LEMON Manuals: Even more car manuals for everyone
Home >> Tesla >> 2022 >> Model X Base >> Repair and Diagnosis (Single Page) >> Accessories & Equipment >> Seats >> Seats (1 Of 2) -- Model X >> 2nd Row Seat Tracks And Motors >> Release Cable - EZ Entry - 2nd Row - RH (7 Seat) - Remove And Replace >> Install

Release Cable - EZ Entry - 2nd Row - RH (7 Seat) - Remove And Replace: Install

  1. Position the RH 2nd row EZ entry release cable into the RH 2nd row seat.
    G15402496Courtesy of TESLA, INC.
    G15402497Courtesy of TESLA, INC.
    G15402498Courtesy of TESLA, INC.
  2. Secure the clips (x2) that attach the RH 2nd row EZ entry release cable to the outer track actuator.

    Tip: Firmly press the cable clip into the cable retainer until the cable is secured to the track actuator.

    G15402499Courtesy of TESLA, INC.
  3. Install cable onto 40 RH inner track actuator
    NOTE: 2x clips, Firmly press cable clip into cable retainer till cable is secured to track actuator
    G15402500Courtesy of TESLA, INC.
  4. Secure the cable clips (x2) at the RH 2nd row seat RH side of the seat riser.
    G15402501Courtesy of TESLA, INC.
  5. Position the inboard and outboard seat riser covers to the RH 2nd row inboard seat riser, and then secure the clips (x2) that attach the covers to the seat riser. Repeat this step for the outboard seat riser.
    G15402502Courtesy of TESLA, INC.
    G13957042Courtesy of TESLA, INC.
    G15402503Courtesy of TESLA, INC.
    G13957043Courtesy of TESLA, INC.
  6. Install the screws (x3) that attach the inboard seat riser cover to the RH 2nd row outboard seat riser.

    Tip: Use of the following tool(s) is recommended:

    • T20 socket
    G15402505Courtesy of TESLA, INC.
  7. Install the screw that attaches the outboard seat riser cover to the RH 2nd row outboard seat riser.

    Tip: Use of the following tool(s) is recommended:

    • T20 socket
    G15402506Courtesy of TESLA, INC.
  8. Repeat steps  6 and  7 for the inboard seat riser.
  9. Reinstall the lower portion of the seat back cushion.
    G15402507Courtesy of TESLA, INC.
  10. Fold the RH 2nd row seat to the down position.
  11. Install the cable end fitting into the slider.
    CAUTION: Be careful not to kink or damage the cable.
    NOTE: Install the cable vertically. Use bent needle nose pliers to hold the cable end fitting in place, and then insert the end fitting into the slider opening.
    G15402508Courtesy of TESLA, INC.
    G15402509Courtesy of TESLA, INC.
    G15402510Courtesy of TESLA, INC.
    G15402511Courtesy of TESLA, INC.
    G15402512Courtesy of TESLA, INC.
  12. Secure the actuator cable to the actuator slide assembly.
    CAUTION: Be careful not to damage the cable locating plastic.
    G15402513Courtesy of TESLA, INC.
  13. Install the clip that attaches the RH 2nd row seat actuator slider assembly to the seat frame.
    G15402514Courtesy of TESLA, INC.
  14. Secure the clip that attaches the RH 2nd row seat actuator slider assembly to the seat frame.
    G15402515Courtesy of TESLA, INC.
  15. Install a new metal clip into the RH 2nd row seat actuator slider assembly.
    CAUTION: Be careful not to deform or damage the clip.
    NOTE: Apply forward pressure to the slider to install the metal clip.
    NOTE: Verify operation to ensure proper functionality.

    Tip: Use the flat side of a plastic trim tool to aid in installation.

