LEMON Manuals: Even more car manuals for everyone
Home >> Subaru >> 2022 >> WRX Premium, Standard Trans >> Repair and Diagnosis >> External Pages >> Different variant/trim >> Section 1 (CVT Transaxle (Tr690)) >> General Description >> Preparation Tool >> SUBARU Special Tool

SUBARU Special Tool

WARNING: This page is about a different variant/trim than selected.
ILLUSTRATION TOOL NUMBER DESCRIPTION REMARKS
G13603041Courtesy of SUBARU OF AMERICA, INC.
 398177700 INSTALLER
  • Used for installing the ball bearing of reduction driven gear.
  • Used for installing the bearing retainer.
  • Used for installing the ball bearing of the reduction driven gear side in the transmission case.
    NOTE:

    Used together with INSTALLER (20099AE020). 

  • Used for installing the ball bearing (rear side) of the front reduction drive gear.
    NOTE:

    Used together with INSTALLER (499757002). 
G13603043Courtesy of SUBARU OF AMERICA, INC.
 398497701 SEAT
  • Used for removing the transfer reduction driven gear.
    NOTE:

    Used together with REMOVER (498077600) and REMOVER (899864100). 

  • Used for removing the reduction driven gear.
    NOTE:

    Used together with REMOVER (498077600) and REMOVER (899864100). 

  • Used for removing and installing the ball bearing of reduction driven gear.
    NOTE:

    Used together with REMOVER (498077600) and REMOVER (899864100). 

  • Used for removing and installing the side bearing inner race.
    NOTE:
    • Used together with PULLER ASSY (399703600) when removing. 
    • Used together with BUSHING 1-2 INSTALLER (499277100) when installing. 
G13591889Courtesy of SUBARU OF AMERICA, INC.
 398527700 PULLER ASSY
  • Used for removing the roller bearing of the primary pulley side in the transmission case.
  • Used for removing the roller bearing of the secondary pulley side in the transmission case.
    NOTE:

    Used together with CLAW (18760AA000). 

  • Used for removing the ball bearing of the reduction driven gear side in the transmission case.
  • Used for removing the side bearing outer race.
  • Used for removing the ball bearing of the converter case cover.
    NOTE:

    Used together with CLAW (18760AA000). 
G05002451Courtesy of SUBARU OF AMERICA, INC.
 398744300 PISTON GUIDE Used for adjusting the transfer clutch driven plate No. 3.
G13603046Courtesy of SUBARU OF AMERICA, INC.
 399703600 PULLER ASSY
  • Used for removing the side bearing inner race.
    NOTE:

    Used together with SEAT (398497701). 

  • PULLER ASSY (399703601) can also be used.
G13591892Courtesy of SUBARU OF AMERICA, INC.
 498057300 INSTALLER Used for installing the extension case oil seal.
G13591895Courtesy of SUBARU OF AMERICA, INC.
 498077400 REMOVER
  • Used for removing the ball bearing of the rear drive shaft.
  • Used for removing the ball bearing (rear side) of front reduction drive gear.
    NOTE:

    Used together with REMOVER (899864100). 
G13591896Courtesy of SUBARU OF AMERICA, INC.
 498077600 REMOVER
  • Used for removing the ball bearing of drive sprocket.
    NOTE:

    Used together with HOUSING BUSHING INSTALLER AND REMOVER (927720000). 

  • Used for removing the ball bearing of transfer reduction driven gear.
    NOTE:

    Used together with SEAT (398497701) and REMOVER (899864100). 

  • Used for removing ball bearing of reduction driven gear.
    NOTE:

    Used together with SEAT (398497701) and REMOVER (899864100). 

  • Used for removing the taper roller bearing inner race (front side) of drive pinion.
  • Used for removing the ball bearing (front side) of the front reduction drive gear.
G13591897Courtesy of SUBARU OF AMERICA, INC.
 498255400 PLATE Used for measuring the backlash of the hypoid gear set.
G13591898Courtesy of SUBARU OF AMERICA, INC.
 498277200 STOPPER SET Used for removing and installing transmission body.
G13591899Courtesy of SUBARU OF AMERICA, INC.
 498497300 CRANKSHAFT STOPPER Used for removing and installing the drive plate.
G13591901Courtesy of SUBARU OF AMERICA, INC.
 498575400 OIL PRESSURE GAUGE ASSY Used for measuring the transfer clutch pressure.
NOTE:
  • Used together with PRESSURE GAUGE ADAPTER (18681AA000), ADAPTER HOSE A (34099AC010) and ADAPTER HOSE B (34099AC020). 
  • Use the genuine O-ring (part No. 806908150) for installation. 
G13199921Courtesy of SUBARU OF AMERICA, INC.
 498897700 OIL PRESSURE ADAPTER SET
  • Used for measuring the secondary pressure.
    NOTE:

