Section 2 (Starting System & Charging System (H4DO)): General Description: Specification
WARNING: This page is about a different variant/trim than selected.
- Non-turbo model
| Item | Specifications | |||
|---|---|---|---|---|
| Vehicle model | Non-turbo model | |||
| CVT | MT | |||
| Starter | Type | Reduction type | ||
| Model | M000T38571 | M000T33176 | ||
| Manufacturer | Mitsubishi Electric | |||
| Voltage and output | 12 V -1.2 kW | 12 V -1.0 kW | ||
| Direction of rotation | Counterclockwise (when observed from pinion) | |||
| Number of pinion teeth | 9 | 8 | ||
| No-load characteristics | Voltage | 11 V | ||
| Current | 90 A or less | 95 A or less | ||
| Generator | Type | Rotating-field three-phase type, voltage regulator built-in type, with load response control system | ||
| Model | A5TV0081 | |||
| Manufacturer | Mitsubishi Electric | |||
| Voltage and output | 12 V - 150 A | |||
| Polarity on ground side | Negative | |||
| Direction of rotation | Clockwise (when observed from pulley side) | |||
| Stator connection | 3-phase < delta → type | |||
| Output current | 1, 500 r/min- 44 A or more 2, 500 r/min- 121 A or more 5, 000 r/min- 148 A or more |
|||
| Regulated voltage | 14.0-14.6 V [20°C (68°F)] | |||
| Rotor slip ring outer diameter | Standard | 22.7 mm (0.894 in) | ||
| Limit | 22.1 mm (0.870 in) | |||
| Brush length | Standard | 22.5 mm (0.886 in) | ||
| Limit | 5.0 mm (0.197 in) | |||
| Battery | Type | 55D23L/75D23L | ||
| Nominal capacity | 5 HR: 40 Ah [25°C (77°F)] (55D23L)/5 HR: 53 Ah [25°C (77°F)] (75D23L) | |||
| Nominal voltage | 12 V | |||
| CCA | 390 A (55D23L)/470 A (75D23L) | |||
- Turbo model
| Item | Specifications | ||
|---|---|---|---|
| Starter | Type | Reduction type | |
| Model | M000T20176 | ||
| Manufacturer | Mitsubishi Electric | ||
| Voltage and output | 12 V -1.4 kW | ||
| Direction of rotation | Counterclockwise (when observed from pinion) | ||
| Number of pinion teeth | 9 | ||
| No-load characteristics | Voltage | 11 V | |
| Current | 90 A or less | ||
| Generator | Type | Rotating-field three-phase type, voltage regulator built-in type, with load response control system | |
| Model | A2TX3381 | ||
| Manufacturer | Mitsubishi Electric | ||
| Voltage and output | 12 V - 130 A | ||
| Polarity on ground side | Negative | ||
| Direction of rotation | Clockwise (when observed from pulley side) | ||
| Stator connection | 3-phase type | ||
| Output current | 1, 500 r/min - 50 A or more 2, 500 r/min - 111 A or more 5, 000 r/min - 133 A or more |
||
| Regulated voltage | 14.1-14.8 V [20°C (68°F)] | ||
| Rotor slip ring outer diameter | Standard | 22.7 mm (0.894 in) | |
| Limit | 22.1 mm (0.870 in) | ||
| Brush length | Standard | 22.5 mm (0.886 in) | |
| Limit | 5.0 mm (0.197 in) | ||
| Battery | Type | 55D23L/75D23L | |
| Nominal capacity | 5 HR: 40 Ah [25°C (77°F)] (55D23L)/5 HR: 53 Ah [25°C (77°F)] (75D23L) | ||
| Nominal voltage | 12 V | ||
| CCA | 390 A (55D23L)/470 A (75D23L) | ||