SUBARU Special Tool

WARNING: This page is about a different variant/trim than selected.

ILLUSTRATION	TOOL NUMBER	DESCRIPTION	REMARKS
Courtesy of SUBARU OF AMERICA, INC.	398177700	INSTALLER	Used to install the rear drive shaft ball bearing. NOTE: Used together with EXTENSION DRIVE SHAFT (927130000). Used for installing the roller bearing of the secondary pulley side in the transmission case. NOTE: Used together with BUSHING 1-2 INSTALLER (499277100) and PRESS SNAP RING (28499TC010). Used for installing the taper roller bearing (front) outer race of drive pinion retainer. NOTE: Used together with PRESS SNAP RING (28499TC010). Used for installing the drive pinion retainer plug. NOTE: Used together with PRESS SNAP RING (499755602) and INSTALLER (899580100).
Courtesy of SUBARU OF AMERICA, INC.	398437700	OIL SEAL INSTALLER	Used for inspecting clutch clearance. NOTE: Used together with GAUGE (499575600).
Courtesy of SUBARU OF AMERICA, INC.	398497701	SEAT	Used for removing and installing the side bearing inner race. NOTE: Used together with PULLER ASSY (399703600) when removing. Used together with BUSHING 1-2 INSTALLER (499277100) when installing.
Courtesy of SUBARU OF AMERICA, INC.	398527700	PULLER ASSY	Used for removing the roller bearing of the secondary pulley side in the transmission case. NOTE: Used together with CLAW (18760AA000). Used for removing the taper roller bearing (front) outer race of drive pinion retainer, and taper roller bearing (rear) outer race. Used for removing the drive pinion retainer oil seal.
Courtesy of SUBARU OF AMERICA, INC.	398673600	COMPRESSOR	Used for removing and installing snap ring of forward clutch. NOTE: Used together with COMPRESSOR SPECIAL TOOL (18762AA010).
Courtesy of SUBARU OF AMERICA, INC.	399703600	PULLER ASSY	Used for removing the parking gear. Used for removing the side bearing inner race. NOTE: Used together with SEAT (398497701). PULLER ASSY (399703601) can also be used.
Courtesy of SUBARU OF AMERICA, INC.	498057300	INSTALLER	Used for installing the extension case oil seal.
Courtesy of SUBARU OF AMERICA, INC.	498077300	REMOVER	Used for removing the transfer drive gear ball bearing. NOTE: Used together with INSTALLER (18657AA000).
Courtesy of SUBARU OF AMERICA, INC.	498077400	REMOVER	Used for removing the ball bearing of transfer driven gear. NOTE: Used together with REMOVER (899864100).
Courtesy of SUBARU OF AMERICA, INC.	498077600	REMOVER	Used for removing the ball bearing of drive sprocket. NOTE: Used together with HOUSING BUSHING INSTALLER AND REMOVER (927720000).
Courtesy of SUBARU OF AMERICA, INC.	498255400	PLATE	Used for measuring the backlash of the hypoid gear set.
Courtesy of SUBARU OF AMERICA, INC.	498277200	STOPPER SET	Used for removing and installing transmission body.
Courtesy of SUBARU OF AMERICA, INC.	498497300	CRANKSHAFT STOPPER	Used for removing and installing the drive plate.
Courtesy of SUBARU OF AMERICA, INC.	498515500	REMOVER	Used for removing the taper roller bearing (front) inner race of the drive pinion and drive pinion shim.
Courtesy of SUBARU OF AMERICA, INC.	498575400	OIL PRESSURE GAUGE ASSY	Used for measuring the transfer clutch pressure. NOTE: Used together with PRESSURE GAUGE ADAPTER (18681AA000). Use the genuine O-ring (part No. 806908150) for installation.
Courtesy of SUBARU OF AMERICA, INC.	498937110	HOLDER	Used for removing and installing the drive pinion lock nut. NOTE: Used together with ADAPTER (499787500) and WRENCH (499787700). Used for adjusting hypoid gear set backlash. NOTE: Used together with WRENCH (499787700).
Courtesy of SUBARU OF AMERICA, INC.	499267300	STOPPER PIN	Used for adjusting the inhibitor switch.
Courtesy of SUBARU OF AMERICA, INC.	499277100	BUSHING 1-2 INSTALLER	Used for installing the roller bearing of the secondary pulley side in the transmission case. NOTE: Used together with INSTALLER (398177700) and PRESS SNAP RING (28499TC010). Used for installing the side bearing inner race. NOTE: Used together with SEAT (398497701).
