LEMON Manuals: Even more car manuals for everyone
Home >> Tesla >> 2021 >> Model S Performance >> Repair and Diagnosis (Single Page) >> Accessories & Equipment >> Gauges & Instrument Panels >> Instrument Panel -- Model S >> Instrument Panel >> Glove Box - Remove And Replace >> Install

Glove Box - Remove And Replace: Install

  1. Route the glove box shape memory alloy (SMA) latch manual release cable into glove box housing, secure the harness into the mounting points (x2), and then insert the SMA assembly arms into the glove box door.
    G15083847Courtesy of TESLA, INC.
    G15083848Courtesy of TESLA, INC.
    G15083849Courtesy of TESLA, INC.
    G15083850Courtesy of TESLA, INC.
    G15083851Courtesy of TESLA, INC.
  2. Position the glove box shape memory alloy (SMA) latch assembly into the glove box assembly, and then install the screws (x2) that attach the SMA to the glove box assembly.

    2 N.m (1.5 ft-lbs) 

    Tip: Use of the following tool(s) is recommended:

    • T20 socket
    G15083852Courtesy of TESLA, INC.
  3. Position the inboard and outboard shape memory alloy (SMA) locator plates to the glove box assembly, and then install the screws (x4) that attach the plates to the assembly.

    2 N.m (1.5 ft-lbs) 

    Tip: Use of the following tool(s) is recommended:

    • T20 socket
    G15083853Courtesy of TESLA, INC.
    G15083854Courtesy of TESLA, INC.
  4. Position the USB outlet into the glove box, and then install the screws (x2) and secure the clip that attaches the outlet to the glove box.

    3 N.m (2.2 ft-lbs) 

    NOTE: Make sure the USB socket is flush in the glove box.

    Tip: Use of the following tool(s) is recommended:

    • T20 socket
    G15083855Courtesy of TESLA, INC.
    G15083856Courtesy of TESLA, INC.
  5. Connect the glove box electrical connectors (x3).
    G15083857Courtesy of TESLA, INC.
  6. Position the glove box into the instrument panel, and then install the screws (x5) that attach the glove box to the instrument panel.

    3 N.m (2.2 ft-lbs) 

    NOTE: Install the screws at the top of the glove box first, and then close the lid to install the bottom screws. Use the manual release to open glove box if needed.

    Tip: Use of the following tool(s) is recommended:

    • T20 socket
    G15083858Courtesy of TESLA, INC.
    G15083859Courtesy of TESLA, INC.
  7. While supporting the front passenger knee airbag assembly, connect the electrical connectors (x2).
    CAUTION: Carefully connect the airbag electrical connector to prevent damage to the electrical connectors.
    G15083860Courtesy of TESLA, INC.
  8. Hook the tabs (x6) before putting the front passenger knee airbag onto the instrument panel, and then seat the airbag to the instrument panel.
  9. Install the new patch bolts (x2) that attach the front passenger knee airbag to the instrument panel.

    8 N.m (5.9 ft-lbs) 

    Tip: Use of the following tool(s) is recommended:

    • 2 in extension
    • Ratchet/torque wrench
    • External Torx E10
    • 1/4 in to 3/8 in adapter
    G15083861Courtesy of TESLA, INC.
  10. Install the passenger footwell cover. See Cover - Footwell - Passenger (Remove And Replace) .
  11. Install the RH instrument panel middle trim. See Trim - Middle - Instrument Panel - RH (Remove And Replace) .
  12. Connect LV power. See LV Power (Disconnect and Connect) .
  13. Install the rear underhood apron. See Underhood Apron - Rear (Remove and Replace) .
scientia non olet · About LEMON Manuals