DTC P0335 Crankshaft Position Sensor "A" Circuit: Notes

DTC detecting condition:

Immediately at fault recognition

Trouble symptom:

Engine stalls.
Failure of engine to start

CAUTION:

After servicing or replacing faulty parts, perform Clear Memory Ref. to ENGINE (DIAGNOSTICS) (H4DOTC)>Clear Memory Mode . and Inspection Mode Ref. to ENGINE (DIAGNOSTICS) (H4DOTC)>Inspection Mode .
Use the check board when measuring the ECM terminal voltage and resistance.

Wiring diagram:

Engine Electrical System Ref. to WIRING SYSTEM>Engine Electrical System>WIRING DIAGRAM .

Fig 1: Crankshaft Position Sensor A - Wiring Diagram

Courtesy of SUBARU OF AMERICA, INC.

CHECK POWER SUPPLY OF CRANKSHAFT POSITION SENSOR.
1. Turn the ignition switch to OFF.
2. Disconnect the connector from the crankshaft position sensor.
3. Turn the ignition switch to ON.
4. Measure the voltage between crankshaft position sensor connector and engine ground.
  Connector & terminal
  
  (E10) No. 1 (+) - Engine ground (-):
Is the voltage 10 V or more?
- Yes: Go to 2.
- No: repair the harness and connector.
  NOTE:
  In this case, repair the following item:
  - Open circuit or short circuit to ground in harness between main relay connector and crankshaft position sensor connector
  - Poor contact of coupling connector
CHECK HARNESS BETWEEN ECM AND CRANKSHAFT POSITION SENSOR CONNECTOR.
1. Turn the ignition switch to OFF.
2. Disconnect the connector from ECM.
3. Measure the resistance between the ECM and crankshaft position sensor connector.
  Connector & terminal
  
  (E158) No. 19 - (E10) No. 2:
  
  (E158) No. 31 - (E10) No. 3:
Is the resistance less than 1 Ω?
- Yes: Go to 3.
- No: Repair the open circuit in harness between ECM and crankshaft position sensor connector.
CHECK HARNESS BETWEEN ECM AND CRANKSHAFT POSITION SENSOR CONNECTOR.
Measure the resistance between crankshaft position sensor connector and engine ground.

Connector & terminal

(E10) No. 2 - Engine ground:

(E10) No. 3 - Engine ground:

Is the resistance 1 MΩ or more?
- Yes: Go to 4.
- No: Repair short circuit to ground in harness between ECM and crankshaft position sensor connector.
CHECK HARNESS BETWEEN ECM AND CRANKSHAFT POSITION SENSOR CONNECTOR.
Measure the voltage between crankshaft position sensor connector and engine ground.

Connector & terminal

(E10) No. 2 (+) - Engine ground (-):

(E10) No. 3 (+) - Engine ground (-):

Is the voltage 5 V or more?
- Yes: Repair the short circuit to power in the harness between ECM and crankshaft position sensor connector.
- No: Go to 5.
CHECK CONDITION OF CRANKSHAFT POSITION SENSOR.
Is the crankshaft position sensor installation bolt tightened securely?
- Yes: Go to 6.
- No: Tighten the crankshaft position sensor installation bolt securely. Ref. to FUEL INJECTION (FUEL SYSTEMS) (H4DOTC)>Crankshaft Position Sensor>INSTALLATION .
CHECK CRANKSHAFT POSITION SENSOR.
Check waveform of crankshaft position sensor. Ref. to ENGINE (DIAGNOSTICS) (H4DOTC)>Engine Control Module (ECM) I/O Signal .

Is there any abnormality in waveform?
- Yes: Replace the crankshaft position sensor. Ref. to FUEL INJECTION (FUEL SYSTEMS) (H4DOTC)>Crankshaft Position Sensor .
- No: Repair the following item.
  - Poor contact of ECM connector
  - Poor contact of crankshaft position sensor connector
  - Poor contact of coupling connector