DTC P062D Fuel Injector Driver Circuit Performance Bank 1: Notes

DTC detecting condition:

Immediately at fault recognition

Trouble symptom:

Engine does not start.
Engine stalls.

CAUTION:

After servicing or replacing faulty parts, perform Clear Memory Ref. to ENGINE (DIAGNOSTICS) (H4DOTC)>Clear Memory Mode . and Inspection Mode Ref. to ENGINE (DIAGNOSTICS) (H4DOTC)>Inspection Mode .
Use the check board when measuring the ECM terminal voltage and resistance.

Wiring diagram:

Engine Electrical System Ref. to WIRING SYSTEM>Engine Electrical System>WIRING DIAGRAM .

Fig 1: Fuel Injector Driver Circuit Performance Bank 1 - Wiring Diagram

Courtesy of SUBARU OF AMERICA, INC.

CHECK FOR ANY OTHER DTC ON DISPLAY.
Is any other DTC displayed?
- Yes: Check the appropriate DTC using the "List of Diagnostic Trouble Code (DTC)". Ref. to ENGINE (DIAGNOSTICS) (H4DOTC)>List of Diagnostic Trouble Code (DTC) .
- No: Go to 2.
CHECK HARNESS BETWEEN ECM AND FUEL INJECTOR CONNECTOR.
1. Turn the ignition switch to OFF.
2. Disconnect the connector from ECM.
3. Measure the resistance between ECM connectors.
  Connector & terminal
  
  #1 (E158) No. 11 - (E158) No. 12:
  
  #2 (E158) No. 23 - (E158) No. 24:
  
  #3 (E158) No. 35 - (E158) No. 36:
  
  #4 (E158) No. 47 - (E158) No. 48:
Is the resistance 1.89 - 2.31 Ω (at 20°C (68°F))?
- Yes: Go to 4.
- No: Go to 3.
CHECK HARNESS BETWEEN ECM AND FUEL INJECTOR CONNECTOR.
1. Disconnect the connector from fuel injector.
2. Measure the resistance of harness between ECM connector and defective fuel injector connector.
  Connector & terminal
  
  #1 (E158) No. 12 - (E5) No. 1:
  
  #1 (E158) No. 11 - (E5) No. 2:
  
  #2 (E158) No. 24 - (E16) No. 1:
  
  #2 (E158) No. 23 - (E16) No. 2:
  
  #3 (E158) No. 36 - (E6) No. 1:
  
  #3 (E158) No. 35 - (E6) No. 2:
  
  #4 (E158) No. 48 - (E17) No. 1:
  
  #4 (E158) No. 47 - (E17) No. 2:
Is the resistance less than 1 Ω?
- Yes: Repair or replace the following items.
  - Poor contact of fuel injector connector
  - Defective fuel injector Ref. to FUEL INJECTION (FUEL SYSTEMS) (H4DOTC)>Fuel Injector .
- No: Repair the open circuit of the harness between the ECM connector and fuel injector connector.
CHECK HARNESS BETWEEN ECM AND FUEL INJECTOR CONNECTOR.
Measure the resistance between the ECM connector and engine ground.

Connector & terminal

#1 (E158) No. 12 - Engine ground:

#1 (E158) No. 11 - Engine ground:

#2 (E158) No. 24 - Engine ground:

#2 (E158) No. 23 - Engine ground:

#3 (E158) No. 36 - Engine ground:

#3 (E158) No. 35 - Engine ground:

#4 (E158) No. 48 - Engine ground:

#4 (E158) No. 47 - Engine ground:

Is the resistance 1 MΩ or more?
- Yes: Repair the poor contact of ECM connector.
- No: Go to 5.
CHECK HARNESS BETWEEN ECM AND FUEL INJECTOR CONNECTOR.
1. Disconnect the connector from fuel injector.
2. Measure the resistance between ECM connector and engine ground on defective fuel injectors.
  Connector & terminal
  
  #1 (E158) No. 12 - Engine ground:
  
  #1 (E158) No. 11 - Engine ground:
  
  #2 (E158) No. 24 - Engine ground:
  
  #2 (E158) No. 23 - Engine ground:
  
  #3 (E158) No. 36 - Engine ground:
  
  #3 (E158) No. 35 - Engine ground:
  
  #4 (E158) No. 48 - Engine ground:
  
  #4 (E158) No. 47 - Engine ground:
Is the resistance 1 MΩ or more?
- Yes: Replace the faulty fuel injector. Ref. to FUEL INJECTION (FUEL SYSTEMS) (H4DOTC)>Fuel Injector .
- No: Repair the short circuit to ground in harness between ECM connector and fuel injector connector.