    Used together with PRESSURE GAUGE ADAPTER (18681AA000) and OIL PRESSURE GAUGE ASSY (18801AA000). 

  • Used for measuring line pressure.
    NOTE:

    Used together with PRESSURE GAUGE ADAPTER (18681AA010) and OIL PRESSURE GAUGE ASSY (18801AA000). 
G13591904Courtesy of SUBARU OF AMERICA, INC.
 499267300 STOPPER PIN Used for adjusting the inhibitor switch.
G13591905Courtesy of SUBARU OF AMERICA, INC.
 499277100 BUSHING 1-2 INSTALLER
  • Used to install the rear drive shaft ball bearing.
    NOTE:

    Used together with INSTALLER (499757002). 

  • Used for installing the ball bearing of the transfer reduction driven gear.
  • Used for installing the side bearing inner race.
    NOTE:

    Used together with SEAT (398497701). 
G13591906Courtesy of SUBARU OF AMERICA, INC.
 499277200 INSTALLER Used for installing the taper roller bearing inner race (front side) of drive pinion.
G13591907Courtesy of SUBARU OF AMERICA, INC.
 499575400 GAUGE
  • Used for adjusting the primary pulley shim.
  • Used for adjusting the rear drive shaft shim.
  • Used for adjusting the transfer clutch driven plate No. 3.
  • Used for adjusting the front reduction drive gear shim.
  • Used for adjusting the front reduction driven gear shim (front side).
G13591909Courtesy of SUBARU OF AMERICA, INC.
 499575600 GAUGE
  • Used for adjusting the transfer reduction driven gear shim.
  • Used for adjusting the forward clutch drum washer.
  • Used for adjusting the forward clutch washer.
    NOTE:

    Used together with PULLER SET (499737100). 

  • Used for inspecting clutch clearance.
    NOTE:

    Used together with OIL SEAL INSTALLER (398437700). 

  • Used for adjusting the drive pinion shim.
  • Used for adjusting the front reduction drive gear shim.
  • Used for adjusting the front reduction driven gear shim (front side).
G13621832Courtesy of SUBARU OF AMERICA, INC.
 499737100 PULLER SET Used for adjusting the forward clutch washer.
NOTE:
  • Use the rack only. 
  • Used together with GAUGE (499575600). 
G13591911Courtesy of SUBARU OF AMERICA, INC.
 499755602 PRESS SNAP RING Used for installing the roller bearing of the secondary pulley side in the transmission case.
NOTE:

Used together with INSTALLER (20099AE020). 
G13591912Courtesy of SUBARU OF AMERICA, INC.
 499757002 INSTALLER
  • Used to install the rear drive shaft ball bearing.
    NOTE:

    Used together with BUSHING 1-2 INSTALLER (499277100). 

  • Used for installing the ball bearing (rear side) of the front reduction drive gear.
    NOTE:

    Used together with INSTALLER (398177700). 
G13591914Courtesy of SUBARU OF AMERICA, INC.
 499787700 WRENCH
  • Used for adjusting hypoid gear set backlash.
    NOTE:

    Used together with HOLDER (18667AA010). 

  • Used for checking and adjusting the tooth contact of hypoid gear set.
    NOTE:

    Used together with HOLDER (18667AA010). 

  • Used for removing and installing the drive pinion lock nut.
    NOTE:

    Used together with HOLDER (18667AA010). 
G13591917Courtesy of SUBARU OF AMERICA, INC.
 899864100 REMOVER
  • Used for removing the transfer reduction driven gear.
    NOTE:

    Used together with SEAT (398497701) and REMOVER (498077600). 

  • Used for removing the reduction driven gear.
    NOTE:

    Used together with SEAT (398497701) and REMOVER (498077600). 

