Special Tool

WARNING: This page is about a different car, the 2020 Subaru Impreza. However, it is still accessible from the selected car via links, so may be relevant.

ILLUSTRATION	TOOL NUMBER	DESCRIPTION	REMARKS
Courtesy of SUBARU OF AMERICA, INC.	18769AA010	EXPANDER PULLEY	Used for removing and installing the secondary pulley assembly.
Courtesy of SUBARU OF AMERICA, INC.	18767AA010	BEARING REMOVER	Used for removing the ball bearing of transfer clutch assembly.
Courtesy of SUBARU OF AMERICA, INC.	18762AA010	COMPRESSOR SPECIAL TOOL	Used for removing and installing snap ring of forward clutch assembly.
Courtesy of SUBARU OF AMERICA, INC.	18761AA010	SHEET SPECIAL TOOL	Used for removing and installing control valve body. Used for removing and installing valve cover. Used for removing and installing transmission harness.
Courtesy of SUBARU OF AMERICA, INC.	18681AA010	PRESSURE GAUGE ADAPTER	Used for measuring the secondary pressure (line pressure). NOTE: Used together with the genuine O-ring (part No. 806916050).
Courtesy of SUBARU OF AMERICA, INC.	18801AA000	OIL PRESSURE GAUGE ASSY	Used for measuring the secondary pressure (line pressure). NOTE: Used together with the genuine O-ring (part No. 806908150).
Courtesy of SUBARU OF AMERICA, INC.	18658AA021	WRENCH COMPL RETAINER	Used for removing and installing the differential side retainer.
Courtesy of SUBARU OF AMERICA, INC.	18460AA040	CHECK BOARD	Used for measuring voltage and resistance of TCM terminals.
Courtesy of SUBARU OF AMERICA, INC.	18362AA020	ADAPTER	Used for measuring the transfer clutch hydraulic pressure.
Courtesy of SUBARU OF AMERICA, INC.	18681AA050	ADAPTER PRESSURE GAUGE	Used for measuring the transfer clutch hydraulic pressure. NOTE: Used with genuine union screw (Part No. 801914010) and gasket (Part No. 803914060).
Courtesy of SUBARU OF AMERICA, INC.	498575400	OIL PRESSURE GAUGE ASSY	Used for measuring the transfer clutch hydraulic pressure. NOTE: Used together with the genuine O-ring (part No. 806908150).
Courtesy of SUBARU OF AMERICA, INC.	498277200	STOPPER SET	Used for removing and installing transmission assembly to engine. Used for preventing the torque converter from dropping off.
Courtesy of SUBARU OF AMERICA, INC.	398527700	PULLER ASSY	Used for removing the bearing outer race of the drive pinion shaft. Used for removing the bearing of transmission case.
Courtesy of SUBARU OF AMERICA, INC.	18760AA000	CLAW	Used for removing the bearing of transmission case. Used together with PULLER ASSY (398527700).
Courtesy of SUBARU OF AMERICA, INC.	398673600	COMPRESSOR	Used for removing and installing snap ring of forward clutch assembly.
Courtesy of SUBARU OF AMERICA, INC.	18355AA000	PULLEY WRENCH	Used for removing and installing the lock nut of reduction driven gear. Used together with PULLEY WRENCH PIN SET (18334AA000).
Courtesy of SUBARU OF AMERICA, INC.	18334AA000	PULLEY WRENCH PIN SET	Used for removing and installing the lock nut of reduction driven gear. Used together with PULLEY WRENCH (18355AA000).
Courtesy of SUBARU OF AMERICA, INC.	499987003	SOCKET WRENCH (35)	Used for removing and installing the lock nut of reduction driven gear.
Courtesy of SUBARU OF AMERICA, INC.	498057300	INSTALLER	Used for installing the extension case oil seal.
Courtesy of SUBARU OF AMERICA, INC.	18632AA000	STAND ASSY	Used for disassembling and assembling the transmission.
Courtesy of SUBARU OF AMERICA, INC.	498515500	REMOVER	Used for removing the bearing inner race of the drive pinion shaft.
Courtesy of SUBARU OF AMERICA, INC.	498255400	PLATE	Used for measuring the backlash of hypoid gear.
Courtesy of SUBARU OF AMERICA, INC.	18675AA000	DIFFERENTIAL SIDE OIL SEAL INSTALLER	Used for installing the differential side retainer oil seal.
Courtesy of SUBARU OF AMERICA, INC.	18762AA001	COMPRESSOR SPECIAL TOOL	Used for disassembling and installing the multi-plate clutch piston. COMPRESSOR SPECIAL TOOL (18762AA000) can also be used.
Courtesy of SUBARU OF AMERICA, INC.	927720000	HOUSING BUSHING INSTALLER AND REMOVER	Used for installing drive pinion retainer oil seal. Use BUSHING SHAFT (927880000). Used for installing the oil seal of the oil pump chain cover. Use BUSHING SHAFT (927880000) and BASE TUBE LATERAL LINK (927890000).
Courtesy of SUBARU OF AMERICA, INC.	18763AA000	COMPRESSOR SHAFT	Used for measuring the backlash of hypoid gear.
Courtesy of SUBARU OF AMERICA, INC.	28399SA010	OIL SEAL PROTECTOR	Used for protecting oil seal when installing front drive shaft.
Courtesy of SUBARU OF AMERICA, INC.	498937110	HOLDER	Used for removing and installing the drive pinion lock nut. Used as a holder to rotate gear when checking tooth contact.
