Special Tool

WARNING: This page is about a different variant/trim than selected.

TOOL NUMBER	DESCRIPTION	REMARKS
18769AA010	EXPANDER PULLEY	Used for removing and installing the secondary pulley assembly.
18767AA010	BEARING REMOVER	Used for removing the ball bearing of transfer clutch assembly.
18762AA010	COMPRESSOR SPECIAL TOOL	Used for removing and installing snap ring of forward clutch assembly.
18761AA010	SHEET SPECIAL TOOL	Used for removing and installing control valve body. Used for removing and installing valve cover. Used for removing and installing transmission harness.
18681AA010	PRESSURE GAUGE ADAPTER	Used for measuring the secondary pressure (line pressure). NOTE: Used together with the genuine O-ring (part No. 806916050).
18801AA000	OIL PRESSURE GAUGE ASSY	Used for measuring the secondary pressure (line pressure).
18658AA020	WRENCH COMPL RETAINER	Used for removing and installing the differential side retainer.
18460AA040	CHECK BOARD	Used for measuring TCM terminal voltage and resistance.
34099AC020	ADAPTER HOSE B	Used for measuring the transfer clutch hydraulic pressure. NOTE: Used with genuine union screw (Part No. 801914010) and gasket (Part No. 803914060).
34099AC010	ADAPTER HOSE A	Used for measuring the transfer clutch hydraulic pressure.
18681AA000	PRESSURE GAUGE ADAPTER	Used for measuring the transfer clutch hydraulic pressure. NOTE: Used together with the genuine O-ring (part No. 806911080).
498575400	OIL PRESSURE GAUGE ASSY	Used for measuring the transfer clutch hydraulic pressure.
498277200	STOPPER SET	Used for removing and installing transmission assembly to engine. Used for preventing the torque converter from dropping off.
398527700	PULLER ASSY	Used for removing the extension case oil seal. Used for removing the bearing outer race of the drive pinion shaft. Used for removing the bearing of transmission case.
18760AA000	CLAW	Used for removing the bearing of transmission case. Used together with PULLER ASSY (398527700).
398673600	COMPRESSOR	Used for removing and installing snap ring of forward clutch assembly.
18355AA000	PULLEY WRENCH	Used for removing and installing the lock nut of reduction driven gear. Used together with PIN SET (18334AA000).
18334AA000	PULLEY WRENCH PIN SET	Used for removing and installing the lock nut of reduction driven gear. Used together with PULLEY WRENCH (18355AA000).
499987003	SOCKET WRENCH (35)	Used for removing and installing the lock nut of reduction driven gear.
498057300	INSTALLER	Used for installing the extension case oil seal.
18632AA000	STAND ASSY	Used for disassembling and assembling the transmission.
498515500	REMOVER	Used for removing the bearing inner race of the drive pinion shaft.
498255400	PLATE	Used for measuring the backlash of hypoid gear.
498247001	MAGNET BASE	Used for measuring the backlash of differential bevel pinion gear. Used for measuring the backlash of hypoid gear. Used together with DIAL GAUGE (498247100).
498247100	DIAL GAUGE	Used for measuring the backlash of differential bevel pinion gear. Used for measuring the backlash of hypoid gear. Used together with MAGNET BASE (498247001).
18675AA000	DIFFERENTIAL SIDE OIL SEAL INSTALLER	Used for installing the differential side retainer oil seal.
18762AA001	COMPRESSOR SPECIAL TOOL	Used for disassembling and installing the multi-plate clutch piston. COMPRESSOR SPECIAL TOOL (18762AA000) can also be used.
927720000	HOUSING BUSHING INSTALLER AND REMOVER	Used for installing the oil seal. Use BUSHING SHAFT (927880000).
18763AA000	COMPRESSOR SHAFT	Used for measuring the backlash of hypoid gear.
28399SA010	OIL SEAL PROTECTOR	Used for protecting oil seal when installing front drive shaft.
498937110	HOLDER	Used for removing and installing the drive pinion lock nut. Used as a holder to rotate gear when checking tooth contact.
41099AA012	ENGINE SUPPORT BRACKET	Used for supporting the engine. ENGINE SUPPORT BRACKET (41099AA010 or 41099AA011) can also be used.
41099AA020	ENGINE SUPPORT	Used for supporting the engine.
18270KA020	SOCKET (E20)	Used for removing and installing the hypoid driven gear. Used for removing and installing the drive pinion shaft retainer.
398497701	SEAT	Used for removing and installing the bearing.
398177700	INSTALLER	Used for installing the ball bearing. Used for installing the parking gear. Used for installing the bearing outer race. Used for installing the plug.
28499TC010	PRESS SNAP RING	Used for installing the ball bearing of the transmission case. Used for installing the bearing outer race of drive pinion shaft.
899864100	REMOVER	Used for removing and installing the ball bearing. Used for removing the parking gear and transfer drive gear. Used for removing the bearing inner race of the front differential.
498077000	REMOVER	Used for removing the bearing inner race of the front differential.
18657AA010	INSTALLER	Used for installing the oil seal at shifter arm shaft portion.
498077600	REMOVER	Used for removing the ball bearing of drive sprocket.
18720AA000	REMOVER	Used for removing the ball bearing of transfer clutch assembly.
498497300	CRANKSHAFT STOPPER	Used for stopping the drive plate rotation when removing and installing the drive plate.
399513600	INSTALLER	Used for removing the ball bearing of drive sprocket.
499267300	STOPPER PIN	Used for adjusting the inhibitor switch.
499277100	BUSHING 12 INSTALLER	Used for installing the bearing of the transmission case. Used for installing the ball bearing. Used for installing the bearing inner race.
499277200	INSTALLER	Used for installing the ball bearing of the transfer clutch assembly.
499575400	GAUGE	Used for measuring height of end play.
499575500	GAUGE	Used for measuring height of end play.
499787500	ADAPTER	Used for removing and installing the drive pinion shaft lock nut. Used for measuring the preload of the drive pinion shaft. Used for measuring the backlash of hypoid gear.
499575600	GAUGE	Used for measuring height of end play.
499787700	WRENCH	Used for removing and installing the drive pinion shaft lock nut. Used for measuring the preload of the drive pinion shaft. Used for measuring the backlash of hypoid gear.
499757002	INSTALLER	Used for removing the bearing of reduction driven gear. Used for installing the parking gear. Used for installing the transfer drive gear.
899580100	INSTALLER	Used for installing the collar of reduction driven gear. Used for installing the ball bearing of the transfer driven gear. Used for installing the bearing inner race of drive pinion shaft.
498077300	REMOVER	Used for installing the ball bearing of reduction driven gear.
499755602	PRESS SNAP RING	Used for installing the oil seal. Used for installing the ball bearing and roller bearing. Used for installing the plug.
498077400	REMOVER	Used for removing the ball bearing of transfer driven gear.
20099AE020	INSTALLER	Used for installing the bearing outer race of drive pinion shaft.
927130000	EXTENSION DRIVE SHAFT	Used for installing the bearing inner race of drive pinion shaft.
18270AA040	SOCKET	Used for removing and installing the transfer clutch pressure test plug.
73099SG000	SPECIAL TOOL CONDENSER	Used for installing the transfer clutch pressure test plug.
- (Newly adopted tool)	SUBARU SELECT MONITOR 4	Used for setting of each function and troubleshooting for electrical system. NOTE: For detailed operation procedures of Subaru Select Monitor 4, refer to "Application help".