  • Used for removing the ball bearing (rear side) of front reduction drive gear.
    NOTE:

    Used together with REMOVER (498077400). 
G13591918Courtesy of SUBARU OF AMERICA, INC.
 899904100 STRAIGHT PIN REMOVER Used for removing the spring pin.
G13591920Courtesy of SUBARU OF AMERICA, INC.
 927720000 HOUSING BUSHING INSTALLER AND REMOVER
  • Used for installing the oil seal of the oil pump chain cover.
    NOTE:

    Use BUSHING SHAFT (927880000) and BASE TUBE LATERAL LINK (927890000). 

  • Used for removing the ball bearing of drive sprocket.
    NOTE:
    • Use BUSHING SHAFT (927880000). 
    • Used together with REMOVER (498077600). 
G13591921Courtesy of SUBARU OF AMERICA, INC.
 18270AA040 SOCKET Used for removing and installing the test plug (transfer clutch pressure).
NOTE:

Used together with SPECIAL TOOL CONDENSER (73099SG000). 
G13602209Courtesy of SUBARU OF AMERICA, INC.
 18270KA020 SOCKET (E20) Used for removing and installing the drive pinion retainer.
G13591925Courtesy of SUBARU OF AMERICA, INC.
 18460AA040 CHECK BOARD Used for measuring voltage and resistance of TCM terminals.
G13591926Courtesy of SUBARU OF AMERICA, INC.
 18632AA000 STAND ASSY
  • Used for removing the transmission harness.
  • Used for disassembling and assembling the transmission body.
G13621844Courtesy of SUBARU OF AMERICA, INC.
 18651AA000 INSTALLER Used for installing the ball bearing (front side) of the front reduction drive gear.
G13591927Courtesy of SUBARU OF AMERICA, INC.
 18657AA000 INSTALLER Used for installing the oil seal of inhibitor switch.
G13591433Courtesy of SUBARU OF AMERICA, INC.
 18658AA021 WRENCH COMPL RETAINER
  • Used for removing and installing the differential side retainer.
  • Used for adjusting hypoid gear set backlash.
G13621847Courtesy of SUBARU OF AMERICA, INC.
 18667AA010 HOLDER
  • Used for adjusting hypoid gear set backlash.
    NOTE:

    Used together with WRENCH (499787700). 

  • Used for checking and adjusting the tooth contact of hypoid gear set.
    NOTE:

    Used together with WRENCH (499787700). 

  • Used for removing and installing the drive pinion lock nut.
    NOTE:

    Used together with WRENCH (499787700). 

  • Used for measuring the initial load on the taper roller bearing.
G13591929Courtesy of SUBARU OF AMERICA, INC.
 18675AA000 DIFFERENTIAL SIDE OIL SEAL INSTALLER Used for installing the differential side retainer oil seal.
G07913245Courtesy of SUBARU OF AMERICA, INC.
 18681AA000 PRESSURE GAUGE ADAPTER
  • Used for measuring the secondary pressure.
    NOTE:
    • Use the genuine O-ring (part No. 806911080) for installation. 
    • Used together with OIL PRESSURE ADAPTER SET (498897700) and OIL PRESSURE GAUGE ASSY (18801AA000). 
  • Used for measuring the transfer clutch pressure.
    NOTE:
    • Use the genuine O-ring (part No. 806911080) for installation. 
    • Used together with OIL PRESSURE GAUGE ASSY (498575400), ADAPTER HOSE A (34099AC010) and ADAPTER HOSE B (34099AC020). 
G13621849Courtesy of SUBARU OF AMERICA, INC.
 18681AA010 PRESSURE GAUGE ADAPTER Used for measuring line pressure.
NOTE:
  • Use the genuine O-ring (part No. 806916050) for installation. 
  • Used together with OIL PRESSURE ADAPTER SET (498897700) and OIL PRESSURE GAUGE ASSY (18801AA000). 
G13591933Courtesy of SUBARU OF AMERICA, INC.
 18760AA000 CLAW
  • Used for removing the ball bearing of the converter case cover.
    NOTE:

    Used together with PULLER ASSY (398527700). 

