General Diagnostic Table: Inspection
Read the DTC using Subaru Select Monitor. Ref. to BODY CONTROL (DIAGNOSTICS)>DIAGNOSTIC TROUBLE CODE (DTC) . Or check the following data under the data monitor display screen. Ref. to BODY CONTROL (DIAGNOSTICS)>DATA MONITOR .
| Item | Operation | Judgment standards | Note | |
|---|---|---|---|---|
| YES | NO | |||
| Diagnostic trouble code | DTC is not displayed when inspecting all DTCs. | DTC is not displayed. | Perform the diagnosis for the displayed DTCs. | - |
| Clearance light (Low beam) (High beam) | Clearance light and low/high beams illuminate normally when the switch is operated. Indicator in the meter illuminates at the same time. | System is normal. | Check the lighting system, combination meter system and LAN system. | - |
| Auto light | When the area around the light control sensor is darkened after the ignition switch and the lighting switch (AUTO) are turned to ON, the clearance light and the low beam illuminate after 1 second. Indicator in the combination meter illuminates at the same time. | System is normal. | Check the lighting system, combination meter system and LAN system. | - |
| When the ignition switch and the lighting switch (AUTO) are turned to ON after the area around the light control sensor is darkened, the clearance light and the low beam illuminate immediately. Indicator in the combination meter illuminates at the same time. | - | |||
| Rear defogger | Rear defogger operates when the switch is operated. The indicator illuminates at the same time. | System is normal. | Check the rear window defogger system and A/C system. | - |
| Shift lock | The select lever can be moved from the P range to other ranges only when the brake pedal is depressed with IG ON. | System is normal. | Check the body control system. | - |
| Door lock | The doors lock/unlock when the door switch is operated. The trunk opens when the trunk opener switch is operated. | System is normal. | Check the security & lock and body control system. | If customizing "Sedan/Wagon Setting" is different, the trunk does not open. |
| Keyless access with push button start system | The lock locks/unlocks when the access key is operated. With the access key held, the touch sensor (lock) operation locks/touch sensor (unlock) operation unlocks. Trunk unlocks when the trunk unlock button is operated. |
System is normal. | Check the keyless access with push button start system and the body control system. | - |
| Answer back | Answer-back operates when the keyless access with push button start system locks/unlocks. | System is normal. | Check the keyless access with push button start system and the LAN system. | - |
| Map light | Turns ON/OFF according to the door open/close operation, the lock/unlock operation with the keyless access with push button start system, and the ignition operation. | System is normal. | Check the spot map light, security & lock, keyless access with push button start system, and LAN system. | The map light blinks when "Factory" mode is selected. |
| Turn signal & hazard | Each turn signal light illuminates, when the turn signal switch is turned ON. | The hazard light and indicator in the combination meter blink, when the hazard switch is turned ON. | System is normal. Check the lighting system (turn signal light and hazard light system). | - |
| Vehicle security | Security monitoring/security canceling can be performed by operating the keyless access with push button start system. | System is normal. | Check the security & lock, keyless access with push button start system, and LAN system. | - |
| Welcome lighting (enter) | After turning the lighting switch (AUTO) to ON, use the access key to unlock. At this time, the clearance light illuminates for the preset time. And, use the access key to lock. At this time, the clearance light goes out. |
System is normal. | Check the lighting system (auto light) and keyless access with push button start system. | Operates when user customization item "Illumination Sensor Setting" in body integrated unit is set to ON and "Welcome lighting (enter)" is set to other than OFF. |
| Welcome lighting (exit) | The clearance light continues to illuminate when the ignition switch is OFF while the auto light function is operating. Use the access key to lock two consecutive times. At this time, the clearance light goes out. | System is normal. | Check the lighting system (auto light) and keyless access with push button start system. | Operates when user customization item "Illumination Sensor Setting" in body integrated unit is set to ON and "Welcome lighting (exit)" is set to other than OFF. |