LEMON Manuals: Even more car manuals for everyone
Home >> Subaru >> 2022 >> BRZ Limited, Automatic Trans >> Repair and Diagnosis >> Accessories & Equipment >> Collision/Avoidance >> Eyesight System >> Stereo Camera >> Installation

Stereo Camera: Installation

CAUTION:
  • Do not remove the protective cover until just before installing the cover assembly stereo camera. Using the bolt and nut, install the stereo camera with the protective cover attached, connect the connectors, and then remove the protective cover.
  • Do not change the installation position of the stereo camera or do not modify the surrounding structure.
  • Remove the protective cover, install the cover assembly stereo camera, and then perform adjustment and inspection of the stereo camera. Ref. to EYESIGHT>CAMERA ADJUSTMENT, INSPECTION .
  • When installing the cover assembly stereo camera, cover with dust-free paper such as copy paper to avoid interference with the lens filter section, and attach the paper using tape while being careful not to let the adhesive surface contact the glass surface. Be sure to remove the paper after the procedure.

    Also, do not put your hand on the polyurethane section of the windshield glass contact surface. Doing so may cause the polyurethane section to be removed, which may interfere with the normal operation if it hangs down in front of the lens filter section.

  • Because the stereo camera is incompatible, be sure to check the part number before installation.
  1. Install the plate (adjuster).
    NOTE: Align the positioning pins of plate (adjuster) to the positioning holes of front rail.

    Tightening torque: 

    5.5 ±1 N.m (0.56±0.1 kgf-m, 4.1±0.7 ft-lb)

  2. Install the stereo camera, and connect the connector.
    CAUTION:
    • Do not hold at the left and right cameras.
    • Do not touch the lens filter on the stereo camera. If touched, replace the stereo camera.
    • Do not apply any impact to the stereo camera. Even the slightest shock will deviate the optical axis of the camera, resulting in the loss of normal operation of the camera.
    NOTE: Align the positioning holes of stereo camera with the positioning pins of plate (adjuster).

    Tightening torque: 

    5.5±1 N.m (0.56±0.1 kgf-m, 4.1±0.7 ft-lb)

  3. Install the cover assembly stereo camera.
    CAUTION:
    • Avoid hitting the cover assembly stereo camera. Hitting may apply impact to the stereo camera.
    • Take care so that the harness or other part does not interfere with the stereo camera or does not get caught.
    • Do not allow the cover assembly stereo camera to come in contact with the stereo camera. Install the cover assembly stereo camera precisely so that it will not block the visibility of the camera.
    1. Connect each connector.
    2. Push the section (a) of the cover assembly stereo camera upward, and engage the front hook to the plate (adjuster).
    3. Push the section (b) of the cover assembly stereo camera upward, and engage the clips to install the cover assembly stereo camera.

      Tightening torque: 

      5.5 ±1 N.m (0.56±0.1 kgf-m, 4.1±0.7 ft-lb)

      G16527425Courtesy of SUBARU OF AMERICA, INC.
    4. Install cap.
  4. Connect the ground terminal to battery sensor. Ref. to REPAIR CONTENTS>NOTE>BATTERY .
  5. Remove the paper affixed on the cover assembly stereo camera.
  6. Visually check from the vehicle front that the lens portion of stereo camera is set in the center of the cover assembly stereo camera opening.
    NOTE: If the lens portion of stereo camera is not centered and the gap to the cover assembly stereo camera is large, check the installation condition of cover assembly stereo camera.
    G13079082Courtesy of SUBARU OF AMERICA, INC.
  7. Perform the adjustment or inspection of the stereo camera. Ref. to EYESIGHT>CAMERA ADJUSTMENT, INSPECTION .
scientia non olet · About LEMON Manuals