LEMON Manuals: Even more car manuals for everyone
Home >> Subaru >> 2020 >> Crosstrek Base, Automatic CVT Trans >> Repair and Diagnosis >> External Pages >> Different variant/trim >> Section 8 (Manual Transaxle & Differential (6MT)) >> General Description >> Preparation Tool >> Special Tool

Special Tool

WARNING: This page is about a different variant/trim than selected.
ILLUSTRATION TOOL NUMBER DESCRIPTION REMARKS
G13602196Courtesy of SUBARU OF AMERICA, INC.
 899524100 PULLER SET Used for removing the front differential taper roller bearing.
  1. Puller
  2. Cap
G05002914Courtesy of SUBARU OF AMERICA, INC.
 399780104 WEIGHT Used for adjusting preload on the front differential taper roller bearing.
G05002433Courtesy of SUBARU OF AMERICA, INC.
 498077000 REMOVER
  • Used for removing the roller bearing and washer of the drive pinion shaft assembly.
  • Used for removing the transfer driven gear taper roller bearing.
G05002454Courtesy of SUBARU OF AMERICA, INC.
 498077600 REMOVER Used for removing the center differential ball bearing.
G07914986Courtesy of SUBARU OF AMERICA, INC.
 18667AA020 HOLDER
  • Used for removing and installing the drive pinion shaft assembly lock nut.
  • Used for measuring the backlash of hypoid driven gear.
  • Used for adjusting preload on the front differential taper roller bearing.
G05002921Courtesy of SUBARU OF AMERICA, INC.
 498937000 TRANSMISSION HOLDER Used for removing and installing the main shaft assembly lock nut.
G05002922Courtesy of SUBARU OF AMERICA, INC.
 499277100 BUSHING 1-2 INSTALLER
  • Used for installing the drive pinion shaft assembly washer.
  • Used for installing the front differential taper roller bearing inner race.
G05002923Courtesy of SUBARU OF AMERICA, INC.
 499277200 INSTALLER
  • Used for installing the 3rd-4th driven gear, 5th driven gear, ball bearing and 6th driven gear.
  • Used for installing the drive pinion shaft assembly washer.
G08541036Courtesy of SUBARU OF AMERICA, INC.
 927640000 INSTALLER Used for installing the taper roller bearing (transfer case side) of transfer driven gear.
G13591433Courtesy of SUBARU OF AMERICA, INC.
 18658AA021 WRENCH COMPL RETAINER
  • Used for removing and installing the differential side retainer.
  • Used for adjusting preload on the front differential taper roller bearing.
  • Used for adjusting the backlash of hypoid driven gear.
G13604444Courtesy of SUBARU OF AMERICA, INC.
 18722AA010 REMOVER Used for removing the 5th drive gear and 6th drive gear.
G13604445Courtesy of SUBARU OF AMERICA, INC.
 499877000 RACE 4-5 INSTALLER
  • Used for installing the 4th, 5th and 6th drive gear needle bearing races and the main shaft assembly double taper roller bearings.
  • Used together with REMOVER (899714110).
G13604446Courtesy of SUBARU OF AMERICA, INC.
 499917500 DRIVE PINION GAUGE ASSY Used for adjusting the drive pinion shaft assembly shim.
G05002930Courtesy of SUBARU OF AMERICA, INC.
 499927100 HANDLE Used for backlash measurement of the hypoid driven gear and preload adjustment of the front differential taper roller bearing.
G05002931Courtesy of SUBARU OF AMERICA, INC.
 499937100 TRANSMISSION STAND Used for disassembling and assembling the transmission.
G05002932Courtesy of SUBARU OF AMERICA, INC.
 499987003 SOCKET WRENCH (35) Used for removing and installing the main shaft assembly lock nut.
G07914998Courtesy of SUBARU OF AMERICA, INC.
 499987300 SOCKET WRENCH (50) Used for removing and installing the driven shaft lock nut.
G13604451Courtesy of SUBARU OF AMERICA, INC.
 899714110 REMOVER Used for removing and installing the parts of main shaft assembly and driven shaft.
G13591917Courtesy of SUBARU OF AMERICA, INC.
 899864100 REMOVER
  • Used for removing the parts of the main shaft assembly.
  • Used for removing the transfer driven gear taper roller bearing (transfer case side) and for installing it (extension case side).
  • Used for removing the transfer drive gear ball bearing.
  • Used for installing the transfer case taper roller bearing.
G13604453Courtesy of SUBARU OF AMERICA, INC.
 18680AA020 HOLDER
  • Used for removing and installing the drive pinion shaft assembly lock nut.
  • Used for removing and installing the driven shaft lock nut.
G13591918Courtesy of SUBARU OF AMERICA, INC.
 899904100 STRAIGHT PIN REMOVER Used for removing and installing the straight pin.
G13603043Courtesy of SUBARU OF AMERICA, INC.
 398497701 SEAT
  • Used for installing the front differential taper roller bearing.
  • Used together with BUSHING 1-2 INSTALLER (499277100).
G13591892Courtesy of SUBARU OF AMERICA, INC.
 498057300 INSTALLER Used for installing the extension case oil seal.
G13591897Courtesy of SUBARU OF AMERICA, INC.
 498255400 PLATE Used for measuring the hypoid driven gear backlash.
G13591944Courtesy of SUBARU OF AMERICA, INC.
 41099AA012 ENGINE SUPPORT BRACKET
  • Used for supporting engine.
  • Used together with ENGINE

