Data List/Active Test

1. While the hand-held tester is connected to the DLC3 with the ignition switch is turned to the ON position, the ABS, TRAC and VSC data list can be displayed. Follow the prompts on the tester screen to access the "DATA LIST".
   DATA LIST
   
   

   Item	Measurement Item/Range (Display)	Normal Condition	Diagnostic Note
   HB MOT RELAY	HB motor relay/ON or OFF	ON: During pump motor operation OFF: No pump motor operation	-
   SOL RELAY	Solenoid relay/ON or OFF	ON: Solenoid relay ON OFF: Solenoid relay OFF	-
   AIR BLD SUPPORT	Air bleed availability/SUPPORT or NOT SUP	SUPPORT: Support ON NOT SUP: Support OFF	-
   IDLE SW	Main idle switch/ON or OFF	ON: Accelerator pedal released OFF: Accelerator pedal depressed	-
   STOP LIGHT SW	Stop light switch/ON or OFF	ON: Brake pedal depressed OFF: Brake pedal released	-
   PKBSW	Parking brake switch/ON or OFF	ON: Parking brake applied OFF: Parking brake released	-
   ABS OPERT FR	ABS operation (FR)/BEFORE or OPERATE	BEFORE: No ABS operation (FR) OPERATE: During ABS operation (FR)	-
   ABS OPERT FL	ABS operation (FL)/BEFORE or OPERATE	BEFORE: No ABS operation (FL) OPERATE: During ABS operation (FL)	-
   ABS OPERT RR	ABS operation (RR)/BEFORE or OPERATE	BEFORE: No ABS operation (RR) OPERATE: During ABS operation (RR)	-
   ABS OPERT RL	ABS operation (RL)/BEFORE or OPERATE	BEFORE: No ABS operation (RL) OPERATE: During ABS operation (RL)	-
   WHEEL SPDFR	Wheel speed sensor (FR) reading/mm 0 mph (0 km/h), max 202 mph (326 km/h)	Actual wheel speed	Similar speed as indicated on speedometer
   WHEEL SPD FL	Wheel speed sensor (FL) reading/ mm 0 mph (0 km/h), max 202 mph (326 km/h)	Actual wheel speed	Similar speed as indicated on speedometer
   WHEEL SPDRR	Wheel speed sensor (RR) reading/mm 0 mph (0 km/h) max 202 mph (326 km/h)	Actual wheel speed	Similar speed as indicated on speedometer
   WHEELSPD RL	Wheel speed sensor (RL) reading/mm 0 mph (0 km/h) max 202 mph (326 km/h)	Actual wheel speed	Similar speed as indicated on speedometer
   DECELERAT SEN	Deceleration sensor 1 reading/ mm -1 869 G, max 1 869 G	Approximately 0 +/- 0 13 G while stationary	Reading changes when vehicle is bounced
   DECELERAT SEN2	Deceleration sensor 2 reading/ mm -1 869 G, max 1 869 G	Approximately 0 +/- 0 13 G while stationary	Reading changes when vehicle is bounced
   IG VOLTAGE	ECU IG power supply voltage/ TOO LOW/NORMAL/TOO HIGH	TOO LOW: 9 5 V or less NORMAL: 9 5 or 14 0 V TOO HIGH: 14 0 V or more	-
   SFRR	ABS solenoid (SFRR)/ON or OFF	ON: Operates	-
   SFRH	ABS solenoid (SFRH)/ON or OFF	ON: Operates	-
   SFLR	ABS solenoid (SFLR)/ON or OFF	ON: Operates	-
   SFLH	ABS solenoid (SFLH)/ON or OFF	ON: Operates	-
   SRRR (SRR)	ABS solenoid (SRRR (SRR))/ON or OFF	ON: Operates	-
   SRRH (SRH)	ABS solenoid (SRRH (SRH))/ON or OFF	ON: Operates	-
   SRLR	ABS solenoid (SRLR)/ON or OFF	ON: Operates	-
   SRLH	ABS solenoid (SRLH)/ON or OFF	ON: Operates	-
   SRCF(SA1)	TRAC solenoid (SMCF)/ ON or OFF	-	-
