LEMON Manuals: Even more car manuals for everyone
Home >> Toyota >> 2001 >> Sienna CE >> Repair and Diagnosis >> External Pages >> Different car >> Section 73 (Air Bag Restraint Systems) >> Diagnostic Tests >> DTC 32/B1140: Right-Side Air Bag Sensor Assembly Malfunction >> Diagnostic Procedure

Diagnostic Procedure

WARNING: This page is about a different car, the 2002 Toyota Celica. However, it is still accessible from the selected car via links, so may be relevant.
  1. Turn ignition switch to ON position. Wait at least 20 seconds. Clear DTCs. See CLEARING CODES  under DIAGNOSTICS. Turn ignition switch to LOCK position. Wait at least 20 seconds. Turn ignition switch to ON position. Wait at least 20 seconds. Retrieve DTCs. See RETRIEVING CODES  under DIAGNOSTICS. If DTC 32/B1140 is displayed, go to next step. If DTC 32/B1140 is not displayed, system is functioning properly at this time. Check for intermittent fault. See AIR BAG WARNING LIGHT INTERMITTENT .
  2. Access right-side air bag sensor assembly. See SIDE AIR BAG SENSOR  under REMOVAL & INSTALLATION. Ensure right-side air bag sensor assembly harness connector is properly connected and secure. Repair connector as necessary. Go to next step.
  3. Disable air bag system. See DISABLING SYSTEM  under DISABLING & ACTIVATING AIR BAG SYSTEM.
  4. Disconnect right-side air bag sensor assembly connector. Connect jumper wire between right-side air bag sensor assembly harness connector terminals No. 2 (circuit SSR+, Blue/Yellow wire) and No. 4 (circuit ESR, Gray wire). See Fig 1. Measure resistance between air bag sensor assembly connector C8, terminals No. 10 (circuit SSR+, Blue/Yellow wire) and No. 7 (circuit ESR, Gray wire). See Figure. If resistance is less than one ohm, go to next step. If resistance is more than one ohm, repair or replace harness or connector between right-side air bag sensor assembly and air bag sensor assembly.
  5. Connect jumper wire between right-side air bag sensor assembly harness connector terminals No. 1 (circuit VUPR, Pink wire) and No. 3 (circuit FSR, Light Green wire). See Fig 1. Measure resistance between air bag sensor assembly connector C8, terminals No. 12 (circuit VUPR, Pink wire) and No. 9 (circuit FSR, Light Green wire). See Figure. If resistance is less than one ohm, go to next step. If resistance is more than one ohm, repair or replace harness or connector between right-side air bag sensor assembly and air bag sensor assembly.
  6. Measure resistance between ground and air bag sensor assembly harness connector C8, terminals No. 12 (circuit VUPR, Pink wire), No. 10 (circuit SSR+, Blue/Yellow wire) and No. 9 (circuit FSR, Light Green wire) individually. See Figure. If resistance in all tests is less than one ohm, go to next step. If resistance in any test is more than one ohm, repair or replace harness or connector between right-side air bag sensor assembly and air bag sensor assembly. See WIRING DIAGRAMS .
  7. Connect negative battery cable. Turn ignition switch to ON position. Measure voltage between ground and air bag sensor assembly harness connector C8, terminals No. 12 (circuit VUPR, Pink wire), No. 10 (circuit SSR+, Blue/Yellow wire), No. 9 (circuit FSR, Light Green wire) and No. 7 (circuit ERS, Gray wire) individually. See Figure. If zero volt is present in all tests, turn ignition switch to LOCK position, disconnect negative battery cable and go to next step. If more than zero volt is present in any test, repair or replace harness or connector between right-side air bag sensor assembly and air bag sensor assembly. See WIRING DIAGRAMS .
  8. Ensure negative battery cable is disconnected. Reconnect side air bag sensor connector and air bag sensor assembly connector C8. Connect negative battery cable. Wait at least 2 seconds. Turn ignition switch to ON position. Wait at least 20 seconds. Clear DTCs. See CLEARING CODES  under DIAGNOSTICS. Turn ignition switch to LOCK position. Wait at least 20 seconds. Turn ignition switch to ON position. Wait at least 20 seconds. Retrieve DTCs. See RETRIEVING CODES  under DIAGNOSTICS. If DTC 32/B1140 is not displayed, system is functioning properly at this time. Check for intermittent fault. See AIR BAG WARNING LIGHT INTERMITTENT . If DTC 32/B11402 is displayed, go to next step.
  9. Turn ignition switch to LOCK position. Disconnect negative battery cable. Wait at least 90 seconds. Disconnect right-side air bag sensor assembly. Disconnect left-side air bag sensor assembly. Connect left-side air bag sensor assembly to right-side air bag sensor assembly harness connector. Connect negative battery cable. Wait at least 2 seconds. Turn ignition switch to ON position. Wait at least 20 seconds. Clear DTCs. See CLEARING CODES  under DIAGNOSTICS. Turn ignition switch to LOCK position. Wait at least 20 seconds. Turn ignition switch to ON position. Wait at least 20 seconds. Retrieve DTCs. See RETRIEVING CODES  under DIAGNOSTICS. If DTC 32/B1140 is not displayed, go to next step. If DTC 32/B1140 is displayed, replace air bag sensor assembly.
  10. Turn ignition switch to LOCK position. Disconnect negative battery cable. Wait at least 90 seconds. Connect right-side air bag sensor assembly to left-side air bag sensor assembly harness connector. Connect negative battery cable. Wait at least 2 seconds. Turn ignition switch to ON position. Wait at least 20 seconds. Clear DTCs. See CLEARING CODES  under DIAGNOSTICS. Turn ignition switch to LOCK position. Wait at least 20 seconds. Turn ignition switch to ON position. Wait at least 20 seconds. Retrieve DTCs. See RETRIEVING CODES  under DIAGNOSTICS. If DTC 33/B1141 is not displayed, system is functioning properly at this time. Check for intermittent fault. See AIR BAG WARNING LIGHT INTERMITTENT . If DTC 33/B1141 is displayed, replace right-side air bag sensor assembly.
Fig 1: Identifying Side Air Bag Sensor Assembly Harness Connector
G99C20505Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
scientia non olet · About LEMON Manuals