Rear No. 1 Seat (RH): Disassembly

Using a screwdriver, remove the seatback board as shown.

HINT:

Tape the screwdriver tip before use.

1. Using a screwdriver, remove the cover.

   HINT:

   Tape the screwdriver tip before use.

2. Remove the screw and reclining adjuster release handle.
   Fig 1: Removing Seatback Board Using Screwdriver

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

1. Remove the 4 hog rings and open the seatback cover.

   HINT:

   At the time of reassembly, please refer to the following item. When installing hog rings, take care to prevent wrinkles as little as possible.

2. Remove the 2 corner pads.
3. Remove the 2 screws and 2 No. 1 reclining covers as shown.
   Fig 2: Locating No. 1 Reclining Cover Screws

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

1. Loosen the nuts, then remove the reclining connecting wire of RH side edge.
2. Remove the reclining connecting wire of LH side edge.
3. Remove the clamp and reclining connecting wire.
   Fig 3: Identifying Reclining Connecting Wire

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

Remove the 4 bolts and seatback assembly.

Torque: 37 N.m (380 kgf.cm, 27 ft.lbf) 

Fig 4: Identifying Seatback Assembly Bolts

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

1. Remove the 4 screws and reclining inner cover.
2. Remove the 2 hog rings.

   HINT:

   At the time of reassembly, please refer to the following item. When installing hog rings, take care to prevent wrinkles as little as possible.

3. Disengage the hook, then remove the headrest supports.
4. Remove the seatback frame.
5. Remove the 2 No. 1 protectors from the seatback frame.
   Fig 5: Removing Seatback Frame

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

Remove the hog rings and seatback cover.

HINT:

At the time of reassembly, please refer to the following item. When installing hog rings, take care to prevent wrinkles as little as possible.

Remove the 2 screws and 2 seat cushion under covers.

1. Using a screwdriver, disengage the hooks as shown.

   HINT:

   Fig 6: Disengaging Hooks

   Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

   Tape the screwdriver tip before use.

2. Remove the seat cushion cover with pad.

Remove the hog rings and seatback cover.

HINT:

At the time of reassembly, please refer to the following item. When installing hog rings, take care to prevent wrinkles as little as possible.

Remove the screw and cushion from the seat cushion under cover sub-assembly.

Remove the screw and lock cover.

Remove the screw and reclining remote control lever knob.

Remove the bolt and fold seat stopper band.

Remove the 2 screws and 2 seat cushion under covers.

Remove the 8 screws and rear seat cushion under cover.

Fig 7: Identifying Rear Seat Cushion Under Cover Screws

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

1. Remove the 2 bolts and rear No. 1 seat outer adjuster.

   Torque: 37 N.m (380 kgf.cm, 27 ft.lbf) 

2. Remove the 2 bolts and rear No. 1 seat inner adjuster.

   Torque: 37 N.m (380 kgf.cm, 27 ft.lbf) 

3. Remove the 2 hinge covers from the outer and inner adjusters.

Loosen the bolt, then remove the rear No. 1 seat inner belt.

Torque: 43 N.m (440 kgf.cm, 32 ft.lbf) 

Loosen the clamp and No. 2 fold seat lock control cable as shown.

Fig 8: Identifying No. 2 Fold Seat Lock Control Cable Componets

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

1. Using a screwdriver, remove the spring nut and E-ring.

   HINT:

   Tape the screwdriver tip before use.

2. Remove the No. 1 seat leg stay.

Fig 9: Locating No. 1 Seat Leg Stay Spring Nut & E-Ring

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

1. Using a screwdriver, remove the 2 E-rings.

   HINT:

   Tape the screwdriver tip before use.

2. Remove the 2 hinge pins, 2 cushion spacers, 2 cushion support springs and 2 rear seat cushion hinges.