LEMON Manuals: Even more car manuals for everyone
Home >> Toyota >> 2001 >> Sienna CE >> Repair and Diagnosis >> External Pages >> Different car >> Section 451 (Power Tilt & Telescopic Steering Column - Diagnosis) >> Problem Symptoms Table

Problem Symptoms Table

WARNING: This page is about a different car, the 2003 Lexus LS 430. However, it is still accessible from the selected car via links, so may be relevant.

This system uses the multiplex communication system, so check diagnosis system of the multiplex communication system before you proceed with troubleshooting.

The table below will be useful for you in troubleshooting these electrical systems. The most likely causes of the malfunction are shown in the order of their probability. Inspect each part in the order shown, and replace the part when it is found to be faulty.

If the instruction "Proceed to next circuit inspection shown on the chart" is given in the flow chart for each circuit, proceed to the circuit with the next highest number in the table to continue the check.

If the problem still occurs even though there are no abnormalities in any of the other circuits, then check and replace ECU.

PROBLEM SYMPTOMS REFERENCE

Symptom Suspect Area See Section
Both tilt and telescopic:
Manual, auto away/return and memory functions
  • Do not operate
  • Stop part way
  • Do not stop
  1. ECU power source circuit
  2. Key unlock warning switch
  3. Actuator power source circuit
  4. Sensor power source circuit
  5. Tilt motor circuit
  6. Telescopic motor circuit
  7. Power tilt and power telescopic ECU
  1. ECU POWER SOURCE CIRCUIT 
  2. INSPECTION
  3. ACTUATOR POWER SOURCE CIRCUIT 
  4. SENSOR POWER SOURCE CIRCUIT 
  5. TILT MOTOR CIRCUIT 
  6. TELESCOPIC MOTOR CIRCUIT 
  7. HOW TO USE THE DIAGNOSTIC CHART AND INSPECTION PROCEDURE
Tilt only:
Manual, auto away/return and memory functions
  • Do not operate
  • Stop part way
  • Do not stop
  1. Sensor power source circuit
  2. Tilt motor circuit
  3. Power tilt and power telescopic ECU
  1. SENSOR POWER SOURCE CIRCUIT 
  2. TILT MOTOR CIRCUIT 
  3. HOW TO USE THE DIAGNOSTIC CHART AND INSPECTION PROCEDURE
Telescopic only:
Manual, auto away/return and memory functions
  • Do not operate
  • Stop part way
  • Do not stop
  1. Sensor power source circuit
  2. Telescopic motor circuit
  3. Power tilt and power telescopic ECU
  1. SENSOR POWER SOURCE CIRCUIT 
  2. TELESCOPIC MOTOR CIRCUIT 
  3. HOW TO USE THE DIAGNOSTIC CHART AND INSPECTION PROCEDURE
Both tilt and telescopic:
Only tilt and telescopic manual switch function does not operate
  1. Tilt and telescopic manual switch circuit
  2. Power tilt and power telescopic ECU
  1. TILT AND TELESCOPIC MANUAL SWITCH CIRCUIT
  2. HOW TO USE THE DIAGNOSTIC CHART AND INSPECTION PROCEDURE
Tilt only:
Only tilt and telescopic manual switch function does not operate
  1. Tilt and telescopic manual switch circuit
  2. Power tilt and power telescopic ECU
  1. TILT AND TELESCOPIC MANUAL SWITCH CIRCUIT
  2. HOW TO USE THE DIAGNOSTIC CHART AND INSPECTION PROCEDURE
Telescopic only:
Only tilt and telescopic manual switch function does not operate
  1. Tilt and telescopic manual switch circuit
  2. Power tilt and power telescopic ECU
  1. TILT AND TELESCOPIC MANUAL SWITCH CIRCUIT
  2. HOW TO USE THE DIAGNOSTIC CHART AND INSPECTION PROCEDURE
Both away and return:
Only auto away/return function does not operate
  1. Check status of auto away function using LEXUS handheld tester
  2. Ignition switch
  3. Key unlock warning switch
  4. Power tilt and power telescopic ECU
  1. -
  2. INSPECTION
  3. INSPECTION
  4. HOW TO USE THE DIAGNOSTIC CHART AND INSPECTION PROCEDURE
Only away:
Only auto away/return function does not operate
  1. Key unlock warning switch
  2. Ignition switch
  3. Power tilt and power telescopic ECU
  1. INSPECTION
  2. INSPECTION
  3. HOW TO USE THE DIAGNOSTIC CHART AND INSPECTION PROCEDURE
Only return:
Only auto away/return function does not operate
  1. Key unlock warning switch
  2. Ignition switch
  3. Power tilt and power telescopic ECU
  1. INSPECTION
  2. INSPECTION
  3. HOW TO USE THE DIAGNOSTIC CHART AND INSPECTION PROCEDURE