LEMON Manuals: Even more car manuals for everyone
Home >> Toyota >> 2001 >> Sienna CE >> Repair and Diagnosis >> External Pages >> Different car >> Section 73 (Air Bag Restraint Systems) >> Diagnostic Tests >> DTC 15/B1156 & B1157: Right Front Air Bag Sensor Malfunction >> Diagnostic Procedure

Diagnostic Procedure

WARNING: This page is about a different car, the 2002 Toyota Celica. However, it is still accessible from the selected car via links, so may be relevant.
  1. Disable air bag system. See DISABLING SYSTEM  under DISABLING & ACTIVATING AIR BAG SYSTEM. Reconnect negative battery cable. Ensure right front air bag sensor harness connector is disconnected.
  2. Turn ignition switch to ON position. Measure voltage between ground and air bag sensor assembly connector C6, terminal No. 9 (Black/White wire, circuit SR+). See Figure. Measure voltage between ground and air bag sensor assembly connector C6, terminal No. 20 (Brown/White wire, circuit SR-). If voltage in both tests is less than one volt, turn ignition switch to LOCK position. Go to next step. If any voltage is more than one volt, go to step  8.
  3. Measure resistance between ground and air bag sensor assembly connector C6, terminal No. 9 (Black/White wire, circuit SR+). See Figure. Measure resistance between ground and air bag sensor assembly connector C6, terminal No. 20 (Brown/White wire, circuit SR-). If resistance in both tests is more than one megohm, go to next step. If any resistance is less than one megohm, go to step  9.
  4. Measure resistance between air bag sensor assembly connector C6, terminals No. 9 (Black/White wire, circuit SR+) and terminal No. 20 (Brown/White wire, circuit SR-). If resistance is more than one megohm, go to next step. If resistance is less than one megohm, go to step  10.
  5. Connect jumper wire between Black/White and Brown/White wires on air bag sensor assembly side of front air bag sensor harness connector. Measure resistance between air bag sensor assembly connector C6, terminals No. 9 (Black/White wire, circuit SR+) and terminal No. 20 (Brown/White wire, circuit SR-). If resistance is less than one ohm, go to next step. If resistance is more than one ohm, go to step  11.
  6. Measure resistance between front air bag sensor connector terminals. If resistance is 300-1500 ohms, go to next step. If resistance is not 300-1500 ohms, replace front air bag sensor.
  7. Turn ignition switch to LOCK position. Disconnect negative battery cable. Wait at least 90 seconds. Connect air bag sensor assembly connector. Connect right front air bag sensor. Connect negative battery cable. Wait at least 20 seconds. Turn ignition switch to ON position. Clear DTCs. See CLEARING CODES  under DIAGNOSTICS. Turn ignition switch to LOCK position. Wait at least 20 seconds. Turn ignition switch to ON position. Wait at least 20 seconds. Retrieve codes. See RETRIEVING CODES  under DIAGNOSTICS. If DTC 15/B1156 or B1157 is displayed, replace right front air bag sensor. If DTC 15/B1156 or B1157 is not displayed, system is functioning properly at this time. Check for intermittent fault. See AIR BAG WARNING LIGHT INTERMITTENT  under DIAGNOSTIC TESTS.
  8. Disconnect right front air bag sensor Yellow 2-pin sub-harness connector located behind right kick panel. Measure voltage between ground and Black/White wire on front air bag sensor side of sub-harness connector. Measure voltage between ground and Brown/White wire on front air bag sensor side of sub-harness connector. If voltage is less than one volt, repair or replace wire harness or connector between air bag sensor assembly and sub-harness connector. If voltage is more than one volt, repair or replace wire harness between sub-harness connector and front air bag sensor.
  9. Disconnect right front air bag sensor Yellow 2-pin sub-harness connector located behind right kick panel. Measure resistance between ground and Black/White wire on front air bag sensor side of sub-harness connector. Measure resistance between ground and Brown/White wire on front air bag sensor side of sub-harness connector. If resistance is more than one megohm, repair or replace wire harness or connector between air bag sensor assembly and sub-harness connector. If resistance is less than one megohm, repair or replace wire harness between sub-harness connector and front air bag sensor.
  10. Disconnect right front air bag sensor Yellow 2-pin sub-harness connector located behind right kick panel. Measure resistance between Black/White and Brown/White wires on front air bag sensor side of sub-harness connector. If resistance is more than one megohm, repair or replace wire harness or connector between air bag sensor assembly and sub-harness connector. If resistance is less than one megohm, repair or replace wire harness between sub-harness connector and front air bag sensor.
  11. Disconnect right front air bag sensor Yellow 2-pin sub-harness connector located behind right kick panel. Connect jumper wire between Black/White and Brown/White wires on air bag sensor assembly side of front air bag sensor harness connector. Measure resistance between Black/White and Brown/White wires on front air bag sensor side of sub-harness connector. If resistance is less than one ohm, repair or replace wire harness or connector between air bag sensor assembly and sub-harness connector. If resistance is more than one ohm, repair or replace wire harness between sub-harness connector and front air bag sensor.
scientia non olet · About LEMON Manuals