    SUPPORT (41099AA020).

  • ENGINE SUPPORT BRACKET (41099AA010) or ENGINE SUPPORT BRACKET (41099AA011) can also be used.
G13603094Courtesy of SUBARU OF AMERICA, INC.
 41099AA020 ENGINE SUPPORT
  • Used for supporting engine.
  • Used together with ENGINE SUPPORT BRACKET (41099AA012).
G13591889Courtesy of SUBARU OF AMERICA, INC.
 398527700 PULLER ASSY
  • Used for removing the extension case oil seal.
  • Used for removing the front differential taper roller bearing outer race.
  • Used for removing the differential side retainer oil seal.
G13604461Courtesy of SUBARU OF AMERICA, INC.
 398643600 GAUGE Used for adjusting the extension end play.
G13603041Courtesy of SUBARU OF AMERICA, INC.
 398177700 INSTALLER
  • Used for installing the transfer drive gear ball bearing.
  • Used for installing the 4th drive gear needle bearing race.
G13604150Courtesy of SUBARU OF AMERICA, INC.
 498175500 INSTALLER Used for installing the taper roller bearing of transfer driven gear (extension case side).
G13591581Courtesy of SUBARU OF AMERICA, INC.
 28399SA010 OIL SEAL PROTECTOR Used for protecting the oil seal from damage when inserting the front drive shaft.
G13591929Courtesy of SUBARU OF AMERICA, INC.
 18675AA000 DIFFERENTIAL SIDE OIL SEAL INSTALLER Used for installing the differential side retainer oil seal.
G13604466Courtesy of SUBARU OF AMERICA, INC.
 398791700 REMOVER Used for removing and installing the straight pin.
G13604467Courtesy of SUBARU OF AMERICA, INC.
 18662AA010 SOCKET (27)
  • Used for removing and installing the drive pinion shaft assembly lock nut.
  • Used for measuring the starting torque of the drive pinion shaft assembly.
G06652244Courtesy of SUBARU OF AMERICA, INC.
 899754112 PRESS
  • Used for removing driven shaft parts.
  • Used to install the main shaft assembly ball bearing.
G13604469Courtesy of SUBARU OF AMERICA, INC.
 18631AA000 HANDLE Used for installing transfer case assembly and extension case assembly.
G13591935Courtesy of SUBARU OF AMERICA, INC.
 18762AA001 COMPRESSOR SPECIAL TOOL
  • Used for removing the 1st driven gear.
  • COMPRESSOR SPECIAL TOOL (18762AA000) can also be used.
G13602207Courtesy of SUBARU OF AMERICA, INC.
 18654AA000 INSTALLER Used for installing the 2nd driven gear bushing.
G13591927Courtesy of SUBARU OF AMERICA, INC.
 18657AA000 INSTALLER Used for installing the transfer case oil seal.
G07915021Courtesy of SUBARU OF AMERICA, INC.
 498267200 CYLINDER HEAD TABLE Used for removing and installing the roller bearing of the transfer case.
G07915022Courtesy of SUBARU OF AMERICA, INC.
 498267300 CYLINDER HEAD TABLE Used for removing and installing the roller bearing of the transfer case.
G13591937Courtesy of SUBARU OF AMERICA, INC.
 18763AA000 COMPRESSOR SHAFT Used for removing and installing the needle bearing of the transfer case.
G13591898Courtesy of SUBARU OF AMERICA, INC.
 498277200 STOPPER SET
  • Used for installing the needle bearing of the transfer case.
  • Use only the spacer.
scientia non olet · About LEMON Manuals