Courtesy of SUBARU OF AMERICA, INC.	41099AA012	ENGINE SUPPORT BRACKET	Used for supporting the engine.
Courtesy of SUBARU OF AMERICA, INC.	41099AA020	ENGINE SUPPORT	Used for supporting the engine.
Courtesy of SUBARU OF AMERICA, INC.	18270KA020	SOCKET (E20)	Used for removing and installing the hypoid driven gear. Used for removing and installing the drive pinion shaft retainer.
Courtesy of SUBARU OF AMERICA, INC.	398497701	SEAT	Used for removing and installing the bearing.
Courtesy of SUBARU OF AMERICA, INC.	398177700	INSTALLER	Used for installing the ball bearing. Used for installing the parking gear. Used for installing the bearing outer race. Used for installing the plug.
Courtesy of SUBARU OF AMERICA, INC.	28499TC010	PRESS SNAP RING	Used for installing the bearing outer race of drive pinion shaft.
Courtesy of SUBARU OF AMERICA, INC.	899864100	REMOVER	Used for removing and installing the ball bearing. Used for removing the parking gear and transfer drive gear. Used for removing the bearing inner race of the front differential.
Courtesy of SUBARU OF AMERICA, INC.	498077000	REMOVER	Used for removing the bearing inner race of the front differential.
Courtesy of SUBARU OF AMERICA, INC.	18657AA010	INSTALLER	Used for installing the oil seal at shifter arm shaft portion.
Courtesy of SUBARU OF AMERICA, INC.	498077600	REMOVER	Used for removing the ball bearing of drive sprocket.
Courtesy of SUBARU OF AMERICA, INC.	18723AA000	REMOVER	Used for removing the ball bearing of transfer clutch assembly.
Courtesy of SUBARU OF AMERICA, INC.	498497300	CRANKSHAFT STOPPER	Used for stopping the drive plate rotation when removing and installing the drive plate.
Courtesy of SUBARU OF AMERICA, INC.	18270AA050	SOCKET	Used for installing the drive plate mounting bolt. NOTE: This tool is made by KYOTO TOOL Co., Ltd. (KTC). Item number: B3-14W To make it easier to obtain, it has been specified as a special tool.
Courtesy of SUBARU OF AMERICA, INC.	399513600	INSTALLER	Used for removing the ball bearing of drive sprocket.
Courtesy of SUBARU OF AMERICA, INC.	499267300	STOPPER PIN	Used for adjusting the inhibitor switch.
Courtesy of SUBARU OF AMERICA, INC.	499277100	BUSHING 1-2 INSTALLER	Used for installing the ball bearing of the transmission case. Used for installing the bearing inner race.
Courtesy of SUBARU OF AMERICA, INC.	499277200	INSTALLER	Used for installing the ball bearing of the transfer clutch assembly.
Courtesy of SUBARU OF AMERICA, INC.	499575400	GAUGE	Used for measuring height of end play.
Courtesy of SUBARU OF AMERICA, INC.	499575500	GAUGE	Used for measuring height of end play.
Courtesy of SUBARU OF AMERICA, INC.	499787500	ADAPTER	Used for removing and installing the drive pinion shaft lock nut. Used for measuring the preload of the drive pinion shaft. Used for measuring the backlash of hypoid gear.
Courtesy of SUBARU OF AMERICA, INC.	499575600	GAUGE	Used for measuring height of end play.
Courtesy of SUBARU OF AMERICA, INC.	499787700	WRENCH	Used for removing and installing the drive pinion shaft lock nut. Used for measuring the preload of the drive pinion shaft. Used for measuring the backlash of hypoid gear.
Courtesy of SUBARU OF AMERICA, INC.	499757002	INSTALLER	Used for removing the bearing of reduction driven gear. Used for installing the parking gear. Used for installing the transfer drive gear.
Courtesy of SUBARU OF AMERICA, INC.	899580100	INSTALLER	Used for installing the collar of reduction driven gear. Used for installing the ball bearing of the transfer driven gear. Used for installing the bearing inner race of drive pinion shaft.
Courtesy of SUBARU OF AMERICA, INC.	498077300	REMOVER	Used for installing the ball bearing of reduction driven gear.
Courtesy of SUBARU OF AMERICA, INC.	499755502	PRESS SNAP RING	Used for installing the drive sprocket ball bearing.
Courtesy of SUBARU OF AMERICA, INC.	499755602	PRESS SNAP RING	Used for installing the oil seal. Used for installing the plug.
Courtesy of SUBARU OF AMERICA, INC.	498077400	REMOVER	Used for removing the ball bearing of transfer driven gear.
Courtesy of SUBARU OF AMERICA, INC.	20099AE020	INSTALLER	Used for installing the bearing outer race of drive pinion shaft.
Courtesy of SUBARU OF AMERICA, INC.	927130000	EXTENSION DRIVE SHAFT	Used for installing the bearing inner race of drive pinion shaft.
Courtesy of SUBARU OF AMERICA, INC.	18270AA040	SOCKET	Used for removing and installing the transfer clutch pressure test plug.
Courtesy of SUBARU OF AMERICA, INC.	73099SG000	SPECIAL TOOL CONDENSER	Used for installing the transfer clutch pressure test plug.
Courtesy of SUBARU OF AMERICA, INC.	20399AG000	STRUT MOUNT SOCKET	Used for tightening the strut mount self-locking nut.
Courtesy of SUBARU OF AMERICA, INC.	-	SUBARU SELECT MONITOR 4	Used for setting of each function and troubleshooting for electrical system. NOTE: For detailed operation procedures, refer to "Help" of application.