LEMON Manuals: Even more car manuals for everyone
Home >> Subaru >> 2017 >> Forester 2.0XT Touring >> Repair and Diagnosis >> Accessories & Equipment >> Communication Devices >> Body Control System (Diagnostics) >> Registration Body Integrated Unit >> Operation >> Destination Setting

Destination Setting

NOTE: For the vehicle requiring the destination setting, if the destination setting is not finished, display can not be shifted into customizing screen.
  1. CONFIRM CURRENT SETTING. 

    Always perform confirmation of current setting before replacing the module.

    Record the contents of the destination setting.

    NOTE: Refer to the data monitor Ref. to BODY CONTROL(DIAGNOSTICS)>Data Monitor . and current setting Ref. to BODY CONTROL(DIAGNOSTICS)>Registration Body Integrated Unit>OPERATION>CONFIRM CURRENT SETTING . to confirm the current setting.

    Is the current setting recorded?

    • Yes: Go to 2. 
    • No: Confirm the current setting. Go to 1. 
  2. CONFIRM DESTINATION SETTING. 
    1. Connect the Subaru Select Monitor, and run the application.
    2. On [Start] display, select [Diagnosis].
    3. On [Vehicle selection] display, input the target vehicle information and select [OK].
    4. On [Main Menu] display, select [Each System].
    5. On [Select System] display, select [Body Control], and then select [Enter].
    6. On [Select Function] display, select [Customize].
    7. The vehicle destination screen is displayed.

    Is the vehicle destination setting screen displayed?

    • Yes: Go to 3. 
    • No: Go to  4.
  3. CONFIRM DESTINATION SETTING. 

    Confirm the screen displayed on Subaru Select Monitor and the actual vehicle destination.

    Is it necessary to change the destination setting?

    • Yes: Select Yes, and Go to 4. 
    • No: Select No, and Go to  5.
  4. ENTER DESTINATION CODE. 

    Enter the appropriate code in the screen.

    U4, U5, U6, C4 and C0, C5 (models with keyless access with push button start system): U400 C0, C5 (models without the keyless access with push button start system): C000

    Is the appropriate code entered?

    • Yes: Select OK, and Go to 5. 
    • No: Enter the destination code. Go to 4. 
  5. REGISTER VEHICLE EQUIPMENT. 

    Customizing screen is displayed.

    NOTE: Match the each item setting of body integrated unit registration item list with the vehicle equipment.

    Do all setting contents match with the vehicle equipment specification?

    • Yes: Go to 6. 
    • No: Change the items until each content setting match with the vehicle equipment specification. Go to 5. 
  6. CONFIRM MARKET MODE. 
    1. On the customizing screen, select the Factory initial setting to change the setting from Factory mode to Market mode.
    2. Turn the ignition switch to OFF.
      NOTE: When the setting is changed from "Factory" mode to "Market" mode, turning the ignition switch from ON → OFF confirms the setting.
    3. Turn the ignition switch to ON, and check the contents of settings.

    Is the mode changed to "Market" mode?

    • Yes: Go to 7. 
    • No: Perform the destination setting from the first step. Go to  1.
  7. CONFIRM MARKET MODE. 

    Check the following.

    • Destination: When set to U4, U5, U6, C4 and C0, C5 (models with keyless access with push button start system)

      The "destination setting" of the data monitor is set to U4, U5, U6, C4.

    • Destination: When set to C0, C5 (models without keyless access with push button start system) The "destination setting" of the data monitor is set to C0, C5.

    Is the display the same as indicated?

    • Yes: Registration of body integrated unit is finished.
    • No: It is possible that harness malfunction may occur. Perform the diagnosis.
NOTE: How to confirm when the destination code is not known.
Option code (destination code + OP code) Application range Destination code
U4** Must be set for all vehicles. U400
U5**
U6**
C4**
C0** Only models without keyless access with push button start system need settings. C000
C5**
scientia non olet · About LEMON Manuals