LEMON Manuals: Even more car manuals for everyone
Home >> Subaru >> 2021 >> Outback Limited >> Repair and Diagnosis >> Body & Frame >> Seats >> Ventilation Seat (Diagnostics) >> Diagnostics With Phenomenon >> Inspection >> Seat Ventilation Does Not Operate According To The Last Memory

Seat Ventilation Does Not Operate According To The Last Memory

Trouble symptom: 

The ignition switch was turned from ON to OFF while the seat ventilation was in operation, and then was turned from OFF to ON again. However, the operation does not start in the operating condition the same as before turning the ignition switch OFF.

Trouble causes: 

Wiring diagram: 

Seat ventilation system Ref. to WIRING SYSTEM>SEAT VENTILATION SYSTEM>WIRING DIAGRAM .

G13630739Courtesy of SUBARU OF AMERICA, INC.
CAUTION: Before performing diagnosis, refer to "CAUTION" in "General Description". Ref. to VENTILATION SEAT (DIAGNOSTICS)>General Description>CAUTION .
  1. CHECK SEAT VENTILATION SWITCH DISPLAY  .
    1. Turn the ignition switch to ON.
    2. Touch the seat indicator on the center information display.
    3. Check if the seat ventilation switch is displayed under the seat heater switch.

      Is the seat ventilation switch displayed?

      Yes:  Go to  2 .

      No:  Ref. to VENTILATION SEAT (DIAGNOSTICS)>DIAGNOSTICS WITH PHENOMENON>INSPECTION>SEAT VENTILATION SWITCH IS NOT DISPLAYED .

  2. CHECK OPERATION CONDITION  .
    1. Turn the ignition switch to ON.
    2. Operate the seat ventilation.
    3. Turn the ignition switch to OFF with the seat ventilation ON.
    4. Turn the ignition switch to ON again.
      NOTE: When turning the ignition switch to ON using the telematics, do not turn the seat heater ON.

      Is the seat ventilation operation condition the same as before turning the ignition switch OFF?

      Yes:  The circuit has returned to a normal condition at this time. Reproduce the failure, and then perform the diagnosis again.

      No:  Go to  3 .

  3. CHECK DTC  .
    1. Turn the ignition switch to ON.
    2. Read the following DTCs using Subaru Select Monitor. Ref. to Ventilation Seat (Diagnostics)>Diagnostic Trouble Code (DTC) . Ref. to BODY CONTROL (DIAGNOSTICS)>DIAGNOSTIC TROUBLE CODE (DTC) . Ref. to AIR CONDITIONER (DIAGNOSTICS)>DIAGNOSTIC TROUBLE CODE (DTC) . Ref. to COCKPIT CONTROL (DIAGNOSTICS)>DIAGNOSTIC TROUBLE CODE (DTC) .
      • Ventilation Seat
      • Body Control
      • Air Conditioner
      • Cockpit Control

      Are any DTCs displayed?

      Yes:  Perform the diagnosis for the displayed DTCs. Ref. to Ventilation Seat (Diagnostics)>Diagnostic Trouble Code (DTC) . Ref. to BODY CONTROL (DIAGNOSTICS)>DIAGNOSTIC TROUBLE CODE (DTC) . Ref. to AIR CONDITIONER (DIAGNOSTICS)>DIAGNOSTIC TROUBLE CODE (DTC) . Ref. to COCKPIT CONTROL (DIAGNOSTICS)>DIAGNOSTIC TROUBLE CODE (DTC) .

      No:  Go to  4 .

  4. CHECK CONNECTOR  .
    1. Turn the ignition switch to OFF.
    2. Check connecting condition of the seat ventilation control module connector (St41), seat connectors (L57) (R57), coupling connectors (B43) (L51) (R51) (St21) (St22), and blower connectors (St71) (St72).

      Is the check result OK?

      Yes:  Go to  5 .

      No:  Repair the connector.

  5. CHECK CONNECTOR  .

    Check malfunctions (terminal bends, etc.) of the driver's side seat connector (L57) and passenger's side seat connector (R57).

    Is the check result OK?

    Yes:  Go to  6 .

    No:  Repair the connector.

  6. CHECK CENTER INFORMATION DISPLAY  .
    1. Start the engine.
    2. Touch the passenger's side seat ventilation switch on the center information display, and check if the display for passenger's side seat ventilation operation mode changes.

