LEMON Manuals: Even more car manuals for everyone
Home >> Subaru >> 2021 >> Crosstrek Hybrid >> Repair and Diagnosis >> External Pages >> Different variant/trim >> Section 3 (HVAC System (Diagnostics) (Except HEV)) >> Diagnostics With Phenomenon >> Inspection >> Warm Air Not Emitted

Warm Air Not Emitted

WARNING: This page is about a different variant/trim than selected.

Trouble symptom: 

Warm air not emitted.

Trouble causes: 

CAUTION: Before performing diagnosis, refer to "CAUTION" in "General Description". Ref. to AIR CONDITIONER (DIAGNOSTICS) (EXCEPT FOR HEV)> GENERAL DESCRIPTION> CAUTION .
  1. CHECK MAX HOT  .

    Set the A/C control panel switch or dial as follows.

    • Temperature control dial: MAX HOT
    • FRESH/RECIRC switch: FRESH
    • Mode switch or mode dial: HEAT
    • A/C switch: OFF

    Does it fail to blow the hot air?

    Yes:  Go to  2.

    No:  Go to  4.

  2. CHECK AIRFLOW CAPACITY  .

    Check the airflow capacity. Ref. to AIR CONDITIONER (DIAGNOSTICS) (EXCEPT FOR HEV)>DIAGNOSTICS WITH PHENOMENON>INSPECTION>AIR DOES NOT COME OUT. OR AIRFLOW CAPACITY IS INSUFFICIENT (BLOWER MOTOR DOES NOT ROTATE) .

    Is the check result OK?

    Yes:  Go to  3.

    No:  Perform repair according to inspection procedure.

  3. CHECK ENGINE COOLANT  .

    Check engine coolant amount.

    Is the engine coolant level within the specification?

    Yes:  Go to  4.

    No:  Fill engine coolant. If there is coolant leakage, repair the leaks according to Engine Cooling System Trouble in General Ref. to COOLING (H4DO (EXCEPT FOR HEV))>ENGINE COOLING SYSTEM TROUBLE IN GENERAL .

  4. CHECK A/C CONTROL PANEL  .
    1. Turn the ignition switch to ON.
    2. Turn the temperature control dials (driver's side) and (passenger's side) to MAX COOL.
    3. Using the Subaru Select Monitor, check the following items in the [Data Monitor] of [Air Conditioner]. Ref. to AIR CONDITIONER (DIAGNOSTICS) (EXCEPT FOR HEV)> DATA MONITOR .
      • Heater Control Panel Setting Value (Driver's)
      • Heater Control Panel Setting Value (Passenger's)

      Do [Heater Control Panel Setting Value (Driver's)] and [Heater Control Panel Setting Value (Passenger's)] indicate "59"*1?

      (*1: For the 72°F center specification. 17.5 for the 25°C center specification.)

      Yes:  Go to  5.

      No:  Replace the A/C control panel. Ref. to AIR CONDITIONER (EXCEPT FOR HEV)> CONTROL PANEL .

  5. CHECK A/C CONTROL PANEL  .
    1. Turn the temperature control dials (driver's side) and (passenger's side) to MAX HOT.
    2. Using the Subaru Select Monitor, check the following items in the [Data Monitor] of [Air Conditioner]. Ref. to AIR CONDITIONER (DIAGNOSTICS) (EXCEPT FOR HEV)> DATA MONITOR .
      • Heater Control Panel Setting Value (Driver's)
      • Heater Control Panel Setting Value (Passenger's)

      Do [Heater Control Panel Setting Value (Driver's)] and [Heater Control Panel Setting Value (Passenger's)] indicate "86"*2?

      (*2: For the 72°F center specification. 32.5 for the 25°C center specification.)

      Yes:  Go to  6.

      No:  Replace the A/C control panel. Ref. to AIR CONDITIONER (EXCEPT FOR HEV)> CONTROL PANEL .

