DTC P2404: EVAP System Leak Detection Pump Sense Circuit Range/Performance: Notes

WARNING: This page is about a different variant/trim than selected.

DTC detecting condition:

Detected when two consecutive driving cycles with fault occur.

CAUTION: After servicing or replacing faulty parts, perform Clear Memory Mode Ref. to OPERATION , Clear Memory Mode and Inspection Mode Ref. to PROCEDURE , Inspection Mode.

Wiring diagram:

Engine Electrical System Ref. to WIRING DIAGRAM , Engine Electrical System.

Fig 1: EVAP System Leak Detection Pump Sense Circuit Range/Performance Wiring Diagram

Courtesy of SUBARU OF AMERICA, INC.

Step	Check	Yes	No
1 CHECK FOR ANY OTHER DTC ON DISPLAY.	Is any other DTC displayed?	Check the appropriate DTC using the "List of Diagnostic Trouble Code (DTC)". Ref. to LIST OF DIAGNOSTIC TROUBLE CODE (DTC)	Go to step 2
2 CHECK LEAK CHECK VALVE ASSEMBLY PUMP. Using the Subaru Select Monitor, operate the leak check valve assembly pump. NOTE: For detailed operation procedures, refer to the "Active Test". Ref. to ACTIVE TEST	Does the leak check valve assembly pump operate?	Go to step 6	Go to step 3
3 CHECK POWER SUPPLY OF LEAK CHECK VALVE ASSEMBLY. Turn the ignition switch to OFF. Disconnect the connector from the leak check valve assembly. Turn the ignition switch to ON. Measure the voltage between the leak check valve assembly connector and chassis ground. Connector & terminal (R400) No. 3 (+) - Chassis ground (-):	Is the voltage 10 V or more?	Go to step 4	Repair the harness and connector. NOTE: In this case, repair the following item: Open circuit in harness between the main relay and the leak check valve assembly connector Poor contact of main relay connector Poor contact of coupling connector
4 CHECK HARNESS BETWEEN ECM AND LEAK CHECK VALVE ASSEMBLY CONNECTOR. Turn the ignition switch to OFF. Disconnect the connector from ECM. Measure the resistance of harness between ECM connector and the leak check valve assembly connector. Connector & terminal (B134) No. 9 - (R400) No. 4:	Is the resistance less than 1 Ω?	Go to step 5	Repair the harness and connector. NOTE: In this case, repair the following item: Open circuit in harness between ECM connector and the leak check valve assembly connector Poor contact of coupling connector
5 CHECK HARNESS BETWEEN ECM AND LEAK CHECK VALVE ASSEMBLY CONNECTOR. Measure the resistance of harness between ECM connector and chassis ground. Connector & terminal (B134) No. 9 - Chassis ground:	Is the resistance 1 MΩ or more?	Replace the leak check valve assembly. Ref. to LEAK CHECK VALVE ASSEMBLY	Repair the short circuit to ground in harness between ECM connector and leak check valve assembly connector.
6 CHECK LEAK CHECK VALVE ASSEMBLY SWITCHING VALVE. Using the Subaru Select Monitor, operate the leak check valve assembly switching valve. NOTE: For detailed operation procedures, refer to the "Active Test". Ref. to ACTIVE TEST	Does the leak check valve assembly switching valve operate?	Go to step 10	Go to step 7
7 CHECK POWER SUPPLY OF LEAK CHECK VALVE ASSEMBLY. Turn the ignition switch to OFF. Disconnect the connector from the leak check valve assembly. Turn the ignition switch to ON. Measure the voltage between the leak check valve assembly connector and chassis ground. Connector & terminal (R400) No. 5 (+) - Chassis ground (-):	Is the voltage 10 V or more?	Go to step 8	Repair the harness and connector. NOTE: In this case, repair the following item: Open circuit in harness between the main relay and the leak check valve assembly connector Poor contact of main relay connector Poor contact of coupling connector
8 CHECK HARNESS BETWEEN ECM AND LEAK CHECK VALVE ASSEMBLY CONNECTOR. Turn the ignition switch to OFF. Disconnect the connector from ECM. Measure the resistance of harness between ECM connector and the leak check valve assembly connector. Connector & terminal (B134) No. 61 - (R400) No. 1:	Is the resistance less than 1 Ω?	Go to step 9	Repair the harness and connector. NOTE: In this case, repair the following item: Open circuit in harness between ECM connector and the leak check valve assembly connector Poor contact of coupling connector
9 CHECK HARNESS BETWEEN ECM AND LEAK CHECK VALVE ASSEMBLY CONNECTOR. Measure the resistance of harness between ECM connector and chassis ground. Connector & terminal (B134) No. 61 - Chassis ground:	Is the resistance 1 MΩ or more?	Replace the leak check valve assembly. Ref. to LEAK CHECK VALVE ASSEMBLY	Repair the short circuit to ground in harness between ECM connector and leak check valve assembly connector.
10 CHECK EVAPORATIVE EMISSION CONTROL SYSTEM. Perform drive cycle I. Ref. to DRIVE CYCLE I , PROCEDURE, Drive Cycle.	Is DTC P2404 displayed on the display?	Replace the leak check valve assembly. Ref. to LEAK CHECK VALVE ASSEMBLY	Even if DTC is detected, the circuit has returned to a normal condition at this time. Reproduce the failure, and then perform the diagnosis again. NOTE: In this case, temporary poor contact of connector, temporary open or short circuit of harness may be the cause.