LEMON Manuals: Even more car manuals for everyone
Home >> Tesla >> 2024 >> Model 3 Long Range >> Repair and Diagnosis (Single Page) >> Accessories & Equipment >> Seats -- Model 3 >> Front Seat Tracks and Motors >> Front Seat Sliders And Controllers - Driver Seat Cushion Suspension - Remove And Replace >> Install

Front Seat Sliders And Controllers - Driver Seat Cushion Suspension - Remove And Replace: Install

  1. With assistance, install the lower part of the LH front seat cushion suspension to the seat frame.
    NOTE: Clip the seat suspension to the seat frame in a horizontal position and then rotate upwards.
    G16588788Courtesy of TESLA, INC.
    G16588789Courtesy of TESLA, INC.
    G16588790Courtesy of TESLA, INC.
  2. With assistance, install the upper part of the LH front seat cushion suspension to the seat frame.
    NOTE: Reversely use the clip prytool to install the seat suspension. Press the seat suspension down with appropriate force to install it to the inside of the seat frame.
    G16588791Courtesy of TESLA, INC.
    G16588792Courtesy of TESLA, INC.
    G16588793Courtesy of TESLA, INC.
  3. Install the seat cushion retaining clips (x2) to the LH front seat suspension.
    NOTE: Pull the clips tight till the seat suspension is at a proper position for installation.
    G16588794Courtesy of TESLA, INC.
  4. Install the clip which is next to the cushion heater connector and attaches the harness to the bottom of the LH front seat.
    G16588795Courtesy of TESLA, INC.
  5. Fasten the clip that attaches the seat cushion heater connector to the seat underside, and then connect the connector.
    NOTE: Slide the connector onto the seat frame clip to secure.
    G16588796Courtesy of TESLA, INC.
    G16588797Courtesy of TESLA, INC.
    G16588798Courtesy of TESLA, INC.
  6. Install the retaining clip that attaches the seat occupancy sensor to the seat underside.
    G16588799Courtesy of TESLA, INC.
  7. Fasten the clip that attaches the seatback heater connector to the seat underside, and then connect the connector.
    NOTE: Slide the connector onto the seat frame clip to secure.
    G16588800Courtesy of TESLA, INC.
    G16588801Courtesy of TESLA, INC.
    G16588802Courtesy of TESLA, INC.
  8. Secure the clips (x3) to install the seat harness bracket to the LH front seat assembly.
    G16588803Courtesy of TESLA, INC.
  9. Connect the seat occupancy sensor connector, then secure the tabs (x2) to install the connector to the LH front seat harness bracket.
    G16588804Courtesy of TESLA, INC.
    G16588805Courtesy of TESLA, INC.
    G16588806Courtesy of TESLA, INC.
  10. Install the straps (x2) to the LH front seat harness bracket.
    G16588807Courtesy of TESLA, INC.
  11. Connect the LV battery power. See LV BATTERY - LI-ION - DISCONNECT AND CONNECT .
  12. Move the LH front seat to most rearward.
  13. Install the clip that attaches the LH front seat harness to the outboard seat track.
    G16588808Courtesy of TESLA, INC.
  14. Return the LH front seat to the vertical position.
    NOTE: Take care when moving the seat. Ensure the carpet is not damaged.
  15. Secure the LH front seat harness to the sill trim clips (x5).
    NOTE: Tuck excess harness between the harness bracket and the body.
    G16588809Courtesy of TESLA, INC.
    G16588810Courtesy of TESLA, INC.
  16. Install new LH front seat front fasteners (x2) (1458818-00-B).

    33.5 N.m (24.7 lbs-ft) 

    Tip: Use of the following tool(s) is recommended:

    • Cordless Ratchet/Impact Driver
    • Torx T45 socket
    • Torx Plus T45 socket
    • Flex head ratchet/flex head torque wrench (for installation only)
    G16588811Courtesy of TESLA, INC.
  17. Move the LH front seat forward, and then install new LH front seat rear fasteners (x2) (1458818-00-B).

    33.5 N.m (24.7 lbs-ft) 

    Tip: Use of the following tool(s) is recommended:

    • Cordless Ratchet/Impact Driver
    • Torx T45 socket
    • Torx Plus T45 socket
    • Flex head ratchet/flex head torque wrench (for installation only)
    G16588812Courtesy of TESLA, INC.
  18. Raise the LH rear window and close the LH rear door.
  19. Install the lower A-pillar assembly. See A - B - C POST INTERIOR TRIM - A - PILLAR LOWER ASSEMBLY, LH - REMOVE AND REPLACE .
  20. Install the LH instrument panel end cap. See DASH PANEL - END CAP, LH - REMOVE AND REPLACE .
  21. Install the rear underhood apron. See UNDERHOOD TRIM - REAR APRON ASSEMBLY - REMOVE AND REPLACE .
  22. Move the LH front seat to original position.
  23. Raise the LH front window and close the LH front door.
scientia non olet · About LEMON Manuals