    G15402516Courtesy of TESLA, INC.
    G15402517Courtesy of TESLA, INC.
    G15402518Courtesy of TESLA, INC.
    G15402519Courtesy of TESLA, INC.
  16. Secure the clip that attaches the RH 2nd row seat harness to the seat frame.
    G15402520Courtesy of TESLA, INC.
  17. Secure the clip that attaches the RH 2nd row seat heater connector to the seat frame.
    G15402521Courtesy of TESLA, INC.
  18. Connect the RH 2nd row seat heater electrical connector.
    G15402522Courtesy of TESLA, INC.
  19. Position the RH 2nd row seat back plastic to the seat back assembly, and then secure the clips (x5) that attach the seat back plastic to the assembly.
    G15402523Courtesy of TESLA, INC.
    G15402524Courtesy of TESLA, INC.
  20. Fold the seat back upholstery into position, secure the Velcro strips (x2), and then zip the upholstery on the LH and RH sides of backrest cover.
    NOTE: The ends of zippers are tucked underneath the upholstery.

    Tip: Use a pick to help move the zipper.

    G15402525Courtesy of TESLA, INC.
    G15402526Courtesy of TESLA, INC.
    G15402527Courtesy of TESLA, INC.
    G15402528Courtesy of TESLA, INC.
  21. Secure the J-hook that attaches the RH 2nd row seat back upholstery to the seat assembly.
    G15402529Courtesy of TESLA, INC.
    G15402530Courtesy of TESLA, INC.
    G15402531Courtesy of TESLA, INC.
    G15402532Courtesy of TESLA, INC.
  22. Position the RH 2nd row seat cushion into the seat assembly.
    NOTE: Guide the harness and tension flaps underneath the seat back.
    G15402533Courtesy of TESLA, INC.
    G15402534Courtesy of TESLA, INC.
    G15402535Courtesy of TESLA, INC.
  23. Secure the clip that attaches the seat harness to the RH 2nd row seat assembly, and then connect the heater and seat belt reminder electrical connectors.
    G15402536Courtesy of TESLA, INC.
    G15402537Courtesy of TESLA, INC.
  24. Secure the J-clips (x6) that attach the RH 2nd row seat cushion trim to the seat bracket assembly.
    G15402538Courtesy of TESLA, INC.
    G15402539Courtesy of TESLA, INC.
  25. Slide the upper tabs of the RH 2nd row seat inner hinge cover onto the seat frame, and then secure the clip and tabs (x4) that attach the cover to the seat assembly.
    G15402540Courtesy of TESLA, INC.
    G15402541Courtesy of TESLA, INC.
  26. Position the RH 2nd row seatbelt buckle to the seat assembly, and then install the bolt that attaches the buckle to the assembly.

    45 N.m (33.2 ft-lbs) 

    Tip: Use of the following tool(s) is recommended:

    • T50 socket
    G15402542Courtesy of TESLA, INC.
  27. Secure the clips (x2) that attach the RH 2nd row seatbelt buckle connector and harness to the seat assembly, and then connect the seatbelt buckle connector.
    G15402543Courtesy of TESLA, INC.
    G15402544Courtesy of TESLA, INC.
  28. Position the RH 2nd row seatbelt to the seat assembly, and then install a new bolt that attaches the seatbelt to the assembly.

    45 N.m (33.2 ft-lbs) 

    Tip: Use of the following tool(s) is recommended:

    • T50 socket
    G15402545Courtesy of TESLA, INC.
  29. Install the RH 2nd row recliner cover. See COVER - RECLINER - 2ND ROW - LH (REMOVE AND REPLACE) .
  30. Install the RH 2nd row recliner lever. See LEVER - RECLINER - 2ND ROW - LH (REMOVE AND REPLACE) .
  31. Fold the RH 2nd row seat back to the down position.
  32. Install the RH 2nd row seat assembly. See SEAT ASSEMBLY - 2ND ROW - RH (7 SEAT) (REMOVE AND REPLACE) .
    NOTE: It is not necessary to redeploy software after install.
scientia non olet · About LEMON Manuals