  6. CHECK DTC  .
    1. Turn the temperature control dial at MAX COOL and leave for 16 seconds or more. (For vehicles with left/right independent air conditioner, perform setting on both sides.)
    2. Read the DTC of [Air Conditioner] using the Subaru Select Monitor Ref. to AIR CONDITIONER (DIAGNOSTICS) (EXCEPT FOR HEV)> DIAGNOSTIC TROUBLE CODE (DTC) .

      Is DTC B1440, B1442, B1446, B1436, B1437 or B1441 displayed? (Current malfunction)

      Yes:  Perform the diagnosis for the displayed DTC B1440, B1442, B1446, B1436, B1437 or B1441.

      No:  Go to  7.

  7. CHECK DTC  .
    1. Turn the temperature control dial at MAX HOT and leave for 16 seconds or more. (For vehicles with left/right independent air conditioner, perform setting on both sides.)
    2. Read the DTC of [Air Conditioner] using the Subaru Select Monitor. Ref. to AIR CONDITIONER (DIAGNOSTICS) (EXCEPT FOR HEV)> DIAGNOSTIC TROUBLE CODE (DTC) .

      Is DTC B1440, B1442, B1446, B1436, B1437 or B1441 displayed? (Current malfunction)

      Yes:  Perform the diagnosis for the displayed DTC B1440, B1442, B1446, B1436, B1437 or B1441.

      No:  Go to  8.

  8. CHECK INTAKE DOOR ACTUATOR  .

    Visually check the intake door actuator operation.

    Is the check result OK?

    Yes:  Go to  9.

    No:  Check the intake door actuator. Ref. to AIR CONDITIONER (DIAGNOSTICS) (EXCEPT FOR HEV)>DIAGNOSTICS WITH PHENOMENON>INSPECTION>UNABLE TO SWITCH SUCTION VENTS .

  9. CHECK EVAPORATOR SENSOR UNIT  .

    Perform the inspection of evaporator sensor unit Ref. to AIR CONDITIONER (EXCEPT FOR HEV)> EVAPORATOR SENSOR .

    Is the check result OK?

    Yes:  Go to  10.

    No:  Replace the evaporator sensor. Ref. to AIR CONDITIONER (EXCEPT FOR HEV)> EVAPORATOR SENSOR .

  10. CHECK IN-VEHICLE SENSOR OR TEMPERATURE AND HUMIDITY SENSOR UNIT  .

    Check the in-vehicle sensor (without humidity sensor) or temperature and humidity sensor (with humidity sensor). Ref. to AIR CONDITIONER (EXCEPT FOR HEV)>IN-VEHICLE SENSOR AUTO A/C MODEL . Ref. to AIR CONDITIONER (EXCEPT FOR HEV)> TEMPERATURE AND HUMIDITY SENSOR .

    Is the check result OK?

    Yes:  Go to  11.

    No:  Replace the in-vehicle sensor (without humidity sensor) or temperature and humidity sensor (with humidity sensor) Ref. to AIR CONDITIONER (EXCEPT FOR HEV)> IN-VEHICLE SENSOR (AUTO A/C MODEL) . Ref. to AIR CONDITIONER (EXCEPT FOR HEV)> TEMPERATURE AND HUMIDITY SENSOR .

  11. CHECK AMBIENT SENSOR UNIT  .

    Check the ambient sensor Ref. to AIR CONDITIONER (EXCEPT FOR HEV)> AMBIENT SENSOR .

    Is the check result OK?

    Yes:  Go to  12.

    No:  Replace the ambient sensor. Ref. to AIR CONDITIONER (EXCEPT FOR HEV)> AMBIENT SENSOR .

  12. CHECK SUNLOAD SENSOR UNIT  .

    Check the sunload sensor unit. Ref. to AIR CONDITIONER (EXCEPT FOR HEV)>SUNLOAD SENSOR (AUTO A/C MODEL) .

    Is the check result OK?

    Yes:  The circuit has returned to a normal condition at this time. Reproduce the failure, and then perform the diagnosis again.

    NOTE: In this case, temporary poor contact of connector, temporary open or short circuit of harness may be the cause.

    No:  Replace the sunload sensor. Ref. to AIR CONDITIONER (EXCEPT FOR HEV)>SUNLOAD SENSOR (AUTO A/C MODEL) .