52 Ω Or Less

Wiring diagram:

CAN communication system Refer to WIRING SYSTEM>CAN COMMUNICATION SYSTEM>WIRING DIAGRAM .

Courtesy of SUBARU OF AMERICA, INC.

Courtesy of SUBARU OF AMERICA, INC.

NOTE: When the bus line is measured, combined resistance of end resistance (120 Ω) in ECM and end resistance (120 Ω) in VDC CONTROL MODULE can be measured. The combined resistance is supposed to be more than 52 Ω and less than 62 Ω with the stabilizing circuit included. When the measured resistance value is 52 Ω or less, main wiring harness or related lines may be shorted, or combined resistance may have changed because resistance other than end resistance is created on the circuit.

CHECK BETWEEN RELATED LINES AND MAIN WIRING HARNESS.
1. Turn the ignition switch to OFF.
2. Disconnect the steering angle sensor connector.
3. Using the tester, measure the resistance between terminals.
  Connector & terminal
  
  (B231) No. 2 - (B231) No. 3:
Is the resistance less than 10 Ω?

Yes: Go to 2.

No: Go to 4.
CHECK MAIN WIRING HARNESS AND RELATED LINES.
With a tester connected, disconnect control module connectors in order.

NOTE: Disconnect the body integrated unit at the end.

Connector & terminal

(B231) No. 2 - (B231) No. 3:

Is there any control module whose condition has changed from short state?

Yes: Replace the control module whose resistance has changed. When the value changed at disconnecting the body integrated unit,

Go to 3.

No: Repair or replace the short circuit of the harness between body integrated unit and ECM.
CHECK BETWEEN MAIN WIRING HARNESSES.
Using the tester, measure the resistance between terminals.

Connector & terminal

(B281) No. 20 - (B281) No. 28:

Is the resistance less than 10 Ω?

Yes: Repair or replace the short circuit of the harness between VDC CONTROL MODULE and body integrated unit.

No: Replace the body integrated unit. Refer to SECURITY AND LOCKS>BODY INTEGRATED UNIT .
CHECK CONTROL MODULE.
1. Disconnect ECM and VDC CONTROL MODULE connectors.
2. Using a tester, measure the resistance between control module terminals.
  Connector & terminal
  
  Engine type: FA
  
  (B134) No. 9 - No. 10:
  
  (B310) No. 10 - No. 11 (without EyeSight):
  
  (B310) No. 42 - No. 43 (with EyeSight):
  
  Engine type: EJ
  
  (B136) No. 17 - No. 28:
  
  (B310) No. 10 - No. 11 (without EyeSight):
  
  (B310) No. 42 - No. 43 (with EyeSight):
Is the resistance 114 - 126 Ω?

Yes: Go to 5.

No: Replace the control module whose end resistance value is out of the specified range.
CHECK CONTROL MODULE.
1. Disconnect the connector of body integrated unit.
2. Using a tester, measure the resistance between control module terminals.
  Connector & terminal
  
  (B281) No. 28 - (i84) No. 27:
  
  (B281) No. 20 - (i84) No. 35:
Is the resistance 2850 - 3150 Ω?

Yes: Go to 6.

No: Replace the body integrated unit. Refer to SECURITY AND LOCKS>BODY INTEGRATED UNIT .
CHECK CONTROL MODULE.
Using a tester, measure the resistance between control module terminals.

Connector & terminal

(B281) No. 28 - (i84) No. 35:

(B281) No. 20 - (i84) No. 27:

Is the resistance less than 1 Ω?

Yes: Go to 7.

No: Replace the body integrated unit. Refer to SECURITY AND LOCKS>BODY INTEGRATED UNIT .
CHECK CONTROL MODULE.
1. Disconnect the combination meter connector.
2. Using a tester, measure the resistance between control module terminals.
  Connector & terminal
  
  (i10) No. 32 - (i10) No. 33:
Is the resistance 2850 - 3150 Ω?

Yes: Go to 8.

No: Replace the combination meter. Refer to INSTRUMENTATION/DRIVER INFO>COMBINATION METER .
CHECK CONTROL MODULE (ONLY FOR MODELS WITH HIGH GRADE MFD).
1. Disconnect the MFD connector.
2. Using a tester, measure the resistance between control module terminals.
  Connector & terminal
  
  (i122) No. 19 - (i122) No. 20:
Is the resistance 2850 - 3150 Ω?

Yes: Go to 9.

No: Replace the MFD. Refer to INSTRUMENTATION/DRIVER INFO>MULTI-FUNCTION DISPLAY (MFD) .
CHECK HARNESS.
Using the tester, check the short circuit of each harness.

Connector & terminal

(B281) No. 28 - (B281) No. 20:

Is the resistance 1 MΩ or more?

Yes: Go to 11.

No: Go to 10.
CHECK CONTROL MODULE.
With a tester connected, disconnect control modules in order.

Connector & terminal

(B281) No. 28 - (B281) No. 20:

Are there any control modules whose resistance changed to 1 MΩ or more?

Yes: Replace the control module that has changed.

No: Repair or replace the harness part which has resistance component.
CHECK CONTROL MODULE.
With a tester connected, disconnect control modules in order.

Connector & terminal

(i84) No. 27 - (i84) No. 35:

Is there any control module whose resistance has changed to 1 MΩ or more?

Yes: Replace the control module that has changed.

No: Repair or replace the harness part which has resistance component.