Section 1 (Emission Control Systems (Aux. Emission Control Devices) (H6DO)): Canister: Installation

WARNING: This page is about a different variant/trim than selected.

Install the leak check valve assembly to the canister.
Tightening torque:

8 N.m (0.8 kgf-m, 5.9 ft-lb)
Connect the drain tube (A).
CAUTION:
- Check that there is no damage or dust on the quick connector. If necessary, clean the seal surface of the pipe.
- Make sure that the quick connector is securely connected.
NOTE: Connect the quick connector as shown in the figure.

Fig 1: Connecting Quick Connector
Courtesy of SUBARU OF AMERICA, INC.

Fig 2: Locating Quick Connector And Bolts
Courtesy of SUBARU OF AMERICA, INC.
Connect the vent tube (A), canister drain tube (B) and purge tube (C), and install the hose clamp (D).
CAUTION:
- Make sure there are no damage or dust on connections. If necessary, clean the seal surface of the pipe.
- Make sure that the quick connector is securely connected.
NOTE: Connect the quick connector as shown in the figure.
- Vent tube (A) and canister drain tube (B) (Slider color is red or green.)
  
  Fig 3: Connecting Quick Connector (Slider Color Red Or Green)
  Courtesy of SUBARU OF AMERICA, INC.
- Vent tube (A) and canister drain tube (B) (Slider color is white.)
  
  Fig 4: Connecting Quick Connector (Slider Color White)
  Courtesy of SUBARU OF AMERICA, INC.
- Purge tube (C)
Fig 5: Connecting Quick Connector
Courtesy of SUBARU OF AMERICA, INC.

Fig 6: Vent Tube And Canister Drain Tube
Courtesy of SUBARU OF AMERICA, INC.
Install the canister protector.
Tightening torque:

8 N.m (0.8 kgf-m, 5.9 ft-lb)

Fig 7: Locating Canister Protector Bolts
Courtesy of SUBARU OF AMERICA, INC.
Install the canister.
Tightening torque:

8 N.m (0.8 kgf-m, 5.9 ft-lb)
Connect the connector (A) to the canister and install the harness clip (B).

Fig 8: Connecting Connector To Canister
Courtesy of SUBARU OF AMERICA, INC.
Connect the quick connectors of the vent tube (A), canister drain tube (B) and purge tube (C), and install the tube clamp (D).
CAUTION:
- Make sure there are no damage or dust on connections. If necessary, clean the seal surface of the pipe.
- Make sure that the quick connector is securely connected.
NOTE: Connect the quick connector as shown in the figure.
- Vent tube (A) and canister drain tube (B) (Slider color is red or green.)
  
  Fig 9: Connecting Quick Connector (Slider Color Red Or Green)
  Courtesy of SUBARU OF AMERICA, INC.
- Vent tube (A) and canister drain tube (B) (Slider color is white.)
  
  Fig 10: Connecting Quick Connector (Slider Color White)
  Courtesy of SUBARU OF AMERICA, INC.
- Purge tube (C)
Fig 11: Connecting Quick Connector
Courtesy of SUBARU OF AMERICA, INC.

Fig 12: Vent Tube, Canister Drain Tube And Purge Tube
Courtesy of SUBARU OF AMERICA, INC.
Install the rear mud guard LH. <Ref. to INSTALLATION , Mud Guard.>
Lower the vehicle.
Install the rear wheel LH. <Ref. to INSTALLATION , Tire and Wheel.>
Connect the ground terminal to battery sensor. <Ref. to BATTERY , NOTE, Repair Contents.>