LEMON Manuals: Even more car manuals for everyone
Home >> Tesla >> 2024 >> Model 3 Long Range >> Repair and Diagnosis (Single Page) >> Body & Frame >> Exterior/Interior Trim >> Body -- Model 3 >> Windshield and Body Glass >> Front And Rear Door Glass - Glass, Front Door LH - Remove And Replace >> Install

Front And Rear Door Glass - Glass, Front Door LH - Remove And Replace: Install

  1. Install the LH front door glass.
  2. Inspect the regulator isolator clamps for glass splinters or other debris, and clean them if necessary.
    CAUTION: Debris and splinters may damage or shatter the new door glass.
  3. Position the front LH door glass onto the front LH door, and then hand tighten the bolts (x2) that secure the glass to the regulator isolation clamps.
    NOTE: Make sure the clamps are not bottomed out on the regulator.
    G16587763Courtesy of TESLA, INC.
  4. Align the center of the glass with the guide block opening.
  5. Install the LH front door outer belt seal. See FRONT DOOR SEALS - FRONT DOOR OUTER BELT ASSEMBLY LH - BLACK - REMOVE AND REPLACE .
  6. Lower the front LH window fully and close the LH front door.
  7. Raise the LH front window fully by accessing the window switch tool through the LH rear door.
  8. Use the gap and flush tool to inspect the front LH window for proper gap and flush.
    • Gap: 8 mm +/- 1.7 mm
    • Flush: 0 mm +/- 1.7 mm
  9. Open the LH front door.
  10. If the glass gap and flush is out of specifications: Loosen the bolts that attach the glass to the regulator isolator clamps approximately 1/2 turn to maintain position of the glass but still allow adjustment of the glass, and then adjust the glass to gap and flush specifications.
  11. Once the glass gap and flush is in specifications, hand tighten the patched bolts (x2) that attach the glass to the regulator isolator clamps.
    G16587764Courtesy of TESLA, INC.
  12. Raise the LH front window fully by accessing the window switch tool through the LH rear door.
  13. Close the LH front door.
  14. Check again the gap and flush of the front LH door glass and make adjustments, if necessary.
  15. Open the LH front door.
  16. Torque the patched bolts (x2) that secure the glass to the regulator isolator clamps

    9.5 N.m (7.0 lbs-ft)  .

    Tip: Use of the following tool(s) is recommended:

    • 13 mm socket
    • 2 in extension
    • Cordless Ratchet/Impact Driver
    • Ratchet/torque wrench (for installation only)
    G16587765Courtesy of TESLA, INC.
  17. Lower the front LH window.
  18. Disconnect the window switch special tool.
  19. Install the plugs that cover the openings in the door regulator isolation clamps.
    G16587766Courtesy of TESLA, INC.
  20. Install the LH front door trim panel. See INTERIOR TRIM - DOOR TRIM - FRONT DOOR TRIM PAD - DOOR TRIM ASSEMBLY - LH - REMOVE AND REPLACE .
  21. Install the LH front door puddle light. See INTERIOR TRIM - DOOR TRIM - FRONT DOOR TRIM PAD - PUDDLE LAMP - REMOVE AND REPLACE .
  22. Install the LH front door tweeter. See FRONT DOOR TRIM PAD - DOOR TRIM, TWEETER ASSEMBLY, FRONT LH - REMOVE AND REPLACE .
  23. Install the LH front door reflector. See INTERIOR TRIM - DOOR TRIM - FRONT DOOR TRIM PAD - DOOR REFLECTOR - REMOVE AND REPLACE .
  24. Unlock the vehicle gateway. See GATEWAY UNLOCK .
  25. On the touchscreen, touch Controls > Service Mode > Windows > Calibrate Windows  , then select Start  to calibrate the window.
  26. Disable Service Mode. See SERVICE MODE .
scientia non olet · About LEMON Manuals