Courtesy of SUBARU OF AMERICA, INC.	499755602	PRESS SNAP RING	Used for installing the drive pinion retainer plug. NOTE: Used together with INSTALLER (398177700) and INSTALLER (899580100).
Courtesy of SUBARU OF AMERICA, INC.	499575400	GAUGE	Used for adjusting the reduction drive gear shim. Used for adjusting the primary pulley shim. Used for adjusting the drive pinion washer. Used for adjusting the drive pinion shim.
Courtesy of SUBARU OF AMERICA, INC.	499575600	GAUGE	Used for adjusting the transfer driven gear shim. Used for adjusting the transfer drive gear shim. Used for adjusting the forward clutch washer. Used for inspecting clutch clearance. NOTE: Used together with OIL SEAL INSTALLER (398437700).
Courtesy of SUBARU OF AMERICA, INC.	499787500	ADAPTER	Used for removing and installing the drive pinion lock nut. NOTE: Used together with HOLDER (498937110) and WRENCH (499787700).
Courtesy of SUBARU OF AMERICA, INC.	499787700	WRENCH	Used for removing and installing the drive pinion lock nut. NOTE: Used together with HOLDER (498937110) and ADAPTER (499787500). Used for adjusting hypoid gear set backlash. NOTE: Used together with HOLDER (498937110).
Courtesy of SUBARU OF AMERICA, INC.	499987003	SOCKET WRENCH (35)	Used for removing and installing the lock nut of reduction driven gear. NOTE: Used together with PULLEY WRENCH PIN SET (18334AA000) and PULLEY WRENCH (18355AA000).
Courtesy of SUBARU OF AMERICA, INC.	899580100	INSTALLER	Used for installing the ball bearing of the transfer driven gear. Used for installing the taper roller bearing (front) inner race of drive pinion. NOTE: Used together with EXTENSION DRIVE SHAFT (927130000). Used for installing the drive pinion retainer plug. NOTE: Used together with INSTALLER (398177700) and PRESS SNAP RING (499755602).
Courtesy of SUBARU OF AMERICA, INC.	899864100	REMOVER	Used for removing the ball bearing of transfer driven gear. NOTE: Used together with REMOVER (498077400).
Courtesy of SUBARU OF AMERICA, INC.	899904100	STRAIGHT PIN REMOVER	Used for removing the spring pin of the differential case.
Courtesy of SUBARU OF AMERICA, INC.	927130000	EXTENSION DRIVE SHAFT	Used for installing the ball bearing of the transfer drive gear. NOTE: Used together with INSTALLER (398177700). Used for installing the transfer drive gear. Used for installing the parking gear. Used for installing the taper roller bearing (front) inner race of drive pinion. NOTE: Used together with INSTALLER (899580100).
Courtesy of SUBARU OF AMERICA, INC.	927720000	HOUSING BUSHING INSTALLER AND REMOVER	Used for installing the oil seal of the oil pump chain cover. NOTE: Use BUSHING SHAFT (927880000) and BASE TUBE LATERAL LINK (927890000). Used for removing the ball bearing of drive sprocket. NOTE: Use BUSHING SHAFT (927880000). Used together with REMOVER (498077600). Used for installing the drive pinion retainer oil seal. NOTE: Use BUSHING SHAFT (927880000).
Courtesy of SUBARU OF AMERICA, INC.	16047AA000	LOCK PLATE	Used for removing and installing the secondary pulley. NOTE: Used together with EXPANDER PULLEY (18769AA010). When using together with EXPANDER PULLEY (18769AA010), the EXPANDER PULLEY (18769AA030) is not necessary.
Courtesy of SUBARU OF AMERICA, INC.	18270KA020	SOCKET (E20)	Used for removing and installing the drive pinion retainer.
Courtesy of SUBARU OF AMERICA, INC.	18334AA000	PULLEY WRENCH PIN SET	Used for removing and installing the lock nut of reduction driven gear. NOTE: Used together with SOCKET WRENCH (35) (499987003) and PULLEY WRENCH (18355AA000).
Courtesy of SUBARU OF AMERICA, INC.	18355AA000	PULLEY WRENCH	Used for removing and installing the lock nut of reduction driven gear. NOTE: Used together with SOCKET WRENCH (35) (499987003) and PULLEY WRENCH PIN SET (18334AA000).
Courtesy of SUBARU OF AMERICA, INC.	18460AA040	CHECK BOARD	Used for measuring voltage and resistance of TCM terminals.
Courtesy of SUBARU OF AMERICA, INC.	18632AA000	STAND ASSY	Used for disassembling and assembling the transmission body.
