- Install LH headlamp into vehicle.
NOTE:
Caution not to damage any component during installation.
 Courtesy of TESLA, INC.
|
 Courtesy of TESLA, INC.
|
 Courtesy of TESLA, INC.
|
- Install bolts securing LH headlamp to vehicle.
NOTE:
4x bolts, 10 mm, 5.9 N.m.
 Courtesy of TESLA, INC.
|
 Courtesy of TESLA, INC.
|
 Courtesy of TESLA, INC.
|
- Connect LH headlamp connector.
NOTE:
1x connector, Secure connector and fully engage red locking tab.
 Courtesy of TESLA, INC.
|
 Courtesy of TESLA, INC.
|
- Install front fascia onto vehicle and secure fascia to fender brackets.
NOTE:
Recommend Assistance, Route fascia harness while installing, Verify front fascia valance sits under front aero shield before proceeding.
 Courtesy of TESLA, INC.
|
 Courtesy of TESLA, INC.
|
- Apply Loctite 222 to fasteners and secure front fascia valance to front aero shield.
NOTE:
3x bolts, 10 mm, 6 N.m, 2x clips, 2x datums, Insert valance datums into aero shield holes, Do not remove 3x middle bolts.
 Courtesy of TESLA, INC.
|
 Courtesy of TESLA, INC.
|
 Courtesy of TESLA, INC.
|
- Connect front fascia harness.
NOTE:
2x connectors, Engage locking tab, Located behind RH wheel arch liner.
 Courtesy of TESLA, INC.
|
- Install bolt securing fascia to RH fender bracket.
NOTE:
1x bolt, T25, 5 N.m.
 Courtesy of TESLA, INC.
|
- Install push clips securing RH front wheel liner to fascia.
NOTE:
5x push clips.
 Courtesy of TESLA, INC.
|
 Courtesy of TESLA, INC.
|
- Connect First Responder Loop and LV battery connector.
NOTE:
2x connectors Secure FRL first, Seat LV battery connection and push black connector lock inwards to secure, Engage green locking tab when fully seated.
 Courtesy of TESLA, INC.
|
 Courtesy of TESLA, INC.
|
 Courtesy of TESLA, INC.
|
 Courtesy of TESLA, INC.
|
- Press brake pedal to turn on drive rails.
 Courtesy of TESLA, INC.
|
- Turn wheel fully to the right.
 Courtesy of TESLA, INC.
|
- Install bolt securing fascia to LH fender bracket.
NOTE:
1x bolt, T25, 5 N.m.
 Courtesy of TESLA, INC.
|
- Install push clips securing LH front wheel liner to fascia.
NOTE:
5x push clips.
 Courtesy of TESLA, INC.
|
 Courtesy of TESLA, INC.
|
- Install bolts securing fascia bracket to carrier.
NOTE:
6x bolts, 10 mm, 4 N.m.
 Courtesy of TESLA, INC.
|
- Install front underhood apron.
NOTE:
7x clips.
 Courtesy of TESLA, INC.
|
 Courtesy of TESLA, INC.
|
- Press brake pedal to turn on drive rails.
 Courtesy of TESLA, INC.
|
- Turn steering wheel back to center.
 Courtesy of TESLA, INC.
|
- Release IP service panel.
NOTE:
2x tabs, 4x datums, Release top tabs and slide rearward.
 Courtesy of TESLA, INC.
|
 Courtesy of TESLA, INC.
|
 Courtesy of TESLA, INC.
|
- Using laptop connect to vehicle with ethernet diag kit and Toolbox 3.
NOTE:
Open Toolbox 3 website and establish connection to the vehicle. Ethernet connection will provide communication.
 Courtesy of TESLA, INC.
|
 Courtesy of TESLA, INC.
|
 Courtesy of TESLA, INC.
|
- Select 'Actions/Autodiag' and search for 'Redeploy'.
 Courtesy of TESLA, INC.
|
- Select 'SERVICE CAN REDEPLOY', click 'Run', and allow routine to complete.
NOTE:
Select 'X' at top right of window to close once complete, Routine will state pass but update will continue to run in the background, UI will indicate status of update.
 Courtesy of TESLA, INC.
|
 Courtesy of TESLA, INC.
|
 Courtesy of TESLA, INC.
|
 Courtesy of TESLA, INC.
|
 Courtesy of TESLA, INC.
|
- Disconnect Toolbox 3 from vehicle and remove laptop and ethernet diag kit.
 Courtesy of TESLA, INC.
|
 Courtesy of TESLA, INC.
|
 Courtesy of TESLA, INC.
|
- Install IP service panel.
NOTE:
2x tabs, 4 datums, Slide forward engaging datums then secure tabs upward into IP.
 Courtesy of TESLA, INC.
|
 Courtesy of TESLA, INC.
|
- Install RH underhood apron.
NOTE:
10x clips.
 Courtesy of TESLA, INC.
|
 Courtesy of TESLA, INC.
|
- Install LH underhood apron.
NOTE:
10x clips.
 Courtesy of TESLA, INC.
|
 Courtesy of TESLA, INC.
|
- Install rear underhood apron.
NOTE:
8x clips.
 Courtesy of TESLA, INC.
|
 Courtesy of TESLA, INC.
|
- Close hood.
- Enter the vehicle and close LH front door.
 Courtesy of TESLA, INC.
|
- Set air suspension ride height to "Medium" and place into Jack Mode.
NOTE:
Using center display, Controls > Suspension > "Medium", Using center display, Controls > Service > "Jack Mode".
 Courtesy of TESLA, INC.
|
 Courtesy of TESLA, INC.
|
- Open LH front door then exit vehicle.
 Courtesy of TESLA, INC.
|
- Apply tape to wall 27.126 inches (68.9 cm) from the ground.
 Courtesy of TESLA, INC.
|
- Apply tape to floor 25 feet (7.6 m) from the wall.
 Courtesy of TESLA, INC.
|
- Park vehicle on flat level surface perpendicular to wall and align front fascia with tape on floor.
NOTE:
Choose a dark work area with low ambient lighting for best results, Ensure tire pressure is set to specification.
 Courtesy of TESLA, INC.
|
- Project a laser perpendicular to the wall onto the center point of the vehicle, then mark a center-line on the wall.
 Courtesy of TESLA, INC.
|
 Courtesy of TESLA, INC.
|
- Measure 78 cm and make a mark on both sides of the center-line.
NOTE:
These reference marks will be the targets for horizontal adjustment.
 Courtesy of TESLA, INC.
|
- Select Adjust Headlights using center display.
NOTE:
Via Controls > Service > Adjust Headlights, Use scroll wheel to adjust, Note Service Mode is required for the horizontal adjustment.
 Courtesy of TESLA, INC.
|
 Courtesy of TESLA, INC.
|
- Adjust LH headlight beam.
NOTE:
Adjust LH headlight so that top of horizontal beam aligns with tape mark on wall, Do not sit in vehicle as this will affect headlamp height.
 Courtesy of TESLA, INC.
|
 Courtesy of TESLA, INC.
|
 Courtesy of TESLA, INC.
|
- Adjust RH head lamp beam.
NOTE:
Adjust RH headlight so that top of horizontal beam aligns with tape mark on wall, Do not sit in vehicle as this will affect headlamp height.
 Courtesy of TESLA, INC.
|
 Courtesy of TESLA, INC.
|
 Courtesy of TESLA, INC.
|
- Exit Headlight adjustment using center display.
NOTE:
Select X at the top left of menu to exit adjustment mode.
 Courtesy of TESLA, INC.
|