Glass - Rear Quarter - LH - Remove And Install: Install

Apply primer to the urethane path and any areas where the paint was damaged during the removal of the LH rear quarter glass. Allow the primer to dry for at least 2 minute.

Courtesy of TESLA, INC.
Remove the body patches (x2) from the quarter panel.

Courtesy of TESLA, INC.
Prepare the caulking gun and urethane.
NOTE: The urethane opening must be 7 mm wide and 12 mm tall.
Apply urethane to the LH rear quarter glass, following the original path.
NOTE: If quarter glass is being reused, apply urethane surrounding the datum location. This will eliminate potential wind noise.
Position the LH rear quarter glass onto the vehicle.
NOTE: Start by positioning the datum into place. Verify the threads for bolt installation are aligned with the body. Apply pressure to the surrounding areas. Use tape to hold glass in place. Reference urethane being applied to confirm dry time.

Courtesy of TESLA, INC.
Install the bolts (x2) that attach the LH rear quarter glass to the body.
Torque 10 N.m

Tip: Use of the following tool(s) is recommended:
- 10 mm socket
Courtesy of TESLA, INC.

Courtesy of TESLA, INC.
Install the clips (x5) that attach the rear of the headliner to the vehicle.
NOTE: Verify the clips are properly seated prior to installation. Replace any damaged or missing clips as needed.

Courtesy of TESLA, INC.

Courtesy of TESLA, INC.
Install the bolts (x2) that attach the rear of the headliner to the body.
Torque 3 N.m

NOTE: The bolts are located on the LH and RH sides of the headliner.

Tip: Use of the following tool(s) is recommended:
- Torx T30 socket
Courtesy of TESLA, INC.

Courtesy of TESLA, INC.
Install the screw that attaches the RH rear coat hook to the headliner.
Torque 2.5 N.m

Tip: Use of the following tool(s) is recommended:
- Torx T25 socket
Courtesy of TESLA, INC.
Install the RH rear coat hook screw cover.

Courtesy of TESLA, INC.
Push to close the RH rear coat hook.

Courtesy of TESLA, INC.
Move the RH upper C-pillar trim into position, and then install the clips (x7) that attach the trim to the vehicle.
NOTE: Replace any damaged clips as needed.

Courtesy of TESLA, INC.

Courtesy of TESLA, INC.

Courtesy of TESLA, INC.
Position the RH mid C-pillar trim into the vehicle, and then install the clips (x3) that attach the trim to the vehicle.
NOTE: Replace any damaged clips as needed.

Courtesy of TESLA, INC.

Courtesy of TESLA, INC.

Courtesy of TESLA, INC.
Install the clips (x4) that attach the RH lower C-pillar trim to the RH mid C-pillar trim.

Courtesy of TESLA, INC.
Fold the RH 2nd row seat to the vertical position.
NOTE: Remove the seat cushion protection if present.
Install the RH 2nd row seat outer side bolster. See Bolster - Outer - Seat - 2nd Row - LH (Remove and Replace) .
Install the RH upper B-pillar trim. See Trim - B- Pillar - Upper - LH (Remove and Replace) .
Move front passenger seat to its original position.
Repeat step 9 through step 17 for the LH side of the vehicle.
Install the LH rocker panel seal to the quarter panel area.
NOTE: Apply promoter to the double sided tape. If damage is present on double sided tape, replace with new piece.

Courtesy of TESLA, INC.
Remove the masking tape from the LH rear quarter glass.
Install the LH body side brightwork. See Brightwork - Body Side - LH (Remove and Replace) .
Install the rear trunk parcel shelf. See Parcel Shelf - Rear Trunk (Remove and Replace) .
Close the liftgate.
Raise all the windows and close all the doors.