  • Used for removing the roller bearing of the secondary pulley side in the transmission case.
    NOTE:

    Used together with PULLER ASSY (398527700). 
G13591935Courtesy of SUBARU OF AMERICA, INC.
 18762AA001 COMPRESSOR SPECIAL TOOL
  • Used for removing and installing the transfer clutch piston.
  • Used for removing and installing the reverse brake piston.
  • Used for removing and installing the forward clutch piston.
  • COMPRESSOR SPECIAL TOOL (18762AA000) can also be used.
G13591937Courtesy of SUBARU OF AMERICA, INC.
 18763AA000 COMPRESSOR SHAFT Used for measuring and adjusting the backlash of the hypoid gear set.
G13603085Courtesy of SUBARU OF AMERICA, INC.
 18767AA000 BEARING REMOVER Used for removing the bearing retainer.
NOTE:

Used together with INSTALLER (20099AE020). 
G13199952Courtesy of SUBARU OF AMERICA, INC.
 18769AA020 EXPANDER PULLEY Used for removing and installing the secondary pulley.
G07913243Courtesy of SUBARU OF AMERICA, INC.
 18801AA000 OIL PRESSURE GAUGE ASSY
  • Used for measuring the secondary pressure.
    NOTE:

    Used together with OIL PRESSURE ADAPTER SET (498897700) and PRESSURE GAUGE ADAPTER (18681AA000). 

  • Used for measuring line pressure.
    NOTE:

    Used together with OIL PRESSURE ADAPTER SET (498897700) and PRESSURE GAUGE ADAPTER (18681AA010). 
G09481347Courtesy of SUBARU OF AMERICA, INC.
 20099AE020 INSTALLER
  • Used for installing the drive sprocket ball bearing.
  • Used for removing the bearing retainer.
    NOTE:

    Used together with BEARING REMOVER (18767AA000). 

  • Used for installing the ball bearing of the reduction driven gear side in the transmission case.
    NOTE:

    Used together with INSTALLER (398177700). 

  • Used for installing the roller bearing of the secondary pulley side in the transmission case.
    NOTE:

    Used together with PRESS SNAP RING (499755602). 

  • Used for installing the roller bearing of the primary pulley side in the transmission case.
  • Used for installing drive pinion retainer oil seal.
  • Used for installing the ball bearing of the converter case cover.
G13621857Courtesy of SUBARU OF AMERICA, INC.
 34099AC010 ADAPTER HOSE A Used for measuring the transfer clutch pressure.
NOTE:

Used together with OIL PRESSURE GAUGE ASSY (498575400), PRESSURE GAUGE ADAPTER (18681AA000) and ADAPTER HOSE B (34099AC020). 
G13621858Courtesy of SUBARU OF AMERICA, INC.
 34099AC020 ADAPTER HOSE B Used for measuring the transfer clutch pressure.
NOTE:
  • Use the genuine union screw (part No. 801914010) and gasket (part No. 803914060) for installation. 
  • Used together with OIL PRESSURE GAUGE ASSY (498575400), PRESSURE GAUGE ADAPTER (18681AA000) and ADAPTER HOSE A (34099AC010). 
G13591943Courtesy of SUBARU OF AMERICA, INC.
 38415AA070 AXLE SHAFT Used for measuring the hypoid gear set backlash and adjusting the thrust washer.
NOTE:

This is the SUBARU genuine part. 
G13591944Courtesy of SUBARU OF AMERICA, INC.
 41099AA012 ENGINE SUPPORT BRACKET Used for removing and installing transmission body.
NOTE:

Used together with ENGINE SUPPORT (41099AA020). 
G13603094Courtesy of SUBARU OF AMERICA, INC.
 41099AA020 ENGINE SUPPORT Used for removing and installing transmission body.
NOTE:

Used together with ENGINE SUPPORT BRACKET (41099AA012). 
G13591946Courtesy of SUBARU OF AMERICA, INC.
 73099SG000 SPECIAL TOOL CONDENSER Used for removing and installing the test plug (transfer clutch pressure).
NOTE:

Used together with SOCKET (18270AA040). 
G10289719Courtesy of SUBARU OF AMERICA, INC.
 - SUBARU SELECT MONITOR 4 Used for setting of each function and troubleshooting for electrical system.
NOTE:
  • For detailed operation procedures, refer to "Help" of application. 
  • Used together with interface for Subaru Select Monitor (such as DST-i and DST-010). 
scientia non olet · About LEMON Manuals