Rear No. 1 Seat (RH): Disassembly

Using a screwdriver, remove the seatback board as shown in Fig 1 .

HINT:

Tape the screwdriver tip before use.

Fig 1: Removing Seat Back Board Using Screwdriver

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

1. Using a screwdriver, remove the cover.

   HINT:

   Tape the screwdriver tip before use.

2. Remove the screw and reclining adjuster release handle.

1. Remove the 4 hog rings and open the seatback cover.

   HINT:

   At the time of reassembly, please refer to the following item. When installing hog rings, take care to prevent wrinkles as little as possible.

2. Remove the 2 corner pads.
3. Remove the 2 screws and 2 No. 1 reclining covers as shown in Fig 2 .

Fig 2: Removing Seat Back Cover With 4 Hog Rings

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

1. Loosen the nuts, then remove the reclining connecting wire of RH side edge.
2. Remove the reclining connecting wire of LH side edge.
3. Remove the clamp and reclining connecting wire.

Fig 3: Removing Reclining Connecting Wire Of LH Side Edge

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

Remove the 4 bolts and seatback assembly.

1. Torque: 37 N.m (380 kgf.cm, 27 ft.lbf) 

Fig 4: Removing Seat Back Assembly Bolts

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

1. Remove the 4 screws and reclining inner cover.
2. Remove the 2 hog rings.

   HINT:

   At the time of reassembly, please refer to the following item. When installing hog rings, take care to prevent wrinkles as little as possible.

3. Disengage the hook, then remove the headrest supports.
4. Remove the seatback frame.
5. Remove the 2 No. 1 protectors from the seatback frame.

Remove the hog rings and seatback cover.

HINT:

At the time of reassembly, please refer to the following item. When installing hog rings, take care to prevent wrinkles as little as possible.

Remove the 2 screws and 2 seat cushion under covers.

Fig 5: Removing Seat Back Frame

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

1. Using a screwdriver, disengage the hooks as shown in Fig 6 .

   HINT:

   Tape the screwdriver tip before use.

2. Remove the seat cushion cover with pad.

Remove the hog rings and seatback cover.

HINT:

At the time of reassembly, please refer to the following item. When installing hog rings, take care to prevent wrinkles as little as possible.

Remove the screw and cushion from the seat cushion under cover sub-assembly.

Remove the screw and lock cover.

Remove the screw and reclining remote control lever knob.

Remove the bolt and fold seat stopper band.

Remove the 2 screws and 2 seat cushion under covers.

Fig 6: Removing Seat Cushion Cover With Pad Using Screw Driver

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

Remove the 8 screws and rear seat cushion under cover.

1. Remove the 2 bolts and rear No. 1 seat outer adjuster.
   1. Torque: 37 N.m (380 kgf.cm, 27 ft.lbf) 
2. Remove the 2 bolts and rear No. 1 seat inner adjuster.
   1. Torque: 37 N.m (380 kgf.cm, 27 ft.lbf) 
3. Remove the 2 hinge covers from the outer and inner adjusters.

Loosen the bolt, then remove the rear No. 1 seat inner belt.

1. Torque: 43 N.m (440 kgf.cm, 32 ft.lbf) 

Fig 7: Removing Rear Seat Cushion Under Cover Sub Assembly

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

Loosen the clamp and No. 2 fold seat lock control cable as shown in Fig 8 .

Fig 8: Removing No. 2 Fold Seat Lock Cable

Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002

1. Using a screwdriver, remove the spring nut and E-ring.

   HINT:

   Tape the screwdriver tip before use.

2. Remove the No. 1 seat leg stay.

1. Using a screwdriver, remove the 2 E-rings.

   HINT:

   Tape the screwdriver tip before use.

2. Remove the 2 hinge pins, 2 cushion spacers, 2 cushion support springs and 2 rear seat cushion hinges.