      Does the display change?

      Yes:  Go to  7 .

      No:  Ref. to VENTILATION SEAT (DIAGNOSTICS)>DIAGNOSTICS WITH PHENOMENON>INSPECTION>DISPLAY DOES NOT CHANGE ALONG WITH SEAT VENTILATION SWITCH OPERATION .

  7. CHECK OPERATION MODE  .
    1. Touch the passenger's side seat ventilation switch on the center information display.
    2. Check if the passenger's side ventilation operation mode changes.

      Does the operation mode change?

      Yes:  Go to  8 .

      No:  Ref. to VENTILATION SEAT (DIAGNOSTICS)>DIAGNOSTICS WITH PHENOMENON>INSPECTION>PASSENGER'S SIDE SEAT VENTILATION LEVEL DOES NOT CHANGE (DISPLAY CHANGES, BUT OPERATION DOES NOT CHANGE) .

  8. CHECK SEAT VENTILATION  .
    1. Turn the seat ventilation ON.
    2. Check if both blowers for backrest and cushion on the passenger's side are operating.

      Are both the backrest side and cushion side operating?

      Yes:  Go to  9 .

      No:  Ref. to VENTILATION SEAT (DIAGNOSTICS)>DIAGNOSTICS WITH PHENOMENON>INSPECTION>BLOWER ON ONE SIDE (BACKREST SIDE OR CUSHION SIDE) DOES NOT OPERATE .

  9. CHECK HARNESS (OPEN CIRCUIT)  .
    1. Turn the ignition switch to OFF.
    2. Disconnect the passenger's side seat connector (St1) and seat ventilation control module connector (St41).
    3. Using the tester, measure the resistance between terminals.

      Connector and terminal 

      (St41) No. 5 - (St1) No. 11:

      (St41) No. 14 - (St1) No. 13:

      Is the resistance less than 5 Ω?

      Yes:  Go to  10 .

      No:  Repair or replace the open circuit of harness.

  10. CHECK HARNESS (OPEN CIRCUIT)  .
    1. Disconnect the driver's side seat connector (L57) and passenger's side seat connector (R57).
    2. Using the tester, measure the resistance between terminals.

      Connector and terminal 

      (L57) No. 11 - (R57) No. 11:

      (L57) No. 13 - (R57) No. 13:

      Is the resistance less than 5 Ω?

      Yes:  Go to  11 .

      No:  Repair or replace the open circuit of harness.

  11. CHECK CENTER INFORMATION DISPLAY  .
    1. Connect all connectors.
    2. Turn the ignition switch to ON.
    3. Start the engine.
    4. Touch the driver's side seat ventilation switch on the center information display, and check if the display for driver's side ventilation operation mode changes.

      Does the display change?

      Yes:  Go to  12 .

      No:  Ref. to VENTILATION SEAT (DIAGNOSTICS)>DIAGNOSTICS WITH PHENOMENON>INSPECTION>DISPLAY DOES NOT CHANGE ALONG WITH SEAT VENTILATION SWITCH OPERATION .

  12. CHECK OPERATION MODE  .
    1. Touch the driver's side seat ventilation switch on the center information display.
    2. Check if the driver's side seat ventilation operation mode changes.

      Does the operation mode change?

      Yes:  Go to  13 .

      No:  Ref. to VENTILATION SEAT (DIAGNOSTICS)>DIAGNOSTICS WITH PHENOMENON>INSPECTION>DRIVER'S SIDE SEAT VENTILATION LEVEL DOES NOT CHANGE (DISPLAY CHANGES, BUT OPERATION DOES NOT CHANGE) .

  13. CHECK SEAT VENTILATION  .
    1. Turn the seat ventilation ON.
    2. Check if both blowers for backrest and cushion on the driver's side are operating.

      Are both the backrest side and cushion side operating?

      Yes:  Even if DTC is displayed, the circuit has returned to a normal condition at this time.

      Reproduce the failure, and then perform the diagnosis again.

      NOTE: In this case, temporary poor contact of connector, temporary open or short circuit of harness may be the cause.

      No:  Ref. to VENTILATION SEAT (DIAGNOSTICS)>DIAGNOSTICS WITH PHENOMENON>INSPECTION>BLOWER ON ONE SIDE (BACKREST SIDE OR CUSHION SIDE) DOES NOT OPERATE .

scientia non olet · About LEMON Manuals