LEMON Manuals: Even more car manuals for everyone
Home >> Suzuki >> 2001 >> XL-7 Limited >> Repair and Diagnosis >> External Pages >> Different car >> Section 17 (Engine Controls - Self-Diagnostics) >> Diagnostic Tests >> DTC P0134: Heated Oxygen Sensor Bank No. 1 (Left Bank), Sensor No. 1 (B1 S1) Circuit, No Activity Detected >> Diagnosis & Repair Procedure

Diagnosis & Repair Procedure

WARNING: This page is about a different car, the 2002 Suzuki Grand Vitara. However, it is still accessible from the selected car via links, so may be relevant.
  1. Check for DTCs P0101, P0102, P0103, P0116, P0117, P0118, and P0135. See RETRIEVING DIAGNOSTIC TROUBLE CODES  under SELF-DIAGNOSTIC SYSTEM. If DTCs are not set, go to next step. If any DTC is set, go to that test first.
  2. Perform DTC CONFIRMATION TEST  . If DTC P0134 is set, go to next step. If DTC P0134 is not set, problem is intermittent. System is okay at this time. See INTERMITTENTS TROUBLE SHOOTING - NO CODES article.
  3. Check fuel gauge. If fuel gauge indicates "E", add fuel and recheck. If fuel gauge does not indicate "E", go to next step.
  4. Turn ignition off. Connect scan tool. Drive vehicle for one minute or more with engine speed at 2000 RPM or more and with engine coolant temperature at 158°F (70°C) or more. Observe HO2S Bank 1, Sensor 1 parameter on scan tool. If display does not toggle above and below .5 volt, go to next step. If display toggles above and below .5 volt, problem is intermittent. System is okay at this time. See INTERMITTENTS TROUBLE SHOOTING - NO CODES article. If intermittent problem is not found, replace ECM (PCM) and go to DTC CONFIRMATION TEST  .
  5. Backprobing, measure voltage between ECM (PCM) 26-pin connector C51-3 terminals No. 4 (Red wire) and No. 21 (Gray/Yellow wire). See Figure . Start engine. Observe voltage while revving engine several times. If reading are not .5 volt or more, go to next step. If readings are .5 volt or more, disconnect ECM (PCM) 26-pin connector C51-3. Check for poor terminal contact at ECM (PCM) 26-pin connector C51-3. If poor terminal contact is found, repair as necessary and go to DTC CONFIRMATION TEST  . If terminal contact is okay, replace ECM (PCM) and go to DTC CONFIRMATION TEST  .
  6. Check for short or open in Red wire between HO2S Bank 1, Sensor 1 and ECM (PCM) 26-pin connector C51-3 terminals No. 4. Also check for short or open in Gray/Yellow wire between HO2S Bank 1, Sensor 1 and ECM (PCM) 26-pin connector C51-3 terminals No. 21. See ENGINE PERFORMANCE in SYSTEM WIRING DIAGRAMS article in ELECTRICAL. Repair as necessary and go to DTC CONFIRMATION TEST  . If wires are okay, go to next step.
  7. Check fuel injector circuit operation. See B-1: FUEL INJECTOR CIRCUIT INSPECTION in BASIC DIAGNOSTIC PROCEDURES article. Repair as necessary and go to DTC CONFIRMATION TEST  . If fuel injector circuit is okay, go to next step.
  8. Check fuel injector resistance on cylinders No. 1, 3 and 5. See INJECTOR RESISTANCE in SERVICE & ADJUSTMENT SPECIFICATIONS article. Replace injector(s) as necessary. If fuel injector resistance is okay, go to next step.
  9. Perform fuel pressure test. See FUEL SYSTEM in BASIC DIAGNOSTIC PROCEDURES article. Repair as necessary and go to DTC CONFIRMATION TEST  . If fuel pressure is okay, replace HO2S Bank 1, Sensor 1 and go to DTC CONFIRMATION TEST  . If problem still persists, replace ECM (PCM) and go to DTC CONFIRMATION TEST  .
scientia non olet · About LEMON Manuals