LEMON Manuals: Even more car manuals for everyone
Home >> Tesla >> 2021 >> Model X Plaid >> Repair and Diagnosis (Single Page) >> Accessories & Equipment >> Seats >> Seats (2 Of 2) -- Model X >> Front Seat Covers, Pads, And Trims >> Cover - Back Rest - Driver - Remove And Replace >> Install

Cover - Back Rest - Driver - Remove And Replace: Install

  1. Position the driver seat back rest trim onto the driver seat back rest foam, and then align the Velcro strips (x4).
    G15404838Courtesy of TESLA, INC.
    G15404839Courtesy of TESLA, INC.
    G15404840Courtesy of TESLA, INC.
  2. Carefully install the airbag into the airbag chute.
    CAUTION: Make sure that the driver side airbag mounting studs extend out of the holes of the chute.
    CAUTION: Handle the airbag with extreme care when installing it into the airbag chute. The airbag is configured/folded in a specific manner and will need to be replaced if it is dropped, altered or manipulated in any way.
    NOTE: Refer to the following video for proper care when installing the driver side airbag into the airbag chute, and when installing the chute through the seat foam.
    multimedia:A supplement to the article is available.
    G15404842Courtesy of TESLA, INC.
  3. Carefully position the air bag chute into the LH side of the seat back foam, and then fold the seat back trim over the LH side bolster.
    G15404843Courtesy of TESLA, INC.
  4. With assistance, maneuver the driver seat back trim assembly downward onto the seat frame to install it onto the seat assembly.
    G15404844Courtesy of TESLA, INC.
  5. Install the clip that attaches the driver seat harness to the RH side of seat back frame.
    G15404845Courtesy of TESLA, INC.
  6. Carefully secure the RH side of the driver seat back trim onto the driver seat frame.
    G15404846Courtesy of TESLA, INC.
    G15404847Courtesy of TESLA, INC.
  7. Install new nuts (x2) that attach the driver seat side air bag to the seat back frame assembly.

    5.4 N.m (4.0 ft-lbs) 

    Tip: Use of the following tool(s) is recommended:

    • 11 mm socket
    G15404848Courtesy of TESLA, INC.
    G15404849Courtesy of TESLA, INC.
  8. Fasten the tabs (x2) that attach the lower portion of the driver seat backrest lumbar support to the seat back frame.
    G15404850Courtesy of TESLA, INC.
  9. Install the bolt that attaches the driver seat backrest lumbar support to the seat back frame.

    5 N.m (3.7 ft-lbs) 

    Tip: Use of the following tool(s) is recommended:

    • 10 mm socket
    G15404851Courtesy of TESLA, INC.
  10. Install the clip that attaches the driver seat side airbag harness to the driver seat seat frame.
    G15404852Courtesy of TESLA, INC.
  11. Connect the driver seat side air bag electrical connector, and then secure the safety lock.
    G15404853Courtesy of TESLA, INC.
    G15404854Courtesy of TESLA, INC.
  12. Carefully secure the LH side of the driver seat seat cover and foam onto the seat frame.
    G15404855Courtesy of TESLA, INC.
    G15404856Courtesy of TESLA, INC.
  13. Secure the retainers (x6), and then secure the trim strap onto the driver seat seat back frame.
    G15404857Courtesy of TESLA, INC.
  14. Secure the female side of microphone connector and harness clips (x2) onto seat back suspension.
    G15404858Courtesy of TESLA, INC.
    G15404859Courtesy of TESLA, INC.
  15. Connect the driver seat microphone, and then secure harness clip onto the seat back foam.
    G15404860Courtesy of TESLA, INC.
    G15404861Courtesy of TESLA, INC.
  16. Slide the fan controller electrical connector downward to install it onto the bracket, and then connect the electrical connector.
    G15404862Courtesy of TESLA, INC.
  17. With assistance, align and fully secure the clips that attach the driver seat back shell to the seat assembly.
    G15404863Courtesy of TESLA, INC.
    G15404864Courtesy of TESLA, INC.
    G15404865Courtesy of TESLA, INC.
  18. Install the driver headrest trim. See TRIM - HEADREST - DRIVER (REMOVE AND REPLACE) .
  19. Position the driver seat assembly onto the seat back.
    NOTE: Protect the seat from damage.
  20. Secure the clip and bracket that attach the FSC and FSB vent heat pad harnesses to the seat assembly.
    NOTE: One harness is for the seat cushion and the other is for the seat back. The upper bracket aids in routing while the lower clip secures them.
    G15404866Courtesy of TESLA, INC.
  21. Connect the FSB vent heat pad electrical connector from the seat controller.
    G15404867Courtesy of TESLA, INC.
  22. Secure the seat back elastic straps (x2) to the seat frame.
    G15404868Courtesy of TESLA, INC.
  23. Install the front seat side shield RH carrier from the driver seat. See CARRIER - RH - SIDE SHIELD - INBOARD - FRONT SEAT (REMOVE AND REPLACE) .
  24. Install the driver seat inboard side shield. See SIDE SHIELD - INBOARD - DRIVER SEAT (REMOVE AND REPLACE) .
  25. Install the front seat side shield LH carrier from the driver seat. See CARRIER - LH - SIDE SHIELD - OUTBOARD - FRONT SEAT (REMOVE AND REPLACE) .
  26. Connect the electrical harness to the back rest and cushion adjust switch assembly, and then verify the functions of the seat switches.
    G15404870Courtesy of TESLA, INC.
  27. Position the driver seat outboard side shield onto the seat, and then install the clips (x7) that attach the side shield to the seat.

    Tip: Apply pressure to the side shield to fully seat the clips. The side shield should sit flush against the seat cushion.

    G13957048Courtesy of TESLA, INC.
  28. Install the screw that attaches the driver seat outboard side shield to the seat assembly.

    4 N.m (2.9 ft-lbs) 

    Tip: Use of the following tool(s) is recommended:

    • Torx T20 socket
    • 2 in extension
    • Ratchet/torque wrench
    G15404871Courtesy of TESLA, INC.
  29. Install the driver seat into the vehicle. See SEAT ASSEMBLY - 1ST ROW - LH (REMOVE AND INSTALL) .
scientia non olet · About LEMON Manuals