket at Timing chain or belt cover sub-assy | 49 | 500 | 36 |
| Water pump assy at Timing chain or belt cover sub-assy | 9.0 | 92 | 80 in.lbf |
| Water pump assy at Cylinder block sub-assy | 9.0 | 92 | 80 in.lbf |
| Water pump pulley at Water pump assy | 15 | 153 | 11 |
| Spark plug at Cylinder head sub-assy | 18 | 184 | 13 |
| Ventilation valve sub-assy at Cylinder head cover sub-assy | 27 | 275 | 20 |
| Stud bolt at Timing chain or belt cover sub-assy | 9.5 | 97 | 84 in.lbf |
| Stud bolt at Cylinder head sub-assy A, B, D and E | 9.5 | 97 | 84 in.lbf |
| Stud bolt at Cylinder head sub-assy C | 5.0 | 51 | 44 in.lbf |
| Stud bolt at Cylinder head sub-assy F | 19 | 194 | 14 |
| W/head taper screw plug No. 1 at Cylinder head sub-assy | 78 | 796 | 58 |
| Connecting rod cap at Connecting rod 1st | 30 | 306 | 22 |
| Connecting rod cap at Connecting rod 2nd | Turn 90° | Turn 90° | Turn 90° |
| Crankshaft bearing cap sub-assy at Cylinder block sub-assy 1st | 22 | 224 | 16 |
| Crankshaft bearing cap sub-assy at Cylinder block sub-assy 2nd | 44 | 449 | 32 |
| Crankshaft bearing cap sub-assy at Cylinder block sub-assy 3rd | Turn 180°45° | Turn 180°45° | Turn 180°45° |
| Crankshaft bearing cap sub-assy at Cylinder block sub-assy 4th | Turn 180°45° | Turn 180°45° | Turn 180°45° |
| Crankshaft bearing cap sub-assy at Cylinder block sub-assy Others | 18 | 184 | 13 |
| Stud bolt at Cylinder block sub-assy A, B and C | 5.0 | 51 | 44 in.lbf |
| Stud bolt at Cylinder block sub-assy D | 19 | 194 | 14 |
| Stud bolt at Cylinder block sub-assy E | 11 | 112 | 8 |
| Sub-assy oil nozzle No. 1 at Cylinder block sub-assy | 9.0 | 92 | 80 in.lbf |
| Screw plug at Crankshaft bearing cap sub-assy | 43 | 438 | 32 |
| Cylinder block water drain cock sub-assy at Cylinder block sub-assy | 25 | 255 | 18 |