   SRCR (SA2)	TRAC solenoid (SREA)/ ON or OFF	-	-
   SRMF (SMCF, SA3)	TRAC solenoid (SREC)/ ON or OFF	-	-
   SRMR (SMCR, STR)	TRAC solenoid (STR)/ON or OFF	-	-
   ENGINE SPD	Engine speed/ min 0 rpm, max 6000 rpm	Actual engine speed	-
   VEHICLE SPD	Vehicle speed reading/ Min 0 mph (0 km/h), max 202 mph (326 km/h)	Actual vehicle speed	Speed indicated on speedometer
   YAW RATE	Yaw rate sensor/ min -128 deg/s, max 127 deg/s	Min.: -128 deg/s Max.: 128 deg/s	-
   YAW ZERO VALUE	Memorized zero value/ min -128deg/s, max 127deg/s	Min.: -128 deg/s Max.: 128 deg/s	-
   STEERING ANG	Steering angle sensor/ min -1152 deg/s, max 1150 875 deg/s	Left turn: Increase Right turn: Decrease	-
   MAS CYL PRESS 1	Master cylinder pressure sensor 1 reading/ Min 0 V, max 5 V	When brake pedal is released 0 3 to 0 9V When stop light is turned on 0 3 to 09 V	Reading increases when brake pedal is depressed
   TEST MODE	Test mode operation/NORMAL or TEST	NORMAL: Normal mode TEST: During test mode	-
   #CODES	Number of DTC recorded/ min 0, max 255	-	-
   ECU CODE #4	ECU code	1 or 0	0
   ECU CODE #3	ECU code	1 or 0	0
   ECU CODE #2	ECU code	1 or 0	0
   ECU CODE #1	ECU code	1 or 0	0
   WHEEL DIR FR	Wheel direction (FR)/ FORWARD or BACK	FORWARD: Forward BACK: Back	-
   WHEEL DIR FL	Wheel direction (FL)/ FORWARD or BACK	FORWARD: Forward BACK: Back	-
   WHEEL DIR RR	Wheel direction (RR)/ FORWARD or BACK	FORWARD: Forward BACK: Back	-
   WHEEL DIR RL	Wheel direction (RL)/ FORWARD or BACK	FORWARD: Forward BACK: Back	-
   RESERVOIR SW	Brake fluid level warning switch/ ON or OFF	ON: Switch ON OFF: Switch OFF	-
   ACC PRESS	Accumulator pressure sensor/ min 0 V, max 5 V	3.58 to 5 V	If the value is constant regardless of pump operation, accumulator pressure sensor malfunction is suspected
   SPD SEN FR	Speed sensor open detection (FR)/OPN DET or NORMAL	OPN DET: Momentary interruption NORMAL: Normal	-
   SPD SEN FL	Speed sensor open detection (FL)/OPN DET or NORMAL	OPN DET: Momentary interruption NORMAL: Normal	-
   SPD SEN RR	Speed sensor open detection (RR)/OPN DET or NORMAL	OPN DET: Momentary interruption	-
   SPD SEN RL	Speed sensor open detection (RL)/OPN DET or NORMAL	OPN DET: Momentary interruption NORMAL: Normal	-
   ACCELERATOR %	The difference of a present accel-erator/min 0%, max 128%	-	-
   TORQUE	Real output torque/ min -1024 Nm, max 1016 Nm	-	-

HINT:

Performing the ACTIVE TEST using the hand-held tester allows the relay, actuator, etc. to operate without removing any parts. Performing the ACTIVE TEST as the first step of troubleshooting is one of the methods to shorten labor time.

It is possible to display the DATA LIST during the ACTIVE TEST.

1. Connect the hand-held tester to the DLC3.
2. Turn the ignition switch to the ON position.
3. According to the display on the tester, perform the "ACTIVE TEST".

HINT:

The ignition switch must be turned to the ON position to proceed to the ACTIVE TEST using the hand-held tester.