Courtesy of SUBARU OF AMERICA, INC.	18657AA000	INSTALLER	Used for removing the transfer drive gear ball bearing. NOTE: Used together with REMOVER (498077300). Used for installing the transmission case oil seal.
Courtesy of SUBARU OF AMERICA, INC.	18658AA021	WRENCH COMPL RETAINER	Used for removing and installing the differential side retainer.
Courtesy of SUBARU OF AMERICA, INC.	18681AA000	PRESSURE GAUGE ADAPTER	Used for measuring the transfer clutch pressure. NOTE: Used together with OIL PRESSURE GAUGE ASSY (498575400). Use the genuine O-ring (part No. 806911080) for installation.
Courtesy of SUBARU OF AMERICA, INC.	18723AA000	REMOVER	Used for removing the ball bearing of the rear drive shaft. NOTE: Used together with BEARING REMOVER (18767AA010).
Courtesy of SUBARU OF AMERICA, INC.	18760AA000	CLAW	Used for removing the roller bearing of the secondary pulley side in the transmission case. NOTE: Used together with PULLER ASSY (398527700).
Courtesy of SUBARU OF AMERICA, INC.	18761AA010	SHEET SPECIAL TOOL	Used for removing and installing valve cover. NOTE: It is included in the control valve body for repairs.
Courtesy of SUBARU OF AMERICA, INC.	18762AA001	COMPRESSOR SPECIAL TOOL	Used for removing and installing the transfer clutch piston. Used for removing and installing the reverse brake piston. COMPRESSOR SPECIAL TOOL (18762AA000) can also be used.
Courtesy of SUBARU OF AMERICA, INC.	18762AA010	COMPRESSOR SPECIAL TOOL	Used for removing and installing snap ring of forward clutch. NOTE: Used together with COMPRESSOR (398673600).
Courtesy of SUBARU OF AMERICA, INC.	18763AA000	COMPRESSOR SHAFT	Used for adjusting hypoid gear set backlash.
Courtesy of SUBARU OF AMERICA, INC.	18767AA000	BEARING REMOVER	Used for removing the transfer drive gear.
Courtesy of SUBARU OF AMERICA, INC.	18767AA010	BEARING REMOVER	Used for removing the ball bearing of the rear drive shaft. NOTE: Used together with REMOVER (18723AA000).
Courtesy of SUBARU OF AMERICA, INC.	18769AA010	EXPANDER PULLEY	Used for removing and installing the secondary pulley. NOTE: Used together with LOCK PLATE (16047AA000). When using together with LOCK PLATE (16047AA000), the EXPANDER PULLEY (18769AA030) is not necessary.
Courtesy of SUBARU OF AMERICA, INC.	18769AA030	EXPANDER PULLEY	Used for removing and installing the secondary pulley. NOTE: When using EXPANDER PULLEY (18769AA030), EXPANDER PULLEY (18769AA010) and LOCK PLATE (16047AA000) are not necessary.
Courtesy of SUBARU OF AMERICA, INC.	18801AA000	OIL PRESSURE GAUGE ASSY	Used for measuring the line pressure and secondary pressure. NOTE: Use the genuine O-ring (part No. 806908150) for installation.
Courtesy of SUBARU OF AMERICA, INC.	20099AE020	INSTALLER	Used for installing the drive sprocket ball bearing. Used for installing the taper roller bearing (rear) outer race of drive pinion retainer.
Courtesy of SUBARU OF AMERICA, INC.	28499TC010	PRESS SNAP RING	Used for installing the roller bearing of the secondary pulley side in the transmission case. NOTE: Used together with INSTALLER (398177700) and BUSHING 1-2 INSTALLER (499277100). Used for installing the taper roller bearing (front) outer race of drive pinion retainer. NOTE: Used together with INSTALLER (398177700).
Courtesy of SUBARU OF AMERICA, INC.	38415AA070	Axle shaft	Used for measuring the hypoid gear set backlash and adjusting the thrust washer. NOTE: This is the SUBARU genuine part.
Courtesy of SUBARU OF AMERICA, INC.	41099AA012	ENGINE SUPPORT BRACKET	Used for removing and installing transmission body. NOTE: Used together with ENGINE SUPPORT (41099AA020).
Courtesy of SUBARU OF AMERICA, INC.	41099AA020	ENGINE SUPPORT	Used for removing and installing transmission body. NOTE: Used together with ENGINE SUPPORT BRACKET (41099AA012).
Courtesy of SUBARU OF AMERICA, INC.	-	SUBARU SELECT MONITOR 4	Used for setting of each function and troubleshooting for electrical system. NOTE: For detailed operation procedures, refer to "Help" of application.